INSTALLATION Product Manual

Introduction & Important Information

❓ IMPORTANT INFORMATION! Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.

? AVOID SCRATCHES! In order to avoid scratching this furniture, it should be assembled on a soft layer, such as a rug.

? IMPROVE EFFICIENCY ! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

⚠️ ANTI-TOPPLE WARNING ! Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment. If not included with this product, please purchase a wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.

❗ IMPORTANT! It is important that any product which is assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product. For regular maintenance and cleaning of the product, for the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.

Tools Required

• Measuring tape ?
• Pencil ✏️
• Level ?
• Hammer ?
• Screwdriver ?
• Power drill ?

Hardware List

When installing, please carefully confirm whether each screw corresponds to the manual; accessories with similar shapes can be distinguished by size.

Parts List

• Part 1: Top Panel (1PC)
• Part 2: Side Panel (2PCS)
• Part 3: Side Panel (2PCS)
• Part 4: Bottom Panel (1PC)
• Part 5: Base Panel (1PC)
• Part 6: Middle Divider (1PC)
• Part 7: Back Panel (1PC)
• Part 8: Support Rail (2PCS)
• Part 9: Back Board (4PCS)
• Part 10: Leg (4PCS)
• Part 11: Leg Support (1PC)
• Part 12: Shelf (2PCS)
• Part 13: Shelf (2PCS)
• Part 14: Drawer Front Panel (2PCS)
• Part 15: Drawer Side Panel (2PCS)
• Part 16: Drawer Side Panel (2PCS)
• Part 17: Drawer Back Panel (1PC)
• Part 18: Drawer Bottom Panel (1PC)
• Part 19: Door (2PCS)
• Part 20: Door (2PCS)

Assembly Instructions

Step 1: Attach Rails

Attach rail (G) and rail (H) to board 5 and board 7 respectively, using screw (F). Then, attach rail (H) to board 6 using screw (F). Flip board 6 to its back and attach rail (G) as shown.

Step 2: Install Eccentric Rods

Screw eccentric rod (A) into board 5 and board 7 at first.

Step 3: Attach Part P to Board 2

Fix part (P) to board 2 using screw (S) as shown. This step is to be performed twice for two instances of board 2.

Step 4: Attach Board 8 to Board 6

Screw eccentric rod (B) into board 6. Attach board 8 to board 6, add cam lock (C) into board 8, and turn clockwise to tighten as shown.

Step 5: Attach Board 8 to Board 6 (Continued)

Attach board 8 to board 6, add cam lock (C) into board 8, and turn clockwise to tighten as shown.

Step 6: Attach Boards 2 & 3 to Board 6

Screw eccentric rod (B) and insert wooden dowel (E) into board 6. Attach board 2 and board 3 to board 6, add cam lock (C) into boards 2 and 3, and turn clockwise to tighten as shown.

Step 7: Attach Boards 2 & 3 to Board 6 (Continued)

Attach board 2 and board 3 to board 6, add cam lock (C) into boards 2 and 3, and turn clockwise to tighten as shown.

Step 8: Attach Board 5 to Assembly

Attach board 5 to board 2, board 8, and board 3 using wooden dowel (D). Add cam lock (C) into boards 2, 8, and 3, and turn clockwise to tighten as shown.

Step 9: Attach Board 7 to Assembly

Attach board 7 to board 2, board 3, and board 8 using wooden dowel (D). Add cam lock (C) into boards 2, 8, and 3, and turn clockwise to tighten as shown.

Step 10: Insert Back Boards

Insert back board (9) along the available grooves as shown.

Step 11: Attach Legs to Board 4

Fix leg part (10) and leg support (11) to board 4 using screw (K) and Allen key (L) as shown.

Step 12: Attach Board 4 to Main Structure

Attach board 4 to board 5, board 6, and board 7 using wooden dowel (D) and fix with screw (O) as shown.

Step 13: Insert Back Boards (Continued)

Insert back board (9) along the available grooves as shown.

Step 14: Attach Part P to Board 1

Fix part (P) to board 1 using screw (S) as shown. This step is to be performed twice for two instances of board 1.

Step 15: Install Eccentric Rods on Board 1

Screw eccentric rod (A) into board 1 as shown.

Step 16: Attach Board 1 to Top

Attach board 1 to the top of the structure using wooden dowel (D). Add cam lock (C) into the corresponding holes and turn clockwise to tighten as shown.

Step 17: Insert Back Buckles

Insert buckle (N) into the back slots and fix with screw (F) as shown.

Step 18: Assemble Drawer Sides and Base

Fix board 12, board 16, and board 13 to board 14 using screw (M) as shown. Insert board 15 along the grooves as shown. This step is to be performed twice for two drawer assemblies.

Step 19: Prepare Drawer Fronts

Screw eccentric rod (A) into board 17 and board 18 as shown. Stick part (P) to board 17 and board 18.

Step 20: Attach Drawer Sides to Drawer Fronts

Attach board 17 and board 18 to board 12, board 16, and board 13 using cam lock (C). Turn clockwise to tighten as shown.

Step 21: Attach Drawer Tracks

Fix track (I) and track (J) to board 12 and board 13 using screw (F) as shown.

Step 22: Door Hinge Information

Pay attention to the difference between the middle parts of the two types of door hinges. The large curved door hinges (Q) are used on the outermost door plates, and the small curved door hinges (R) are used on the door panel in the middle of the cabinet.

Step 23: Attach Hinges to Doors

Fix hinge (Q) to board 19 and board 20 using screw (S) as shown.

Step 24: Attach Doors (Hinge Q)

Assemble door 19 and door 20 (using hinge Q) to board 5 and board 7 using screw (S) as shown.

Step 25: Attach Hinges to Doors (Hinge R)

Fix hinge (R) to board 19 and board 20 using screw (S) as shown.

Step 26: Attach Doors (Hinge R)

Assemble another door 19 and door 20 (using hinge R) to board 6 using screw (S) as shown.

Step 27: Insert Drawers

Insert the assembled drawers (17, 18) into the cabinet as indicated by the arrows.

Step 28: Install Anti-Tipping Device

Install the anti-tipping device as shown. Attach brackets (U) to the wall and the furniture using screws (W, X) and wall plugs (V) if necessary. Secure with the strap (T).

Warranty

WARRANTY CLAIMS

• There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
• Before making a claim, please call us. Please leave your purchase order number, along with some details of the problem, if you want a replacement part. We will arrange within 48 hours. If there is out of stock, we will reply with a shipping date.
• The product must be used in accordance with the instructions provided. For health reasons.
• For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.

Type of Warranty Claim

• Failure to follow the furniture instructions will invalidate the warranty.
• Does not include damage during installation, but includes damage during transportation.

Scope of Responsibility

• Shall not bear any responsibility for misuse or user damage and / or loss of parts during the installation of furniture.
• After use, damage and scratches of the furniture are not covered by the warranty.

The Warranty Relates to All Bought in The US and Covers The Following Areas

• Sheet parts: 1 month from the date of purchase.
• Electrical parts: 1 month from the date of purchase.

RETURNS

CHANGED YOUR MIND AND NEED TO RETURN YOU ITEM?

PLEASE FOLLOW THE BELOW INSTRUCTIONS:

• If you have purchased and have simply changed your mind, follow the retailer's instructions for returns.

DEFECTIVE ITEMS

• If your item is defective in any way, i.e. it doesn't work but you can't identify why, in the first instance, please call us.

DAMAGED ITEMS

• If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is refused. If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.
• In all circumstances, please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardise your chances of making a claim, and you may not receive a credit for the return.