Hooke Road Front Bumper BXG.8007
Installation Instructions
ATTENTION: Please verify all parts are present and read instructions carefully before starting installation. Please feel free to contact your distributor if you have any kind of question about your purchase.
Contents
Parts Identification
Diagram showing components: A1, A2, A3 labeled as Bull Bar; B labeled as Main Body; C1, C2 labeled as Wings; D labeled as License Plate Bracket; E labeled as Winch Power Control Box Bracket.
| Qty | Part Name | Size(mm) | Picture |
|---|---|---|---|
| 4 | Hex Bolt | M12×35 | [Bolt] |
| 6 | Hex Bolt | M12×30 | [Bolt] |
| 10 | Hex Bolt | M8×20 | [Bolt] |
| 2 | Button Bolt | M6×16 | [Bolt] |
| 10 | Split Lock Washer | D12 | [Split Washer] |
| 10 | Split Lock Washer | D8 | [Split Washer] |
| 14 | Flat Washer | M12×30×2 | [Flat Washer] |
| 10 | Flat Washer | M8×16×1 | [Flat Washer] |
| 2 | Flat Washer | M6×12×1 | [Flat Washer] |
| 10 | Hex Nut | M12 | [Nut] |
| 10 | Flange Lock Nut | M8 | [Flanged Nut] |
| 2 | Nylon Lock Nut | M6 | [Nylon Lock Nut] |
| 2 | EVA | [EVA Pad/Material] |
Tools Required
- Drive Ratchet Handle
- 10mm, 13mm Wrench
- 4mm Hex Bit Socket
- 19mm Wrench
Installation Instructions
Step 1
Place the vehicle in park, remove the factory bumper from the frame.
Diagram description: Illustration showing a truck with the factory bumper removed, and mounting brackets highlighted on the frame.
Step 2
First, stick the EVA to the main body. Assemble your Hooke Road bumper. Align the outer profile with the inner profile and tighten the hardware. Repeat this step on the other side of the bumper.
Hardware: (2) EVA, (6) M12×30 Hex Bolt, (6) D12 Split Lock Washer, (6) M12×30×2 Flat Washer, (6) M12 Hex Nut.
Diagram description: Exploded view showing the main body of the bumper with EVA pads being attached. Hardware components (bolts, washers, nuts) are shown ready for assembly.
Step 3
Secure the bull bar to the bumper and tighten the hardware. Repeat this step for the opposite of the bumper.
Hardware: (8) M8×20 Hex Bolt, (8) D8 Split Lock Washer, (8) M8×16×1 Flat Washer, (8) M8 Flange Lock Nut.
Diagram description: Illustration showing the bull bar being attached to the main bumper body using bolts, washers, and nuts. The process is shown for both sides.
Step 4
Secure the winch power control box bracket to the bumper and tighten the hardware.
Hardware: (2) M8×20 Hex Bolt, (2) D8 Split Lock Washer, (2) M8×16×1 Flat Washer, (2) M8 Flange Lock Nut.
Diagram description: Close-up view of the bumper showing the winch power control box bracket being mounted using bolts, washers, and nuts.
Step 5
Secure the license plate bracket to the bumper and tighten the hardware.
Hardware: (2) M6×16 Button Bolt, (2) M6 Nylon Lock Nut, (2) M6×12×1 Flat Washer.
Diagram description: Illustration showing the license plate bracket being attached to the front of the bumper using bolts, washers, and nuts. The Hooke Road logo is visible on the bracket.
Step 6
Secure the bumper to the vehicle frame. Adjust the bumper to the desired position. Repeat this step on the other side of the vehicle. Finally, tighten all bolts.
Hardware: (4) M12×35 Hex Bolt, (4) D12 Split Lock Washer, (8) M12×30×2 Flat Washer, (4) M12 Hex Nut.
Diagram description: Diagram showing the assembled bumper being mounted to the vehicle's frame using large bolts, washers, and nuts. The process is shown for both sides of the vehicle.
Step 7
The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!
Diagram description: Front view of the truck with the new Hooke Road front bumper installed.
Find more parts by searching Google for "Hooke Road".
Feel free to share your vehicle on social media @HookeRoad4x4 using the hashtag #hookeroad.
