Baby Trend Sit N Stand Plus Stroller - Model #7548

Important Safety Information

WARNING: Please follow all of these instructions to ensure the safety of your child. Keep these instructions for future reference.

WARNING: Failure to follow these instructions could result in serious injury or death. Avoid serious injury from falling or sliding out. Always use the safety belts and ensure that the children are properly positioned according to these instructions.

WARNING: Never leave children unattended.

• Maximum weight in Parent Tray: 3 lbs. Excessive weight may cause a hazardous unstable condition.
• Purses, shopping bags, parcels, diaper bags or accessory items may change the balance of the stroller and cause hazardous unstable conditions.
• Maximum weight in basket: 5 lbs. Excessive weight may cause a hazardous unstable condition.
• Ensure stroller is fully erect and latched in the open position before allowing children near.
• The rear stand-on platform is designed for a child who is at least 2.5 years old and not over 40 inches tall.
• Use of the stroller with two children weighing more than 40 pounds each, or children totaling more than 80 pounds, will cause excessive wear and stress and may cause a hazardous unstable condition.
• DO NOT use on stairways or escalators.
• Never allow your stroller to be used as a toy.
• Cleaning: Use only mild household soap or detergent and warm water on a sponge or clean cloth.
• Regularly check stroller for loose screws, worn parts, torn material, or stitching. Replace or repair parts as needed.
• Discontinue use of stroller if it malfunctions or becomes damaged. Contact customer service for parts/repair.

Parts Identification

The stroller includes the following parts:

• Parent Tray
• Child Tray
• Front Wheels
• Rear Wheels
• Stroller Frame
• Front/Rear Canopies
• Snap N Go Attachment Bar
• Foot Rest

[Diagram showing the location of each part: Parent Tray, Child Tray, Front Wheels, Rear Wheels, Stroller Frame, Front/Rear Canopies, Snap N Go Attachment Bar, Foot Rest.]

Assembly Instructions

TO ENSURE SAFE OPERATION OF YOUR STROLLER, PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

1. Remove stroller from box. The front wheels, rear wheels, child tray, and canopies need to be installed prior to use.
2. Attach Front Wheels: Unfold stroller. Lean it backward so it rests on the handle and rear frame tubes with front wheel tubes pointing upward. Position the front wheel assembly at the front tube, aligning the large hole in the swivel assembly with the tube. Push each front wheel assembly onto the front tube, ensuring the wheel assembly locks onto the front leg. Pull on the wheel assembly to confirm secure attachment. [Figures 1 & 2 illustrate this process.]
3. Attach Rear Wheels: Lean stroller forward to rest on the front wheels. Position the rear axle and wheel assembly so the brake levers face the rear. Press the rear wheel assembly onto the rear frame tubes, ensuring the push buttons on the forward side of each rear tube engage the hole on the forward side of each rear wheel housing. Pull on the rear wheel assembly to confirm secure attachment. [Figure 3 illustrates this process.]
4. Ensure wheels are firmly locked into place. Do NOT use the stroller if wheels are not locked. Contact customer service immediately for assistance.
5. Attach Footrest: Snap footrest onto front legs of stroller just below the seat. Push downward on the footrest until it locks onto the rivets protruding from both sides of each leg and snaps onto the U-shaped frame cross member. [Figure 4 illustrates this process.]
6. Attach Front Child Tray: Push the tray onto the front frame tube, aligning it between the protruding rivets. Push backward on the latch until snapped into place. The protruding rivets should be between the tray latch. Check that the tray is securely latched. [Figures 5 & 6 illustrate this process.]
7. Remove Front Child Tray: Pull outward on the latches and pull outward on the tray. One end may be attached or removed at a time. [Figure 7 illustrates this process.]
8. WARNING: The child's tray is not a restraint device: always secure your child with the seat belt. DO NOT lift the stroller by the child's tray. Use care when attaching the child's tray on the stroller with a child in the stroller.
9. Attach Front Canopy: Line up the male fittings on the canopy with the female fittings on the armrest and push both fittings downward until snapped into place. Push forward on the front edge of the canopy to open. [Figure 8 illustrates this process.]
10. Attach Rear Canopy: Line up the female fittings of the canopy with the male fittings on the handle frame tube and push downward. [Figure 9 illustrates this process.]
11. Remove Rear Canopy: Reverse installation steps and pull up to remove. [Figure 9A illustrates this process.]
12. Remove Front Canopy: Depress the plastic attachment and pull upward to remove. [Figure 9B illustrates this process.]

Securing Children

WARNING: Avoid serious injury from falling or sliding out. Always use the seat belt.

Securing Front/Rear Sitting Children

1. The 5-point harness has 2 attachment positions. Select the loop position that places the shoulder strap level with, or below, the top of the child's shoulder and feed the shoulder harness under the correct loop. [Figure 10 illustrates harness positions.]
2. Carefully place the child in the stroller seat and bring the safety harness around the child's waist and over the shoulders. Place the crotch strap between the child's legs. Insert the male end of each shoulder/waist belt into the buckle on the crotch strap. Tighten the harness to be snug around the child's waist and over the child's shoulders. [Figure 11 illustrates tightening the harness.]
3. Releasing Harness: Apply pressure to both sides of each male clip until the clip is released. This process requires a moderate amount of effort to prevent accidental release by your child. Note: Buckles may be hard to release when first used.

Securing Rear Standing Child

The rear platform and jump seat are designed for a child who is at least 2.5 years old, has good balance and coordination, and is not over 40 inches tall.

1. Position the child on the platform on the back of the stroller. Be sure the child is facing forward and hands are holding the frame. Secure the safety belt behind the child and engage buckle. Ensure the child's feet are fully on the platform at all times. [Figure 12 illustrates positioning.]
2. IMPORTANT NOTE: When using the rear SEAT, you must put the STAND FEATURE SAFETY BELT in the storage location located on the rear of the seat. [Figure 12A illustrates storage location.]
3. WARNING: To avoid a possible choking hazard when using the rear seat, put the STAND FEATURE SAFETY BELT in the storage location on the rear of the seat.

To Use Jump Seat

1. Have child sit on the jump seat facing backwards. Secure the seat belt, which is attached to the back of the seat, around the child's waist, and buckle to the crotch strap. Adjust the seat belt to be snug around the child's waist. [Figure 12B illustrates jump seat use.]
2. Releasing Harness: Apply pressure to both sides of the male clip until the clip is released. This process requires a moderate amount of effort to prevent accidental release by your child.
3. Be sure that the child's feet are fully on the platform at all times.

Seat Reclining and Removal

To Recline Seats

1. The front seat has a two-position recline. To recline the seat, rotate the recline bar and press backward on the seat back. To place the seat in the upright position, press upward on the seat back while rotating the recline bar. [Figure 13 illustrates front seat recline.]
2. The upright position should be used only for a child that is at least 6 months old. Note: Seat does not fully recline.
3. Rear Seat: Locate the plastic adjuster and squeeze the ends. Loosen or tighten the strap to your desired recline position. [Figure 14 illustrates rear seat recline.]

To Remove Rear Seat

1. Remove the rear canopy. Locate the rear seat attachment positions. Unhook the fabric from the tabs on the stroller handle frame. Repeat for the opposite side. Also, unsnap the footrest fabric. To completely remove rear seat fabric, unhook the D-Ring from the rear jump seat, and remove the 2 D-Rings from the rear seat. [Figures 15, 15A, 15B, 15C illustrate rear seat removal.]
2. To remove the lower portion of the rear seat fabric, locate the two attachment positions. Unhook the fabric from the tab on the lower frame tube, then release the front snap located on the same lower frame tube. [Figures 16 & 16A illustrate lower rear seat fabric removal.]
3. When you are not using the jump seat harness, place it in the storage location on the rear of the front seat. [Figure 16A illustrates harness storage.]

Brakes, Canopies, and Folding

Brakes

WARNING: Always set brakes when the stroller is not being pushed so that the stroller will not roll away. Never leave stroller unattended on a hill or incline as the stroller may slide down the hill.

1. Engage Brakes: Apply light downward pressure to the brake lever located on each rear wheel. The stroller may require slight forward or rearward movement to align the teeth on the brake with each wheel brake cluster. Check that the stroller will not move and that the brakes are properly applied. [Figures 17 & 18 illustrate brake operation.]
2. Release Brakes: Gently lift up on the brake lever.

Canopies

1. Open Canopies: Push forward on the front frame of the canopies.
2. Close Canopies: Pull the front edge toward the rear of the stroller until folded. Always fold the canopies prior to folding the stroller frame. [Figure 19 illustrates canopy folding.]
3. The canopies will ratchet forward or back to block the sun. Pull forward on the front canopy frame tube to move forward. Pull backward on the rear frame tube to move back.

To Remove Front Child Tray

1. To remove front child tray, pull forward on the locking lever on the tray arms to unlock. The tray may be released on either side and will swing away for easy access to your child. [Figure 7 illustrates tray removal.]

To Fold Stroller

Do Not allow children near stroller while folding.

1. Close the canopies as described above. Ratchet the front canopy all the way back. [Figure 20 illustrates canopy position for folding.]
2. Unbuckle rear standing safety belt. [Figure 12 referenced.]
3. Fold Mechanism: Slide the red fold latch safety button in the center of the handle and squeeze the red handle while pushing forward on the handle. Once the stroller begins to fold, release the red handle and pull upward on the child tray until the stroller is folded. [Figure 21 illustrates folding mechanism.]
4. Secure Folded Stroller: Latch the fold latch, located on the right side of the stroller handle, over the extended rivet on the armrest. You may have to rotate the front wheels to fold the stroller completely. [Figure 22 illustrates securing the folded stroller.]

Unfolding and Car Seat Attachment

To Unfold Stroller

Do Not allow children near stroller while unfolding.

1. Release the folding latch, which is located on the right side. [Figure 22 referenced.]
2. Lift up on the stroller handle with both hands until the stroller frame is erect and locked in the open position. The stroller has spring-loaded latches on both sides of the frame. Test that both latches are fully engaged prior to placing your child in the stroller.

To Attach an Infant Car Seat

WARNING: Avoid serious injury from falling. Do Not use the Snap N Go bar if it is not securely locked onto both sides of the stroller.

1. Recline the front seat back. Remove the child tray.
2. Slide Snap N Go attachment bar into the female slots located on the frame tube. Make sure the snap n go attachment bar locks in place before attaching the car seat. [Figure 23 illustrates attachment bar insertion.]
3. Place car seat onto the front bar. [Figure 24 illustrates car seat placement.]
4. IMPORTANT NOTE: Most brands of infant car seats will lock onto the front bar, and some brands may simply rest on the front bar. FOR SAFE OPERATION, IT IS VERY IMPORTANT THAT THE CAR SEAT STRAP IS ALWAYS TIGHTLY FASTENED AROUND THE CAR SEAT.
5. Strap the vehicle's safety belt over the car seat and through the seat belt slots on your car seat, connect the buckles together. Tighten the strap so the car seat fits snug and can't move. Check that the car seat is secure before using the stroller. [Figure 24 illustrates securing the car seat.]

? STOP ?

IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT, PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT (800) 328-7363 BETWEEN THE HOURS OF 8:00AM AND 4:30PM PACIFIC COAST TIME FOR ASSISTANCE.