VEVOR MONITOR DESK MOUNT

Product Overview

This user manual provides instructions for the VEVOR S100 Monitor Desk Mount. It is designed to securely hold monitors and offer adjustable positioning for improved ergonomics.

Key Specifications:

• Max Load Capacity: 20 lbs
• Supported Screen Size: 13-32 inches
• VESA Compatibility: 75x75mm, 100x100mm

The mount features a gas spring arm for smooth height and angle adjustments.

Safety Instructions

WARNING

Read this material before using this product. Failure to do so can result in serious injury.

Assembly Precautions

• Assemble only according to these instructions. Improper assembly can create hazards.
• Keep the assembly area clean and well-lit.
• Keep bystanders out of the area during assembly.
• Do not assemble when tired or when under the influence of alcohol, drugs, or medication.
• The product capabilities apply to properly and completely assembled products only.
• For additional information regarding the parts listed, please refer to the Assembly Diagram. Unwrap and separate all parts in a clean work area.

Use Precautions

• Use with products heavier than the rated weights indicated may result in instability causing possible injury.
• Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

SAVE THIS MANUAL

Product Parameters

Parts List

The following components are included with the VEVOR S100 Monitor Desk Mount:

• A: M4×10 Screws (x4)
• B: M5×10 Screws (x4)
• C: M8×20 Screw (x1)
• D: Washers (x4)
• E: 4mm Allen Key (x1)
• F: 5mm Allen Key (x1)
• 1: Clamp Base (x1)
• 2: Grommet Base (x1)
• 3: Pole (x1)
• 4: Lower Clamp Plate (x1)
• 5: Upper Clamp Plate (x1)
• 6: Monitor Arm (x1)
• 7: Monitor Plate (x1)

Refer to diagrams for visual identification of parts.

Assembly Steps

Method 1: Clamp Mounting

This method attaches the mount to the edge of a desk or table.

Step 1a-1: Prepare the Base

Attach the clamp base (1) to the lower clamp plate (4) using screw (C). Secure with the 5mm Allen Key (F).

Step 1a-2: Attach Pole

Connect the pole (3) to the clamp base assembly using screws (A) and washers (D). Ensure the pole is positioned correctly, typically allowing for a desk thickness of 10-62mm.

Step 1a-3: Secure to Desk

Position the clamp base assembly onto the desk edge. Insert the pole through the clamp mechanism and secure it tightly using the 5mm Allen Key (F).

Method 2: Grommet Mounting

This method is used when the desk has a pre-drilled hole for mounting.

Step 1b-1: Insert Grommet Base

If your desktop has a hole for item 2, insert the grommet base (2) through the hole. Attach the clamp base (1) and pole (3) to the grommet base using screws (F).

Step 2: Assemble Arm to Base

Attach the monitor arm assembly (6) to the top of the pole (3). Use the provided Allen keys (E, C) and screws to secure the arm firmly to the pole.

Step 3: Connect Monitor to Arm

Start by screwing the monitor plate (7) to the correct angle for easy placement of the monitor. Use a spanner (F) to screw the screws (A/B) and washers (D) into the two holes on the upper back of the display. Then, screw the VESA plate (7) into the two holes on the lower end of the monitor. Avoid excessive tightening screws to prevent monitor damage.

Step 4: Adjust Gas Spring Tension

This step ensures the monitor arm stays in the desired position without falling or popping up.

Case 1: Monitor/Arm Falls Down

Press the arm to make it keep in a horizontal position. Use the 5mm Allen Key (F) to adjust the screw on the arm. Turn counter-clockwise (indicated by '+') to increase gas spring tension until it can hold the weight of your monitor. Note: You may need to turn the screw by many circles to tighten the arm.

Case 2: Monitor/Arm Pops Up

Press the arm to make it keep in a horizontal position. Use the 5mm Allen Key (F) to adjust the screw on the arm. Turn clockwise (indicated by '-') to reduce gas spring tension until it can stay in the needed position. Note: You may need to turn the screw by many circles to tighten the arm.

Step 5: Adjust Flexibility (Pitching Angle)

If you feel the pitching angle is too tight or too loose when adjusting the mount, please adjust the screw using the Allen Key (F).

• (+) Turn clockwise to tighten
• (-) Turn counterclockwise to loose

Step 6: Cable Management

Route cables neatly along the monitor arm to keep the workspace tidy.

Step 7: Adjustable Instruction

The monitor arm offers various adjustment ranges:

• Base Rotation: 360° ?
• Arm Joint Rotation: 360° ?
• Monitor Plate Tilt: +60° / -60° ?
• Monitor Plate Swivel: 180° ?

Diagrams show rotational capabilities for the base, arm joints, and monitor plate tilt/swivel.

Contact and Support

Need Help? Contact Us!

For product questions or technical support, please feel free to contact:

✉ CustomerService@vevor.com

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret its user manual. The appearance of the product shall be subject to the product you received. VEVOR will not inform users again if there are any technology or software updates on our product.

Company Information

Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai

Imported to AUS: SIHAO PTY LTD, 1 ROKEVA STREET EASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EC REP: SHUNSHUN GmbH, Römeräcker 9 Z2021,76351 Linkenheim-Hochstetten, Germany

UK REP: Pooledas Group Ltd, Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom

Made In China