Progress Lighting

Package Contents

Diagram Description: Visuals show the main fixture body (A), glass shades (B), and socket rings (C) for different models. The diagrams also illustrate the assembly of the mounting plate and fixture components.

Hardware Contents (not actual size)

• AA

  Screw
  (#8-32)

  Qty: 3

• BB

  Wire connector

  Qty: 1

• CC

  Round Mounting Plate

  Qty: 1

• DD

  Hex Nut
  (#8-32)

  Qty: 2

• EE

  Cylinder Nut
  (#8-32)

  Qty: 2

Diagram Description: Visuals display individual hardware components: screws (AA), wire connectors (BB), a round mounting plate (CC), hex nuts (DD), and cylinder nuts (EE), along with their quantities.

Customer Support

THANK YOU for selecting Progress Lighting

Safety Information

CAUTION:

CAUTION:

WARNING:

CAUTION:

Preparation

1. Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
2. Estimated assembly time: 30 minutes.
3. Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.

Care and Maintenance

Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.

Assembly Instructions

Step 1: Prepare Mounting Plate

Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC). Adjust the screw length according to the fixture canopy depth.

Diagram Description: Shows the round mounting plate (CC) with screws (AA) and hex nuts (DD) attached. Illustrates adjusting the screws (AA) to protrude 3/16 inches (5mm) from the plate for mounting.

Step 2: Attach Assembly to Outlet Box

Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.

Diagram Description: Shows the fixture canopy being lifted to the mounting surface and the screws (AA) passing through the canopy's mounting holes into the round mounting plate (CC). Hex nuts (DD) are tightened onto the screws (AA) to secure the fixture.

Step 3: Wiring Connections

Strip 3/8 inches of insulation from the electrical wire ends.

Connect the WHITE fixture wire to the WHITE supply wire from the outlet box using a wire connector (BB).

Connect the BLACK fixture wire to the BLACK supply wire from the outlet box using a wire connector (BB).

Connect the fixture ground wire and supply ground wire using a wire connector (BB) or by fastening to the ground screw on the round mounting plate.

Push all wire connections carefully into the outlet box.

Diagram Description: Illustrates wire connections: fixture's white wire to supply's white wire, fixture's black wire to supply's black wire, and fixture's ground wire to supply's ground wire, all secured with wire connectors (BB). A separate diagram shows the ground wire connection to the green ground screw.

Step 4: Secure Fixture

Slide the mounting holes in the fixture (A) over the screws (AA) and using the cylinder nuts (EE), tighten the fixture against the mounting surface.

Diagram Description: Shows the fixture (A) being mounted onto the screws (AA) protruding from the mounting plate, and then secured using cylinder nuts (EE). It notes that mounting can be oriented up or down.

Step 5: Attach Glass Shades

Attach the glass shades (B) to the fixture (A) and use the socket rings (C) to secure them modestly tight.

Diagram Description: Shows glass shades (B) being fitted onto the fixture sockets and then secured with socket rings (C).

Step 6: Install Bulbs

Thread the lamps (not included) into the fixture sockets. Use 100-watt MAX incandescent medium base lamp, SBCFL or SBLED.

Diagram Description: Shows a light bulb being screwed into a fixture socket.

Warranty Information

WARRANTY AND EXCLUSIVE REMEDY: Progress products, when properly installed and under normal conditions of use, are warranted to our customers only to be free from defects in material and workmanship at time of shipment. All warranty claims must be asserted within one year from date of purchase of the subject items; thereafter, warranty claims will not be honored. Customers' sole remedy for a warranty claim or otherwise shall be limited to repair or replacement of the subject product if it is shown to have been defective in material or workmanship at time of shipment. Progress's sole and maximum liability for a defective product shall never exceed the cost of the subject product. EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANTY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS. Therefore, the customer's sole and exclusive remedy against us for breach of the warranty, breach of contract or negligence or strict liability or otherwise shall be limited to repair or replacement of the subject product at our option (excluding installation and removal charges which shall not be our liability) or, if we choose, refund of the purchase price. In no case does our warranty and exclusive remedy extend to anybody other than our customers. Our customers are not authorized to extend warranties or remedies on our behalf to anyone. Such unauthorized extensions of warranties or remedies by the customer shall remain customer's responsibility. Customer is responsible for determining the suitability of our products for customer's use or resale, or for incorporating them into objects or for applications which customer designs, assembles, constructs or manufactures.

Additional Information

The original document also contains assembly and installation instructions in French.