DOD FX86B Death Metal Distortion

What the FX86B Does

The FX86B creates a grinding wall of noise perfect for harmonic corruption. It emulates the death metal and grindcore sounds of bands like Napalm Death, Carcass, Brutal Truth, and Pungent Stench. A key feature is its ability to oscillate when the R.I.P. (LEVEL) control is turned up, allowing oscillation at any amp volume. The distortion level is fixed; there is no separate distortion control.

Connecting the FX86B

Connect your guitar to the input of the FX86B. Connect the output of the FX86B to your amplifier or another effects device. To eliminate the need for a 9-volt battery, attach the DOD PS200R power supply to the AC adapter jack.

Features

• LED indicator shows status of effect and battery condition.
• Active switching for noiseless operation.
• Easy access battery compartment.
• Adapter jack for AC operation.
• Rugged die-cast metal case.
• Three year limited warranty.
• Rubber non-skid bottom.

Controls

R.I.P. (LEVEL)

Matches the distortion level with the original signal level. Turning this control clockwise may cause some varieties of cats to gather and fight with one another. Turning the control counterclockwise can be useful for a little midnight thrashing to avoid an encounter with large numbers of law enforcement personnel.

GUTS (LOW)

Controls the low end of the distortion sound. Turn it up to make your speakers groan.

PAIN (MID)

Controls the mid frequencies of the distortion. Turning it down makes the low end a monster. Turn it up and you will begin to feel the PAIN!

SCREAM (HIGH)

Controls the amount of high end on the distortion. Turn it up for brutal chainsaw pick attack! DOD will not be held responsible for any damage caused by those “formally dead” who are suddenly awakened by the FX86B.

FOOTSWITCH

Switches the distortion effect in or out of the signal path.

LED INDICATOR

Lights when the distortion is enabled, and is not lit when the distortion is bypassed.

JACKS

Input, Output, AC Adapter (use the DOD PS200R power supply to eliminate the need for a 9 volt battery).

Operation of the FX86B

The FX86B is a high-gain effect designed to rattle bones. It features three EQ controls: GUTS (LOW), PAIN (MID), and SCREAM (HIGH). Alternate guitar or bass tunings can enhance the sound; try tuning to C# (C#, F#, B, E, G#, C#) or C (C, F, Bb, Eb, G, C) for a meaner tone.

When setting up the effect, use the R.I.P. (LEVEL) control to match the level of the distortion effect with the level of the original input signal. The control should be set so that there is a slight increase in level when the effect is switched into the signal path.

The GUTS (LOW) knob controls the low-frequency (bass) content of the signal. Turning this control clockwise increases the low frequency content.

The SCREAM (HIGH) knob controls the high-frequency (treble) content of the guitar signal. This control adds more edge to your sound, allowing your guitar sound to shatter glass.

The PAIN (MID) knob controls the mid-frequencies and can make your skin crawl if turned up. When it’s turned down, it makes the GUTS (LOW) and SCREAM (HIGH) controls even more effective.

Examples of different sound settings are provided on the following pages, with graphic representations of knob settings. Use these as starting points to create your own sounds.

Example Sound Settings:

• Destroyer Sound: Dropped mids enhance bass and highs.
• Hard Sound: Slight drop in mids for instant impact.
• Wall of Noise: Ultra low end and blaring highs.

Important Notes

• The FX86B battery is in use whenever the INPUT jack is plugged in. Unplug the cable from the INPUT jack when not in use to prevent unnecessary battery drain.
• Remove the battery when the unit is not going to be used for an extended period to prevent possible damage from leaking battery fluids.
• If the FX86B fails to switch in or out, or the LED indicator stays lit, the battery needs to be replaced.
• Use of any AC adapter other than the DOD PS200R will void the warranty of this product.
• Unauthorized repair of the FX86B will void the warranty. For service, contact your DOD FX pedal dealer for return/repair information.

DOD Warranty

1. The warranty registration card must be mailed within ten days after purchase date to validate this warranty.
2. DOD warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship under normal use and service.
3. DOD liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the product is returned through the original dealer. All parts and labor will be covered up to a period of three years. The company shall not be liable for any consequential damage as a result of the product’s use in any circuit or assembly.
4. Proof-of-purchase is considered to be the burden of the consumer.
5. DOD reserves the right to make changes in design or make additions to or improvements upon this product without incurring any obligation to install the same on products previously manufactured.
6. The foregoing is in lieu of all other warranties, expressed or implied. DOD neither assumes nor authorizes any person to assume for it any obligation or liability in connection with the sale of this product. In no event shall DOD or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control.

Declaration of Conformity

Manufacturer’s Name: DOD Electronics Corporation

Manufacturer’s Address: 8760 S. Sandy Parkway Sandy, Utah 84070, USA

declares that the product:

Product Name: FX86B

Product Options: All (requires a Class II power adapter that conforms to the requirements of EN 60065, EN 60742, or equivalent).

Safety: EN 60065 (1993) IEC65 (1985) with Amendments 1,2,3

EMC: EN 55013: (1990) EN 55020: (1991)

Supplementary Information: The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC as amended by directive 93/68/EEC.

Signed:

DOD Electronics Corporation

President of DOD

8760 S. Sandy Parkway Sandy, Utah 84070, USA

Effective: August 26, 1997

European Contact: Your Local DOD Sales and Service Office or International Sales Office

3 Overlook Drive #4, Amherst, New Hampshire 03031, USA

Tel: (603) 672-4244 Fax: (603) 672-4246

Contact Information

DOD Electronics Corporation

8760 South Sandy Parkway

Sandy, Utah 84070

Telephone: (801) 566-8800

FAX: (801) 566-7005

International Distribution

3 Overlook Drive Unit 4

Amherst, New Hampshire 03031

U.S.A.

FAX: (603) 672-4246

Copyright © 1998 DOD Electronics Corporation

Printed 2/98

FX86B 18-0038-B

A Harman International Company