ASSEMBLY INSTRUCTION
Warning: Excessive weight hazard!
Use two or more people to move, assemble, or install cabinets to avoid back injury. Do not leave children unattended near cabinets. There is a high risk of tipping if cabinets are installed incorrectly. Securely attach cabinets to the wall to avoid serious injury.
Diagram Description: A large exclamation mark within a triangle (⚠️) is shown to the left. The main diagram depicts two figures lifting a tall cabinet. Below this, two smaller diagrams illustrate safety: one with a cross (❌) showing a single person struggling to lift, and another with a checkmark (✔️) showing two people lifting safely.
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
- Check you have all the components and tools listed on the following pages.
- Remove all fittings from the plastic bags and separate them into their groups.
- Keep children and animals away from the work area; small parts could be a choking hazard if swallowed.
- Make sure you have enough space to lay out the parts before starting.
- During assembly, do not stand or put weight on the product, as this could cause damage.
- Assemble the item as close to its final position (in the same room) as possible.
- Assemble on a soft, level surface to avoid damaging the unit or your floor.
- Parts of the assembly will be easier with 2 people.
- To reduce the likelihood of damaging your product, please ensure that your power drill is set on a low torque setting.
Care and maintenance
- Only clean using a damp cloth and mild detergent; do not use bleach or abrasive cleaners.
- From time to time, check that there are no loose screws on this unit.
- This product should not be discarded with household waste. Take it to your local authority waste disposal centre.
Handy Hints
- Assemble all parts and bolts loosely during assembly; only once the product is complete should you fully tighten the bolts.
- Regularly check and ensure that all bolts and fittings are tightened properly.
WARNING
In order to help prevent overturning, please follow these instructions:
To help prevent product toppling over, please follow the below steps:
- Use the anti-tip strap or wall fixing method provided (if applicable).
- Do not allow children to climb or hang on the furniture.
- Do not open more than one drawer at a time.
- Do not place heavy items in the top drawers.
- Do not place heavy items on top of the furniture, unless the furniture has been designed for this purpose.
Please note that only the anti-tip strap is provided. You will need to provide wall plugs and screws applicable for your wall type.
Product Parts
Diagram Description: An exploded view of the cabinet components is shown, with each part labeled with a letter code. The main parts are: LSP (Left Side Panel), RSP (Right Side Panel), DE (Deck), DCP (Connecting Panel), DO (Door), BP (Back Panel), SPL (Shelf Panel), MPL (Fixed Shelf Panel), TE (Top Panel).
| Label | Part Name | Quantity |
|---|---|---|
| LSP | Left Side Panel | 1PC(S) |
| RSP | Right Side Panel | 1PC(S) |
| DE | Deck | 1PC(S) |
| DCP | Connecting Panel | 5PC(S) |
| DO | Door | 2PC(S) |
| BP | Back Panel | 1PC(S) |
| SPL | Shelf Panel | 3PC(S) |
| MPL | Fixed Shelf Panel | 1PC(S) |
| TE | Top Panel | 1PC(S) |
Hardware
- a) Cam Bolt x 22
- b) Cam Lock x 22
- c) Hinge x 8
- d) Screw Φ4*16 x 44
- e) Shelf Pin x 12
- f) Dowel x 36
- g) Foot/Leveler x 4
Recommended Tools
- Screwdriver
- Drill
- Rubber Mallet
Assembly Steps
Step 1
Insert 18 Cam Bolts (a) into the designated holes on the inner faces of the Left Side Panel (LSP) and Right Side Panel (RSP). Insert 36 Dowels (f) into the corresponding holes on the LSP and RSP. Ensure correct alignment as shown in the diagram. Diagram Description: Shows LSP and RSP laid flat with multiple holes. Cam bolts (a) are screwed in, and dowels (f) are inserted. Insets show correct insertion and alignment warnings (✔️/❌).
Step 2
Insert 6 Dowels (f) into the designated holes on the Top Panel (TE). Align the Top Panel (TE) with the top edge of the assembled LSP and RSP structure, ensuring the dowels fit into the corresponding holes. Diagram Description: Shows TE with dowels (f) inserted, then being lowered onto the LSP/RSP assembly.
Step 3
Insert 4 Dowels (f) into the designated holes on the Fixed Shelf Panel (MPL). Align the MPL with the middle section of the assembled LSP and RSP structure, ensuring the dowels fit into the corresponding holes. Diagram Description: Shows MPL with dowels (f) inserted, then being positioned within the LSP/RSP assembly.
Step 4
Insert 4 Cam Bolts (a) into the designated holes on the Deck (DE). Align the Deck (DE) with the bottom of the assembled LSP and RSP structure. Diagram Description: Shows DE with cam bolts (a) inserted, then being positioned at the base of the LSP/RSP assembly.
Step 5
Insert 20 Dowels (f) into the designated holes on the 5 Connecting Panels (DCP). Insert these 5 DCPs vertically into the slots or holes within the main cabinet structure, between the side panels and the deck/shelf. Diagram Description: Shows DCPs with dowels (f) inserted, then being placed vertically into the cabinet frame.
Step 6
Lower the Top Panel (TE) onto the partially assembled cabinet structure, aligning it with the top edges of the side panels (LSP) and vertical connecting panels (DCP). Diagram Description: Arrow indicates TE being placed on top of the structure.
Step 7
Secure the Top Panel (TE) to the Left Side Panel (LSP) using 2 Cam Locks (b). Insert the Cam Locks (b) into the TE and turn them clockwise (indicated by a circular arrow with '100%') until fully tightened. Diagram Description: Shows TE attached to LSP, with cam locks (b) being tightened. Inset shows cam lock mechanism.
Step 8
Insert the Fixed Shelf Panel (MPL) vertically between the TE and LSP, aligning with pre-drilled holes. Diagram Description: Arrow indicates MPL being inserted vertically into the structure.
Step 9
Secure the Fixed Shelf Panel (MPL) to the side panels (LSP and implied RSP) using 2 Cam Locks (b). Insert the Cam Locks (b) into the MPL and turn them clockwise (indicated by '100%') until fully tightened. Diagram Description: Shows MPL secured with cam locks (b).
Step 10
Insert the remaining Connecting Panels (DCP) vertically into the structure, between the side panels and the fixed shelf/deck. Diagram Description: Multiple DCPs are shown being inserted vertically.
Step 11
Secure the Connecting Panels (DCP) to the side panels and other horizontal elements using 5 Cam Locks (b). Insert the Cam Locks (b) and turn them clockwise (indicated by '100%') until fully tightened. Diagram Description: Shows DCPs secured with cam locks (b).
Step 12
Slide the Back Panel (BP) into the grooves or attach it to the rear of the cabinet. Diagram Description: Arrows indicate BP being slid into place at the back of the cabinet.
Step 13
Attach the Right Side Panel (RSP) to the right side of the cabinet, aligning it with the top, deck, and connecting panels. Arrows indicate downward movement. Diagram Description: RSP is shown being attached to the right side of the cabinet.
Step 14
Secure the Right Side Panel (RSP) using 4 Cam Locks (b). Insert the Cam Locks (b) and turn them clockwise (indicated by '100%') until fully tightened. Diagram Description: Shows RSP secured with cam locks (b).
Step 15
Secure the Connecting Panels (DCP) to the side panels and other horizontal elements using 5 Cam Locks (b). Insert the Cam Locks (b) and turn them clockwise (indicated by '100%') until fully tightened. Diagram Description: Shows DCPs secured with cam locks (b).
Step 16
Slide the Deck (DE) into place at the bottom of the cabinet, likely into grooves or against the connecting panels. Diagram Description: Arrow indicates DE being slid into place at the bottom.
Step 17
Secure the Deck (DE) using 4 Cam Locks (b). Insert the Cam Locks (b) and turn them clockwise (indicated by '100%') until fully tightened. Diagram Description: Shows DE secured with cam locks (b).
Step 18
Attach 4 Feet/Levelers (g) to the underside of the Deck (DE) using 12 Screws (d) of size Φ4*16. Diagram Description: Shows the bottom of the cabinet with feet (g) being attached using screws (d). Insets show close-ups and a multi-step attachment process (I, II, III).
Step 19
Attach 8 Hinges (c) to the inside of the 2 Doors (DO) using 16 Screws (d) of size Φ4*16. Diagram Description: Shows the inside of the Doors (DO) with hinges (c) being attached using screws (d). Insets show close-ups of hinge attachment.
Step 20
Attach the Doors (DO) to the front of the cabinet frame using the pre-attached hinges (c). Use Screws (d) to secure the hinges to the cabinet frame. Diagram Description: Shows Doors (DO) being attached to the cabinet frame with hinges (c) and screws (d). Inset shows hinge attachment detail.
Step 21
Further secure the Doors (DO) to the cabinet frame using Screws (d). This step may involve final adjustments or additional securing points for the doors. Diagram Description: Shows additional screws (d) being used to attach hinges (c) to the cabinet frame for the doors.
Step 22
Warning: Ensure correct orientation for stability. The diagram shows the assembled cabinet body and a separate tall side panel. An arrow indicates the tall panel is to be attached to the main body. A warning symbol (⚠️) is shown with two diagrams: one showing correct attachment with a checkmark (✔️), and one showing incorrect attachment with a cross (❌), likely related to stability or tipping when attaching the final side panel. Diagram Description: Shows the main cabinet body and a side panel being brought together, with a safety warning about correct attachment.
Step 23
Adjust the hinges on the cabinet doors for proper alignment. The diagram shows close-ups of hinge adjustment screws with arrows indicating how to move the doors up/down, left/right, and in/out. Diagram Description: Shows hinge adjustment mechanisms with arrows indicating movement directions.
Step 24
Insert 12 Shelf Pins (e) into the pre-drilled holes on the inner sides of the cabinet at the desired shelf heights. Diagram Description: Shows Shelf Pins (e) being inserted into holes inside the cabinet. An inset shows a close-up of a shelf pin insertion.
Step 25
Place the 3 Shelf Panels (SPL) onto the installed Shelf Pins (e) inside the cabinet. Arrows indicate downward placement. Diagram Description: Shows Shelf Panels (SPL) being placed onto the shelf pins within the cabinet.
Step 26
The diagram shows the completed tall cabinet with two doors closed and standing upright. Diagram Description: A final view of the fully assembled cabinet.
