Kichler Lighting Fixture Installation Instructions

Installation Overview

This guide provides step-by-step instructions for installing your Kichler lighting fixture. Please read all instructions carefully before beginning.

NOTE: Fixture should be installed with the socket facing UP as shown in the diagram.

Parts List

• [A] Mounting Screw (2)
• [B] Canopy
• [C] Wall Anchor Screw (2)
• [D] Wall Anchor (2)
• [E] Strap Mounting Screw (2)
• [F] Mounting Strap
• [G] Outlet Box (not supplied)

Diagram Description: The fixture diagram illustrates the components and their assembly. It shows how the mounting strap [F] attaches to the outlet box [G] using screws [E]. It indicates marking points for additional wall mounting. The canopy [B] is shown attaching to the wall using mounting screws [A], potentially with wall anchors [D] and anchor screws [C].

Safety Precautions

Cleaning Instructions

• ? Always be certain that electric current is turned off before cleaning.
• ? Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

Installation Steps

Step 1: Attach Mounting Strap

Using the strap mounting screws [E], attach the mounting strap [F] to the outlet box [G]. Ensure the flat side of the mounting strap is against the wall, with the screw holes positioned at the 12 and 6 o'clock positions.

Step 2: Mark Additional Mounting Locations

Use the mounting strap as a template. Mark the positions for additional wall mounting locations through the holes near the top and bottom of the strap.

Step 3: Remove Strap

Carefully remove the strap mounting screws and the mounting strap from the outlet box.

Step 4: Prepare Wall Mounting Locations

If an additional wall mounting location is on a stud, use a 3/32" drill bit (not included) to drill a pilot hole. If the location is not on a stud, use a 3/16" drill bit (not included) to drill a hole for a wall anchor [D]. Insert the wall anchor into the hole and tap lightly until flush with the mounting surface.

Step 5: Reattach Mounting Strap

Using the strap mounting screws [E], reattach the mounting strap [F] to the outlet box [G]. Tighten to secure.

Step 6: Secure Strap to Wall

Secure the mounting strap to the wall by screwing the two (2) wall anchor screws [C] into the additional wall mounting locations. Tighten to secure.

Step 7: Grounding Instructions

For USA installations:

Diagram Description (a): For fixtures with a mounting strap featuring a hole and two raised dimples, wrap the ground wire from the outlet box around the green ground screw and thread it into the hole.

Diagram Description (b): For fixtures with a cupped washer, attach the ground wire from the outlet box under the cupped washer and the green ground screw, then thread into the mounting strap.

If the fixture has a ground wire, connect the fixture's ground wire to the outlet box's ground wire using a wire connector after completing the above steps. Never connect the ground wire to the black or white power supply wires.

Step 8: Make Wire Connections

Reference the chart below for correct wire connections.

Note: When using parallel wire (SPT 1 & SPT 2), the neutral wire is square-shaped or ridged, and the other wire will be round or smooth (see illustration). The neutral wire is typically white.

Step 9: Attach Canopy

Push the canopy [B] to the wall, carefully aligning the mounting screw holes in the top and bottom of the mounting strap with the corresponding holes in the canopy. NOTE: Ensure all wires are inside the canopy and are not pinched between the mounting strap and canopy, or between the wall and the canopy.

Step 10: Secure Fixture

Screw two (2) mounting screws [A] into the holes in the canopy and mounting strap to attach the fixture to the wall. One screw at the top and one at the bottom. Tighten to secure.

Step 11: Install Bulbs

Insert recommended bulb(s) (not included).