Aurora Lumi-Fit Fixed LED Downlight

Introduction

This document provides essential information for the safe and correct installation and operation of the Aurora Lumi-Fit Fixed LED Downlight. Please read all instructions carefully before proceeding.

Safety Precautions

Important: Always ensure the power supply is switched OFF at the mains before commencing any electrical work. Failure to do so could result in electric shock. [Warning symbol: ⚡️ OFF]

• Installation should be carried out by a qualified electrician in accordance with current wiring regulations.
• Ensure the mains voltage matches the product's voltage requirements.
• This product is designed for indoor use only.
• Do not install near flammable materials.
• Ensure adequate ventilation around the fitting.
• The product must be earthed.
• If the flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similarly qualified person in order to avoid a hazard.

Package Contents

Verify that all components are present:

• 1 x Aurora Lumi-Fit Fixed LED Downlight
• 1 x LED Driver
• 1 x User Manual (this document)

[Check all parts before installation.]

Technical Specifications

General:

[Note: Specific technical details like CCT, IP rating, dimmability, and dimensions are placeholders and should be verified from the actual product.]

Installation Instructions

Tools Required: Screwdriver, Wire Strippers, Wire Cutters, Measuring Tape, Pencil, Safety Glasses, Insulation Tape.

1. Preparation

   Step 1: Power Off
   Ensure the main power supply to the installation area is switched OFF at the circuit breaker. Verify power is off using a voltage tester. [Warning symbol: ⚡️ OFF]

   Step 2: Ceiling Cut-out
   Determine the desired location for the downlight. Using the provided template (if available) or the product's cut-out diameter specification, mark the ceiling. Carefully cut a hole in the ceiling using appropriate tools. Ensure no electrical wires or pipes are present in the cutting area. [Diagram description: A circular hole is cut into a ceiling surface.]

2. Wiring

   Step 3: Connect Driver
   Connect the LED driver to the mains supply (Live, Neutral, Earth). Connect the output cable from the LED driver to the downlight's connector. Ensure all connections are secure and correctly polarized. [Diagram description: The LED driver has input terminals for mains L, N, E and output terminals for the downlight. Wires are shown connecting to corresponding terminals.]

   Step 4: Earth Connection
   Connect the earth wire from the mains supply to the earth terminal on the downlight fitting and/or driver, as indicated. This is crucial for safety. [Symbol: Earth symbol ⏚]

3. Fitting the Downlight

   Step 5: Insert Downlight
   Gently push the downlight fitting into the prepared ceiling cut-out. Ensure the spring clips (if present) engage securely with the ceiling material. [Diagram description: The downlight unit is being pushed into the ceiling hole, with spring clips visible.]

   Step 6: Secure the Fitting
   Ensure the downlight is firmly seated and flush with the ceiling surface. Check that no wires are trapped.

4. Final Steps

   Step 7: Power On
   Once installation is complete and all connections are verified, switch the main power supply back ON at the circuit breaker. Test the downlight.

   Step 8: Disposal
   Dispose of old or faulty electrical equipment responsibly according to local regulations. [Symbol: Recycling symbol ♻️]

Maintenance and Care

Cleaning:

• Ensure the power is switched OFF before cleaning.
• Wipe the luminaire with a soft, dry cloth. Do not use abrasive cleaners or solvents.

Troubleshooting:

• Light does not turn on: Check power supply, connections, and ensure the driver is correctly connected.
• Flickering: Ensure connections are secure and the driver is compatible if dimmable.

[If problems persist, consult a qualified electrician.]

Warranty Information

This product is guaranteed for a period of 3 years from the date of purchase. The warranty is not valid in case of misuse or improper installation. Please refer to the retailer for warranty claims.

[Note: The original metadata mentioned French text regarding warranty: "Ce produit est garanti pour une période de 3 ans à partir de la date d'achat. La garantie n'est pas valable dans le cas d'une mauvaise utilisation ou." This has been translated and incorporated.]