Baby Trend SS66XXX Sit-N-Stand Ultra Stroller: Instruction Manual

Warranty and Contact Information

Warranty: Baby Trend® warrants this product against workmanship defects for one year from the date of purchase. This warranty is void if the product has been misused, abused, improperly assembled, subjected to excessive wear and tear, altered, or if the serial number has been removed. Any property damage during installation is the sole responsibility of the end user.

Customer Service: For replacement parts, service, or repair, please contact Baby Trend® Customer Service Department at 1 (800) 328-7363, Monday through Friday, between 8:00 a.m. and 4:30 p.m. (PST). Return Authorizations are required for all returns.

For complete warranty details, visit: babytrend.com/pages/limited-warranty

Company Address: Baby Trend, Inc., 13048 Valley Blvd., Fontana CA 92335

Website: www.babytrend.com

Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.

Important Safety Warnings

⚠️ WARNING: Always follow all instructions to ensure your child's safety. Failure to do so could result in serious injury or death. Always use the safety harness and ensure children are properly positioned.

⚠️ WARNING: Never leave children unattended. Items like purses, shopping bags, or diaper bags can alter the stroller's balance, creating a hazardous condition.

Weight Limits:

• Front/Rear Stroller Seat: Child must be at least 6 months old and not over 40 inches (102 cm) tall. Maximum weight: 40 lbs (18.1 kg) per seat. Exceeding 40 lbs per child may cause excessive wear and stress.
• Storage Basket: Maximum weight 5 lb (2.26 kg).
• Parent Tray & Child Tray: Maximum weight 3 lb (1.36 kg) each.
• Seat Belt Storage Pocket: Maximum weight 1 lb (0.45 kg) for seat belt storage only.
• Front Seat Maximum Weight: 50 lb (22.7 kg).
• Platform and Jump/Rear Seat Maximum Weight: 50 lb (22.7 kg).
• Rear Platform/Jump Seat: Child must be at least 2 1/2 years old and not over 40 inches (101.6 cm) tall. Total child weight exceeding 110 lbs (49.89 kg) may cause excessive wear and stress.

⚠️ WARNING: Ensure the stroller is fully opened and locked before allowing a child near it.

⚠️ WARNING: NEVER use the stroller on stairways or escalators.

⚠️ WARNING: NEVER allow your stroller to be used as a toy.

Cleaning: Use only mild household soap or detergent with warm water on a sponge or clean cloth.

Maintenance: Regularly check for loose screws, worn parts, torn material, or stitching. Replace or repair parts as needed. Discontinue use if the stroller malfunctions or is damaged and contact customer service.

Parts Identification

Before assembling, verify you have all parts for this model:

• Front Canopy
• Stroller Frame
• Cup Holders (x2)
• Child Tray
• Parent Tray
• Front Wheel*
• Rear Axle*

*Wheel styles may vary.

Assembly Instructions

Front Wheels

To attach front wheels: Lean the stroller back so it rests on the handle with front and rear legs pointing upward. Position front wheels over the front leg tubes, aligning the housing hole with the legs. Push down firmly until wheels lock securely. Tug each wheel to confirm attachment.

(Diagram reference: Figure 1a shows unlocking the fold latch. Figure 1b shows unfolding the frame by sliding the thumb trigger and pulling the handle. Figure 1c illustrates attaching front wheels by aligning housing with leg tubes.)

Rear Wheels

Position the rear axle over the rear leg tubes with brake pedals facing backward. Push down equally on both sides until they lock into place. (Diagram reference: Figure 2 shows this process.)

⚠️ NOTE: NEVER use the stroller if wheels do not lock into place. Contact customer service if assistance is needed.

Foot Rest

Push the foot rest downward until it snaps onto the U-shaped frame cross member. (Diagram reference: Figure 3 shows this action.)

Child Tray

To attach: Push the tray downward onto each side of the front armrests until both sides snap into place. Ensure it is securely latched. (Diagram reference: Figure 4 illustrates attaching the child tray.)

⚠️ WARNING: The child's tray is not a restraint device. Always secure your child with the seat belt. DO NOT lift the stroller by the child's tray. Use caution when attaching the tray with a child in the stroller.

To access the child seat: Pull one side of the release lever located on the underside of the child tray and lift upward. This allows the tray to lift and rotate out of the way. (Diagram reference: Figures 5a and 5b show the release lever and seat access.)

Child Tray Rotation and Removal

To rotate the child tray to a vertical position for infant car seat attachment: Press buttons on both sides of the tray to rotate it down 90 degrees. (Diagram reference: Figure 6 shows this rotation.)

To remove the child tray: Pull both release levers on the underside of the tray and lift upward. (Diagram reference: Figure 7 illustrates tray removal.)

NOTE: The canopy is only needed for the seated position, not with an infant car seat.

Cup Holders

To attach cup holders: Push them downward onto each side of the armrests until they snap into place. To remove, pull the release lever on the underside of the cup holder. (Diagram reference: Figure 8 shows cup holder attachment.)

Canopy

To attach the canopy: Align the male fittings on the canopy with the slots on the armrest and push both fittings downward until snapped into place. (Diagram reference: Figure 9 shows canopy attachment.)

To open the canopy, push forward on the front edge while holding the rear in place. To close, pull backward on the front edge. To remove, press the snap button under the armrest and pull to release the fitting from the slot. Repeat for the other side. (Diagram reference: Figure 9b shows canopy removal.)

Parent Tray

To attach the parent tray: Position the tray with hinges facing forward. Snap the parent tray to the stand at the top of the frame. Ensure it is securely latched. (Diagram reference: Figure 10 illustrates parent tray attachment.)

Safety Instructions

Brakes

⚠️ WARNING: Always set brakes when the stroller is not being pushed to prevent it from rolling away. Never leave the stroller unattended on an incline.

To engage brakes: Apply light downward pressure to the brake lever on each rear wheel. You may need to move the stroller slightly forward or backward to align the brake teeth with the wheel brake cluster. (Diagram reference: Figure 11a shows brake engagement.)

NOTE: Verify the stroller does not move and both brakes are properly applied.

To release brakes: Gently lift up on the brake lever. (Diagram reference: Figure 11b shows brake release.)

Securing the Child (5-Point Harness)

⚠️ WARNING: Avoid serious injury from falling or sliding out. Always use the safety harness.

⚠️ STRANGULATION HAZARD: Child can strangle in loose straps. Never leave a child in the seat with loose or undone straps.

The 5-point harness has two attachment positions for the shoulder straps. Select the position that places the shoulder strap level with or below the child's shoulder. Feed the shoulder harness under the correct loop. To adjust harness slot, unhook the shoulder strap from the crotch buckle. Feed the strap through the harness spread slots (accessible from the seat's rear) and reattach to the crotch buckle. (Diagram reference: Figure 12a shows harness adjustment.)

Place the child in the stroller seat. Bring the safety harness around the child's waist and over the shoulders. Place the crotch strap between the child's legs. Insert the male ends of the shoulder/waist belts into the crotch strap buckle. Tighten the harness to be snug around the child's waist and over the shoulders. (Diagram reference: Figure 12b illustrates securing the child.)

To release harness: Push the button on the center clasp; the two harness buckles will pop free. (Diagram reference: Figure 13 shows harness release.)

NOTE: Buckles may be difficult to release when first used.

Car Seat Safety Belt

Strap the safety belt over the infant car seat, threading it through the seat belt slots on the car seat. Connect the buckles. (Diagram reference: Figure 14a shows this process.) The safety belts are located in small pockets on the outer sides of the seat pads. (Diagram reference: Figure 14b shows storage pockets.) Tighten the strap so the infant car seat fits snugly and cannot move. It is crucial that the infant car seat strap is always tightly fastened around the car seat.

NOTE: When the stand feature safety belt is not in use, store it properly.

Platform Safety Belt

The stroller is equipped with a safety belt for the platform. Always secure the stand feature safety belt behind the child and engage the buckle when using the platform. (Diagram reference: Figure 15a shows platform belt use.)

To release: Apply pressure to both sides of each male clip until released. This requires moderate effort to prevent accidental release. (Diagram reference: Figure 15b shows release mechanism.)

Operation Instructions

Reclining Seats

⚠️ WARNING: The upright position should be used only for a child at least 6 months old.

The front seat has two recline positions. To recline the seat, rotate the recline bar and press backward on the seat back. To return to the upright position, press upward on the seat back while rotating the recline bar. (Diagram reference: Figure 16 illustrates seat recline.)

Attaching Infant Car Seat

⚠️ WARNING: This stroller is NOT compatible with any ALLY Car Seats.

⚠️ WARNING: Always use the safety belt to secure the front car seats to avoid serious injury from falling.

Infant car seats are sold separately. Visit babytrend.com for a compatibility chart.

ATTENTION: The infant car seat may only be attached to the front seat of the stroller.

To attach the infant car seat in the front seating position: Attach the child tray in the front seating position and rotate it to the vertical position. Place the seat in the reclined position (refer to Figure 16). Set the infant car seat facing toward the rear of the stroller so the seat shell fits into the child tray and latches securely. (Diagram reference: Figure 17 shows infant car seat attachment.)

To remove the Infant Car Seat: Squeeze the release handle at the foot-end of the seat and carefully lift upward. (Diagram reference: Figure 18 shows car seat removal.)

Jump Seat

⚠️ WARNING: The rear platform and jump seat are designed for children at least 2 1/2 years old with good balance and coordination, not exceeding 40 inches in height.

To use the jump seat, remove the child tray if attached. Refer to page 9 for instructions on removing the rear child tray.

Sitting on Jump Seat

Have the child sit on the jump seat facing backward. Secure the child with the jump seat 3-point harness. Part of the harness is stored in a pocket on the back of the front seat. Place the seat belt around the child's waist and buckle it to the crotch strap. Adjust the seat belt to be snug. (Diagram reference: Figure 19a shows child on jump seat.)

RELEASE! Push the button on the center clasp to release all harness straps. (Diagram reference: Figure 19b shows harness release.)

Standing on the Platform

Position the child on the rear platform, facing forward, ensuring they are standing securely and holding the frame. Secure the stand feature safety belt behind the child and engage the buckle. (Diagram reference: Figure 20 shows platform use.)

To release, refer to step 15.

NOTE: Ensure the child's feet are fully on the platform at all times.

Folding Instructions

⚠️ WARNING: Be careful when folding and unfolding to prevent finger entrapment.

CAUTION: Keep children away from the stroller while folding.

1. Close the canopy as described previously.

2. Pull the stroller backward several inches to rotate the front wheels forward. (Diagram reference: Figure 21a shows wheel rotation.)

3. To fold: Slide the fold lock with your thumb while squeezing the large fold button on the handle. Push forward on the handle. (Diagram reference: Figure 21b shows the folding mechanism.)

4. Once folding begins, release the handle and continue pushing forward until the stroller is folded. Lock the fold latch. (Diagram reference: Figure 21c shows the locked folded stroller.)

Maintenance and Care

Seat Pad

To clean the seat pad, use mild household soap or detergent and warm water on a sponge or clean cloth.

General Maintenance

Regularly check for loose screws, worn parts, torn material, or stitching. Replace or repair parts as needed.

Baby Trend Customer Service

The Customer Service Department can be contacted at 1 (800) 328-7363, Monday through Friday, between 8:00 a.m. and 4:30 p.m. (PST). Return Authorizations are required prior to returning any product(s) to Baby Trend®.