VEVOR

TV STAND WITH MOUNT

USER MANUAL

MODEL NO.: C240415S-01

VEVOR is committed to providing tools at competitive prices. Phrases like "Save Half" or "Half Price" represent estimated savings compared to major top brands and do not necessarily apply to all product categories. Customers are advised to verify savings when placing an order.

NEED HELP? CONTACT US!

For product questions or technical support, please contact:

Technical Support and E-Warranty Certificate
www.vevor.com/support

This is the original instruction manual. Please read all instructions carefully before operating. VEVOR reserves the right to interpret this user manual. The appearance of the product is subject to the item received. VEVOR may update technology or software without prior notice.

WARNING: Please read this manual carefully before using the product. Failure to do so may result in serious injury.

TECHNICAL SPECIFICATIONS

*Products such as specifications, appearance, and design are subject to modification without prior notice.

PACKAGE CONTENTS

Installation of Cams and Pins

Screw the pin into the hole. To set the cams correctly, ensure that the arrow on the cam is pointing to the hole of the pin and lock it. Lock the cam by turning the cam head with a screwdriver until it is tightened. Please do not use an electric screwdriver to assemble the unit.

Read each step carefully before starting. It is very important that each step of instruction is performed in the correct order. If these steps are not followed in sequence, assembly difficulties will occur.

Parts & Hardware List

ASSEMBLY STEPS

Step 1

Attach side frames (4) to vertical supports (7, 8) using screws (Y) and cam locks (P).

Step 2

Attach shelves (1, 2) and support bars (5, 6) to the assembled side frames using screws (Y, T, O) and cam locks (P).

Step 3

Attach support bars (13) to shelves (1, 2) using screws (B) and cam dowels (N).

Step 4

Assemble the top panels (9, 10, 11, 12) using screws (W).

Step 5

Attach the assembled top panels to the main structure using screws (B, F).

Step 6

Instructions for using light strips (if applicable). Use cable ties (R) to secure wires.

Step 7

Attach vertical supports (7, 8) to the assembled structure using screws (H).

Step 8

Attach the main structure to the side frames using screws (H).

Step 9

Attach the top panels (9, 10) to the vertical support assembly using screws (F).

Step 10

Secure the TV mount bracket (14) to the vertical support using screws (I).

Step 11

Attach the TV mount arms (15) to the TV mount bracket (14) using screws (M, L, O, V).

Step 12

Mount the TV to the TV mount arms using appropriate TV screws (TV1-TV8), washers (TV6), and spacers (TV7-TV8) as needed. Ensure the brackets are centered and level.

Step 13

The bracket can rotate 40 degrees to both the left and right sides. [arrow-left emoji] [arrow-right emoji]

Step 14

The light strip is installed under the countertop. Tie the wire with black strips (R). [light-strip emoji]

Step 15

TV Mounting: Ensure the correct bolt diameter fits your TV. Use the appropriate washer (TV6) and spacer (TV7-8) if necessary. Ensure monitor brackets are vertically centered and level with each other. [check-mark emoji]

COMPLETION

The TV stand with mount is now assembled and ready for use.

FCC Information

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment!

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This product may cause harmful interference.
2. This product must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this product not expressly approved by the party responsible for compliance could void the user's authority to operate the product.

Note: This product has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This product generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the distance between the product and receiver.
• Connect the product to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for assistance.