Progress Lighting P500445 3-LT FOYER Installation Guide
Model: P500445
Collection: Pinellas
Package Contents
| Part | Description | Quantity |
|---|---|---|
| A | Fixture | 1 |
| B | Glass Shade | 3 |
| C | Socket Cover | 3 |
| D | Black Socket Ring | 3 |
| E | Canopy | 1 |
Hardware Contents (Not Actual Size)
| Part | Description | Quantity |
|---|---|---|
| AA | Screw (#8-32) | 2 |
| BB | Wire Nut | 3 |
| CC | Round Mounting Plate | 1 |
| DD | Hex Nut (#8-32) | 2 |
| EE | Cylinder Nut (#8-32) | 2 |
| FF | 12" Pipe (1/8IP) | 4 |
| GG | 6" Pipe (1/8IP) | 4 |
| HH | Nipple (1/8IP) | 1 |
Safety Information
CAUTION: Read and understand this entire manual before attempting to assemble, operate, or install the product.
CAUTION: Read instructions carefully and turn electricity off at the main circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Use minimum 90°C supply conductors. Consult a qualified electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.
French Safety Note: Mise en garde: Lire les instructions avec soin et couper le courant au disjoncteur central avant de commencer l'installation. Risque d'incendie. Min 90°C conducteurs d'alimentation. Consulter un électricien qualifié. Le verre est toujours fragile; maniez le(s) composant(s) et/ou l' (les) ampoule(s) avec prudence.
Spanish Safety Note: Precaución: Lea cuidadosamente las instrucciones y desconecte la electricidad del cortacircuitos principal antes de iniciar la instalación. Riesgo de fuego. Min. 90°C los cables de suministro. Consulte a un electricista calificado. El vidrio es frágil; tenga cuidado al manipular el (los) elemento(s) de vidrio y/o la(s) bombilla(s).
Preparation
- Before beginning installation, ensure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install, or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off the main power supply before cleaning the product or changing light bulbs. To clean, wipe with a damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
Step 1: Prepare Mounting Plate and Outlet Box
Loosely thread the screws (AA) and hex nuts (DD) onto the round mounting plate (CC) as shown. Adjust the screw length according to the fixture canopy depth.
Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.
Lift the fixture and pass the screws (AA) through the two mounting holes in the fixture canopy. While holding the fixture, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16" [5mm] of threads are showing. This should be enough to mount the fixture.
Next, take the fixture down and tighten the hex nuts (DD) up against the round mounting strap (CC) to secure the correct thread length for mounting.
Diagram Description: Diagram shows the round mounting plate (CC) with screws (AA) and hex nuts (DD) attached. An inset shows an 'INCORRECT' and 'CORRECT' illustration of how the screws should be threaded through the mounting plate and canopy, indicating that 3/16" [5mm] of thread should be visible for proper attachment. It also shows tightening the hex nuts against the mounting strap.
Step 2: Install Fixture Stem and Canopy
Determine the hanging length of your fixture by adding or removing stems. The electrical and ground wires may also optionally be cut to length, but leave at least 6 inches minimum of wire past the canopy (E) 90° swivel to allow for easy connections.
Pass wires through the four pipe sections (FF, HH, GG), tightening the stem assembly to the fixture (A) as you go to avoid twisting the wires. Pass wires through the canopy (E). Tighten the 90° swivel of the canopy (E) to the stem assembly.
Diagram Description: Diagram illustrates the assembly of the fixture's stem, showing multiple pipe sections (FF, HH, GG) being connected. Electrical wires and a ground wire are shown passing through these pipes and into the canopy (E). The 90° swivel mechanism of the canopy is also depicted.
Step 3: Connect Wiring
Strip 3/8" of insulation from the electrical wire ends.
Using wire nuts (BB), connect the RIBBED fixture wire to the WHITE supply wire from the outlet box. Connect the SMOOTH fixture wire to the BLACK supply wire.
Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.
Diagram Description: Diagram shows the wiring connections. It depicts the ribbed fixture wire being connected to the white supply wire with a wire nut (BB). The smooth fixture wire is shown connected to the black supply wire with another wire nut. The ground wires (bare copper or green) are shown connected together with a wire nut or to the green ground screw on the mounting plate.
Step 4: Secure Canopy
Secure the canopy (E) to screws (AA) using the two cylinder nuts (EE) to secure tightly.
Diagram Description: Diagram shows the fixture canopy (E) being attached to the mounting screws (AA) using the cylinder nuts (EE).
Step 5: Attach Glass Shades
Attach the glass shades (B) to the fixture (A). Use the socket covers (C) and the black socket rings (D) to secure modestly tight.
Diagram Description: Diagram illustrates the glass shades (B) being attached to the fixture (A). Socket covers (C) and black socket rings (D) are shown being used to secure the shades.
Step 6: Install Lamps
Thread the lamps (not included) into the fixture sockets. Use 60-watt MAX incandescent candelabra base lamp, SBCFL or SBLED.
Diagram Description: Diagram shows light bulbs being screwed into the fixture's sockets.
Warranty Information
Progress Lighting products are warranted to be free from defects in material and workmanship at the time of shipment when properly installed and used under normal conditions. All warranty claims must be asserted within one year from the date of purchase. The customer's sole remedy for a warranty claim shall be limited to repair or replacement of the product if it is shown to have been defective. Progress's liability shall never exceed the cost of the product. All other warranties, express or implied, including warranties of merchantability and fitness for a particular purpose, are disclaimed. Progress is not liable for any incidental or consequential damages.
Customer Support
For questions regarding product information, assembly, or missing parts, please contact Progress Lighting:
Phone: 800-447-0573 (8am-8pm Eastern, Monday-Friday)
Email: customerservice@progresslighting.com
