ROYALCRAFT ZWD001 Cabinet
Transforming houses into homes
Instruction Manual
Contact Information
Question about your product? We're here to help. Contact us by:
- Phone: 707-392-8405 [?]
- Email: support@royalcraft.store [✉️]
- Website: www.royalcraft.store [?]
If you have any problems, please send your order number and photos to us. We will contact you within 24 hours and provide you with a satisfactory solution.
NOTICE: Please retain these instructions for future reference.
General Assembly Advice:
- Carefully unpack all components and verify that all necessary parts are included.
- Identify each component and refer to the assembly diagrams or step-by-step instructions.
- Assemble the furniture in the specified order for proper alignment and fit.
- Use the provided tools or recommended tools for assembly. Do not use excessive force when tightening screws or bolts.
- If difficulties arise, consult the troubleshooting section or contact customer support.
Parts List
| Label | Description | Quantity |
|---|---|---|
| A | Left Side Panel | 1 PC |
| B | Right Side Panel | 1 PC |
| C | Bottom Panel | 1 PC |
| D | Center Divider Panel | 1 PC |
| E | Back Panel | 1 PC |
| F | Back Panel Strip | 1 PC |
| G | Back Panel | 1 PC |
| H | Top Panel | 1 PC |
| I | Large Shelf | 1 PC |
| J | Small Shelf | 1 PC |
| K | Left Door Panel | 1 PC |
| L | Right Door Panel | 2 PC |
Hardware List
| No. | Description | Quantity |
|---|---|---|
| 01 | Ø8x40mm Bolt | 12+1 PCS |
| 02 | Washer | 12+1 PCS |
| 03 | Shelf Support | 8 PCS |
| 04 | Magnetic Catch | 3 PCS |
| 05 | Ø3x16mm Screw | 42+1 PCS |
| 06 | Ø2.5x14mm Screw | 3+1 PCS |
| 07 | Metal Plate | 3 PCS |
| 08 | Door Handle | 3 PCS |
| 09 | Anti-Tip Device | 2 PCS |
| 10 | Allen Wrench | 1 PC |
| 11 | Hinge | 6 PCS |
| 12 | Rear Panel Hook | 8 PCS |
Assembly Instructions
Note: Please tighten screws after completing all installation.
Step 1: Connect Side Panels to Baseboard
Attach the bottom of Left Side Panel (A) and Right Side Panel (B) to the Bottom Panel (C). Use four Ø8x40mm Bolts (1) with four Washers (2) for each side panel, securing them with the Allen Wrench (10). A close-up shows the bolt and washer placement. A reminder states not to fully tighten screws until assembly is complete.
Diagram shows connecting panels A and B to C using bolts (1) and washers (2), with the Allen wrench (10) for tightening. Two people are recommended for assembly.
Step 2: Attach Middle Partition
Attach the bottom of the Center Divider Panel (D) to the Bottom Panel (C). Use two Ø8x40mm Bolts (1) with two Washers (2) for each side of the partition, securing them with the Allen Wrench (10). A close-up shows the bolt and washer placement.
Diagram shows attaching panel D to panel C using bolts (1) and washers (2).
Step 3: Install Back Panels
Insert the three back panel components: Back Panel (G), Back Panel Strip (F), and Back Panel (E) into the rear grooves of the assembled frame. Pay attention to the orientation differences between panels G and E.
Diagram shows inserting panels E, F, and G into the back of the cabinet structure.
Step 4: Insert Shelf Brackets
Insert two Shelf Supports (8) into the pre-drilled holes in the middle of the Left Side Panel (A), Right Side Panel (B), and Center Divider Panel (D).
Diagram shows inserting shelf supports (8) into side panels A, B, and partition D.
Step 5: Attach Magnetic Catches
On the underside of the Top Panel (H), attach the Magnetic Catches (4) using three Ø3x16mm Screws (5) for each catch. A close-up shows the screw placement.
Diagram shows attaching magnetic catches (4) to the underside of the top panel (H) using screws (5).
Step 6: Attach Top Panel
Align the Top Panel (H) with the top of the assembled cabinet. Secure the Top Panel (H) to the side panels (A, B) and the middle partition (D) using six Ø8x40mm Bolts (1) with six Washers (2), tightened with the Allen Wrench (10).
Diagram shows attaching the top panel (H) to the main cabinet structure using bolts (1) and washers (2).
Step 7: Insert Shelves
Place the Large Shelf (I) and Small Shelf (J) diagonally into the cabinet and level them.
Diagram shows inserting shelves I and J into the cabinet.
Step 8: Install Doors and Hardware
Attach the Left Door Panel (K) and Right Door Panel (L) to the cabinet. Use Ø3x16mm Screws (5) to attach Hinges (11) to the cabinet doors and side panels. Secure Magnetic Catch Plates (4) to the doors using Ø3x16mm Screws (5). Use Ø2.5x14mm Screws (6) to attach the magnetic catches to the cabinet. If doors are misaligned, adjust the bottom screws for levelness. A troubleshooting tip suggests loosening screws on the center divider panel (D) and gently shifting it if doors won't close.
Diagram shows attaching doors K and L using hinges (11), screws (5, 6), and magnetic catches (4). Includes a note on adjusting for alignment.
Step 9: Attach Rear Panel Hooks
Attach eight Rear Panel Hooks (12) to the back of the cabinet using the provided screws.
Diagram shows attaching rear panel hooks (12) to the back of the cabinet.
Step 10: Install Anti-Tip Devices
Attach two Anti-Tip Devices (9) to the top back edge of the cabinet.
Diagram shows attaching anti-tip devices (9) to the top back of the cabinet.
Step 11: Secure to Wall
Secure the Anti-Tip Devices (9) to the wall using appropriate fasteners. A critical WARNING is displayed: 'Children have died from furniture tip-overs. To reduce the risk of furniture tip-overs: Always install the provided tip-over restraint. For use with televisions weighing 200 lbs or less. Using heavier televisions may result in instability, causing tip-overs and resulting in death or serious injury. Never use with CRT televisions. Never allow children to stand, climb, or hang on drawers, doors, or shelves. Never open more than one drawer at a time. Place heaviest items in the lowest drawers. Do not defeat or remove the drawer interlock system.' The label for the anti-tip device states: 'This is a permanent label. Do not remove it!'.
Diagram shows securing the anti-tip device to a wall. Includes a prominent warning about furniture tip-overs.
Maintenance and Care
Prevent Moisture Damage: Safeguard your laminate furniture by keeping it in a dry environment. Store the furniture away from damp areas and water sources.
Sunlight Shielding: Shield your laminate furniture from direct sunlight to prevent color fading and surface deterioration. Consider using curtains or blinds for protection, especially if direct sunlight exposure is unavoidable.
Regular Care: Maintain your laminate furniture's appearance by gently wiping surfaces with a damp cloth. Avoid using overly wet cloths or abrasive cleaning tools.
Avoid Scratches: Protect the furniture surface from scratches by refraining from placing sharp or hard objects on it. When moving the furniture, be cautious not to scrape the legs against the floor.
Proper Weight Distribution: Prevent structural damage by placing heavy objects on stable support surfaces rather than directly on the laminate furniture's surface. This simple step can prolong the life of your furniture.
Warranty Information
Warranty Coverage: Our warranty provides protection against manufacturing defects in materials and workmanship for a specified period from the date of purchase, as outlined in the accompanying warranty documentation.
Exclusions: The warranty does not cover damages resulting from misuse, negligence, accidents, normal wear and tear, unauthorized repairs or modifications, improper assembly, or failure to adhere to the care and maintenance guidelines provided.
Share Your Space
We love to see where our furniture ends up - snap a pic and tag us on Instagram or Facebook for your chance to be featured on our social channels and WIN A PRIZE.
Connect with us: Facebook, Instagram, Pinterest, TikTok