Assembly Instructions

Warning: Excessive weight hazard! Use two or more people to move, assemble, or install cabinets to avoid back injury. Do not leave children unattended near cabinets. There is a high risk of tipping if cabinets are installed incorrectly. Securely attach cabinets to the wall to avoid serious injury.

Diagram description: Shows incorrect lifting with one person (❌) and correct lifting with two people (✔️).

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

Check you have all the components and tools listed on the following pages.
Remove all fittings from the plastic bags and separate them into their groups.
Keep children and animals away from the work area; small parts could cause choking if swallowed.
Make sure you have enough space to lay out the parts before starting.
During assembly, do not stand or put weight on the product, as this could cause damage.
Assemble the item as close to its final position (in the same room) as possible.
Assemble on a soft, level surface to avoid damaging the unit or your floor.
Parts of the assembly will be easier with 2 people.
To reduce the likelihood of damaging your product, please ensure that your power drill is set on a low torque setting. ⚙️

Care and maintenance

Only clean using a damp cloth and mild detergent; do not use bleach or abrasive cleaners.
From time to time, check that there are no loose screws on this unit.
This product should not be discarded with household waste. Take it to your local authority waste disposal centre.

Handy Hints

Assemble all parts and bolts loosely during assembly; only once the product is complete should you fully tighten the bolts.
Regularly check and ensure that all bolts and fittings are tightened properly.

WARNING: In order to help prevent overturning, please follow these instructions

To help prevent product toppling over, please follow the below steps:

Use the anti-tip strap or wall-fixing method provided (if applicable).
Do not allow children to climb or hang on the furniture.
Do not open more than one drawer at a time.
Do not place heavy items in the top drawers.
Do not place heavy items on top of the furniture, unless the furniture has been designed for this purpose.

Please note that only the anti-tip strap is provided. You will need to provide wall plugs and screws applicable for your wall type.

Product Parts

Part Code	Description	Quantity
LSP	LEFT SIDE PANEL	1PC(S)
RSP	RIGHT SIDE PANEL	1PC(S)
DE	DECK	1PC(S)
DF	DRAWER FACE	1PC(S)
FCP	CONNECTING PANEL	3PC(S)
DO	DOOR	2PC(S)
BP	BACK PANEL	1PC(S)
SPL	SHELF PANEL	1PC(S)
LD	LEFT DRAWER SIDE	1PC(S)
RD	RIGHT DRAWER SIDE	1PC(S)
BD	DRAWER BACK	1PC(S)
DD	DRAWER BOTTOM	1PC(S)
DCP	CONNECTING PANEL	2PC(S)

Hardware and Tools

Hardware

a) Cam Bolt x 22
b) Cam Lock x 14
c) Hinge x 4
d) Screw Φ4*16 x 40
e) Shelf Support x 4
f) Dowel x 26
g) Cam Bolt x 4
h) Drawer Slide x 2
sb) Cam Lock x 8

Recommended Tools

SCREWDRIVER
DRILL
RUBBER MALLET

Assembly Steps

Step 1: Attach 10x Cam Bolts (a) to the inner surfaces of the Left Side Panel (LSP) and Right Side Panel (RSP). Diagram shows correct insertion of cam bolts into pre-drilled holes.
Step 2: Attach 3x Dowels (f) and 3x Screws (d) to the Left Side Panel (LSP). Attach 1x Drawer Slide (h) to the inner side of LSP. Diagram shows screw and dowel insertion, and slide attachment.
Step 3: Attach 3x Dowels (f) and 3x Screws (d) to the Right Side Panel (RSP). Attach 1x Drawer Slide (h) to the inner side of RSP. Diagram shows screw and dowel insertion, and slide attachment.
Step 4: Attach 4x Cam Bolts (a) to the Deck (DE) panel. Diagram shows cam bolt insertion.
Step 5: Insert 20x Dowels (f) into the edges of 3x Connecting Panels (FCP) and 2x Connecting Panels (DCP). Diagram shows dowel insertion into panels.
Step 6: Insert the assembled Connecting Panels (FCP x3, DCP x1) into the base panel (LSP). Diagram shows panels being slotted into the base.
Step 7: Insert 5x Cam Locks (b) into the corresponding holes on the LSP, FCP, and DCP panels. Diagram shows cam lock insertion and rotation.
Step 8: Slide the Back Panel (BP) into the grooves on the rear of the assembled structure. Diagram shows the back panel being inserted.
Step 9: Prepare the drawer slides (h) for the Left Side Panel (LSP). The diagram shows the 'OPEN' label on the slide and indicates two types of slides, labeled 'ha' and 'hb'.
Step 10: Prepare the drawer slides (h) for the Right Side Panel (RSP). The diagram shows the 'OPEN' label on the slide and indicates two types of slides, labeled 'ha' and 'hb'.
Step 11: Place the Right Side Panel (RSP) top panel onto the assembled structure. Diagram shows the top panel being lowered into place.
Step 12: Insert 5x Cam Locks (b) into the RSP top panel and side panels to secure them. Diagram shows cam lock insertion and rotation.
Step 13: Slide the Drawer Face (DF) into position. Diagram shows the drawer face being inserted from the side.
Step 14: Insert 4x Cam Locks (b) into the Drawer Face (DF) and side panels to secure it. Diagram shows cam lock insertion and rotation.
Step 15: Attach 4x Cam Bolts (g) and 12x Screws (d) to the cabinet structure. Insert Cam Locks (b) to secure these components. The diagram illustrates three stages of cam lock engagement.
Step 16: Attach the adjustable feet to the bottom of the cabinet. Diagram shows correct (✔️) and incorrect (❌) foot attachment methods.
Step 17: Insert 4x Shelf Supports (e) into the pre-drilled holes on the side panels (LSP, RSP). Place the Shelf Panel (DE) onto the supports. Diagram shows supports being inserted and the shelf panel placed.
Step 18: Insert the Shelf Panel (SPL) into the cabinet. Diagram shows the shelf panel being slid into place.
Step 19: Attach 8x Cam Bolts (a) to the Left Drawer Side (LD) and Right Drawer Side (RD) panels. Diagram shows cam bolt insertion.
Step 20: Attach 2x Cam Locks (sb) to the Drawer Face (DF) and drawer sides. A warning symbol ⚠️ is shown with a measurement of "1 1/2 "". Diagram shows cam lock insertion and rotation.
Step 21: Insert the Drawer Bottom (DD) into the grooves of the Drawer Face (DF) and Drawer Back (BD). Diagram shows the drawer bottom being slid into place.
Step 22: Attach 2x Cam Locks (sb) to the Drawer Back (BD) and drawer sides. Diagram shows cam lock insertion and rotation, with a "100%" indicator for full lock.
Step 23: Attach the Drawer Top Rail (LD) to the drawer front (DF) and drawer sides. Diagram shows the top rail being attached.
Step 24: Attach 4x Cam Locks (sb) to the drawer front (DF) and drawer sides. Diagram shows cam lock insertion and rotation, with a "100%" indicator for full lock.
Step 25: Attach 2x Drawer Slides (ha) to the assembled drawer using 6x Screws (d). Diagram shows slide attachment to the drawer.
Step 26: Insert the assembled drawer into the cabinet. Diagram shows the drawer being slid into the cabinet runners.
Step 27: Attach 4x Hinges (c) and 8x Screws (d) to the Doors (DO). Diagram shows hinge attachment to the door.
Step 28: Attach the hinges (c) to the cabinet body (LSP, RSP) using 4x Screws (d). Diagram shows hinge attachment to the cabinet.
Step 29: Attach the Doors (DO) to the cabinet body using the hinges. Use 4x Screws (d). Diagram shows door attachment.
Step 30: Adjust the hinges for proper door alignment. Diagrams illustrate adjustment screws for vertical, horizontal, and depth positioning.
Step 31: Final assembled product view.

Models: nnit1173, W115401070, Latitude Run NNIT1173 Premium Garage Modular Storage Base Cabinet, Latitude Run NNIT1173, Premium Garage Modular Storage Base Cabinet, Garage Modular Storage Base Cabinet, Modular Storage Base Cabinet, Storage Base Cabinet, Base Cabinet, Cabinet

Google Docs
Google Drive
Download [pdf]
Download Optimized

File Info : application/pdf, 21 Pages, 4.20MB

nnit1173 owner manual Adobe PDF library 15.00 Adobe Illustrator 25.2 (Windows)

Related Documents

	Latitude Run NNIT1174 Base Cabinet Assembly Instructions Step-by-step assembly instructions for the Latitude Run NNIT1174 base cabinet, featuring safety guidelines, parts identification, hardware details, and clear assembly procedures for building your storage unit.
	Latitude Run Modular Storage Drawer Base Cabinet Assembly Instructions Detailed assembly instructions for the Latitude Run modular storage drawer base cabinet, including parts list, hardware, tools, safety warnings, and step-by-step guidance for model nnit1180.
	Latitude Run nnit1186 Tall Cabinet Assembly Instructions Step-by-step assembly guide for the Latitude Run nnit1186 Tall Cabinet, including safety warnings, parts list, hardware details, and assembly instructions.
	How to Assemble a 20-45cm Drawer Storage Cabinet - Step-by-Step Installation Guide Detailed instructions and visual guides for assembling a 20-45cm drawer storage cabinet. Learn each step, identify parts, and understand quantities for different layer configurations. Easy assembly process, no tools required.
	Assembly Instructions for Latitude Run NNIT1164 Tall Storage Cabinet Comprehensive assembly instructions for the Latitude Run NNIT1164 tall storage cabinet. This guide includes safety warnings, a detailed parts list, hardware identification, recommended tools, and step-by-step assembly procedures for building your furniture.
	Installation Manual for Latitude Run 4-Door Accent Cabinet with 2 Drawers A comprehensive installation guide for the Latitude Run accent cabinet, featuring detailed step-by-step assembly instructions, parts inventory, hardware list, and important safety information. Includes warranty and returns policy.
	Installation Manual for Latitude Run JMBB2561 Storage Cabinet Step-by-step installation guide for the Latitude Run JMBB2561 Kitchen Pantry Storage Cabinet with Glass Doors. Includes parts list, assembly instructions, safety warnings, and warranty information.
	Storage Cabinet User Manual - Assembly Guide Detailed assembly instructions and user guide for the Latitude Run Storage Cabinet (model tsya1157), including hardware and parts lists, and step-by-step assembly procedures.