Progress Lighting P710126 Boundary 2-Light Wall Bracket
Model Number: P710126
Package Contents
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Fixture | 1 |
Hardware Contents (not actual size)
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| AA | Screw (#8-32) | Qty:2 |
| BB | Wire Nut | Qty:3 |
| CC | Round Mounting Plate | Qty:1 |
| DD | Hex Nut (#8-32) | Qty:2 |
| EE | Cylinder nut (#8-32) | Qty:2 |
Support
We can assist you with questions regarding product information, assembly or missing parts.
? 800-447-0573 (8am-8pm Eastern, Monday-Friday)
✉️ customerservice@progresslighting.com
Safety Information
Please read and understand this entire manual before attempting to assemble, operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
-
Step 1: Prepare Mounting Plate
Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC). Adjust the screw length according to the fixture canopy depth.
Diagram Description: The round mounting plate (CC) is shown with screws (AA) and hex nuts (DD). The hex nuts (DD) are threaded onto the screws (AA) which pass through the plate (CC). The screws (AA) are then adjusted so that approximately 3/16" [5mm] of thread is showing, which is the correct length for mounting the fixture canopy.
-
Step 2: Attach Assembly to Outlet Box
Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.
Lift up the fixture to the mounting surface and pass the screws (AA) through the two mounting holes in the fixture canopy. While holding the fixture, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16" of threads are showing. This ensures the correct length for mounting.
Next, take the fixture down and tighten the hex nuts (DD) up against the round mounting plate (CC). This secures the screw length.
Diagram Description: The assembled mounting plate (CC) with adjusted screws (AA) and hex nuts (DD) is shown being attached to an electrical outlet box. The screws (AA) are depicted protruding from the mounting surface, ready to receive the fixture canopy.
-
Step 3: Wiring Connections
Strip 3/8" of insulation from the electrical wire ends.
Using wire nuts (BB), connect the WHITE fixture wire to the WHITE supply wire from the outlet box. Connect the BLACK fixture wire to the BLACK supply wire from the outlet box.
Connect the fixture ground wire (bare copper or green) and the supply ground wire using a wire nut (BB) or by fastening to the ground screw on the round mounting plate. Push all wire connections carefully into the outlet box.
Diagram Description: Illustrates electrical wiring connections. The white fixture wire is connected to the white supply wire using a wire nut (BB). The black fixture wire is connected to the black supply wire using a wire nut (BB). The fixture's ground wire (bare copper or green) is connected to the supply ground wire using a wire nut (BB) or fastened to the ground screw on the mounting plate. All connections are shown being routed into the outlet box.
-
Step 4: Mount Fixture
Slide the mounting holes in the fixture (A) over the screws (AA) and using the cylinder nuts (EE), tighten the fixture against the mounting surface.
Diagram Description: The fixture (A) is shown being mounted. The fixture's mounting holes are aligned with the protruding screws (AA). Cylinder nuts (EE) are used to secure the fixture (A) to the mounting surface by tightening onto the screws (AA).
-
Step 5: Install Lamps
Thread the lamps (not included) into the fixture sockets. Use 60-watt MAX incandescent medium base lamp, SBCFL or SBLED.
Warranty Information
Progress products, when properly installed and under normal conditions of use, are warranted to be free from defects in material and workmanship at time of shipment. All warranty claims must be asserted within one year from date of purchase of the subject items; thereafter, warranty claims will not be honored. Customers' sole remedy for a warranty claim or otherwise shall be limited to repair or replacement of the subject product if it is shown to have been defective in material or workmanship at time of shipment. Progress's sole and maximum liability for a defective product shall never exceed the cost of the subject product.
Except for the stated warranty and exclusive remedy, Progress disclaims all other warranties, whether express or implied, and specifically disclaims the implied warranties of merchantability and fitness for a particular purpose.
In no event shall Progress be liable to the customer for any damages, whether incidental or consequential, which are alleged to be caused by one or more of Progress products, beyond the cost to the customer of the subject product or products. Therefore, the customer's sole and exclusive remedy against Progress for breach of warranty, breach of contract, negligence, strict liability, or otherwise shall be limited to repair or replacement of the subject product at Progress's option (excluding installation and removal charges), or if Progress chooses, refund of the purchase price.
This warranty and exclusive remedy extend only to Progress's customers. Customers are not authorized to extend warranties or remedies on behalf of Progress. Such unauthorized extensions of warranties or remedies by the customer shall remain customer's responsibility.
Customer is responsible for determining the suitability of our products for customer's use or resale, or for incorporating them into objects or applications which customer designs, assembles, constructs or manufactures.
