Hooke Road Front Bumper Installation Guide
Model: BXG.1012-S
Brand: HOOKE ROAD
MAKE A DIFFERENCE
? Contents:
This kit includes the following main components:
- Bull Bar
- Bumper
- D-rings
? Parts List:
| Qty | Part Name | Size(mm) | Picture Description |
|---|---|---|---|
| 6 | Hex Bolts | M12*30 | Image of a large bolt |
| 2 | Hex Bolts | M8*20 | Image of a smaller bolt |
| 6 | Split Lock Washer | D12 | Image of a split lock washer |
| 2 | Split Lock Washer | D8 | Image of a smaller split lock washer |
| 6 | Flat Washer | M12*30*2 | Image of a large flat washer |
| 2 | Flat Washer | M8*16*1.2 | Image of a smaller flat washer |
?️ Tools Required:
- 19mm Wrench
- 19mm Socket Wrench
Image shows a 19mm wrench and a 19mm socket wrench.
⏱️ Installation Time:
Estimated installation time is about 1 hour. 2-3 people may be needed. Installation time can vary based on mechanical skill level.
Important: PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!
To view the electronic version of the manual for BXG.1012-S, please scan the QR code (QR code excluded from output).
⚙️ Installation Instructions:
Step 1: Remove the original front bumper.
Image 1: Front view of a yellow Jeep Wrangler with its original bumper removed, revealing the mounting points.
Step 2: Assemble the bull bar & the bumper.
Attach the bull bar to the bumper using the Hex Bolts (M8*20), Split Lock Washer (D8), and Flat Washer (M8*16*1.2).
Image 2: Diagram illustrating the bull bar being bolted to the main bumper structure.
Step 3: Install the bumper on the Jeep.
Mount the assembled bumper onto the Jeep's frame as shown in the illustration.
Image 3: Close-up of the Jeep's frame showing the upper mounting holes for the bumper.
Image 4: Close-up of a hand inserting a bolt into an upper mounting point.
Step 4: Tighten the bumper using specified hardware.
Use a 19mm Socket Wrench or 19mm Wrench to secure the bumper with the Hex Bolts (M12*30), Split Lock Washer (D12), and Flat Washer (M12*30*2).
First, install the upper bolt holes.
Images 5 & 6: Close-up views showing the installation of components, possibly related to lighting or mounting brackets.
Second, install the bottom bolt hole.
Image 7: Close-up of the Jeep's frame showing the lower mounting holes.
Image 8: Close-up of a hand inserting a bolt into a lower mounting point.
Image 9: Close-up of a socket wrench being used to tighten a bolt.
Step 5: Install the other side.
Repeat the installation process for the opposite side of the vehicle using the same method.
Step 6: Install the D-rings.
Attach the D-rings to their designated mounting points on the bumper.
Image 10: Front view of the installed Hooke Road bumper on the Jeep, clearly showing the D-rings attached to the bumper.
Step 7: Installation completed.
The installation of the Hooke Road Front Bumper is now complete.
Main image: Front view of a yellow Jeep Wrangler with the Hooke Road front bumper fully installed.
Find more parts and information by searching "GoogleHooke Road" online.
Connect with Hooke Road on social media: Facebook, Instagram, TikTok @HookeRoad4x4
Share your Jeep/Truck build using the hashtag #hookeroad to win discounts every week.
