Baby Trend HC01045 High Chair Instruction Manual
Product Information
Item #: HC01045
Please verify you have all parts listed below for this model before assembling the product.
Parts List
- Seat Back x 1
- Legs x 2
- Height Adjustment Hooks x 2
- Black Screws (3.5 mm x 10) x 4
- Tray for Tableware x 1
- Footrest x 1
- Tray x 1
- 4 Casters x 4
- Upper Frame Assembly x 2
- Cushion x 1
- Hinge Bar at Seat Back x 1
- Storage Basket x 1
- Seat Base x 1
- Activity Tray x 1
- Crotch Strap x 1
Important Safety Instructions
Read all instructions in the manual BEFORE assembly or USE of this product.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
WARNING: Failure to follow these warnings and instructions could result in serious injury or death.
WARNING: To prevent serious injury from slipping or falling, always use the harness. NEVER leave a child unattended.
WARNING: The child must be secured in the high chair at all times by the restraint system, whether in the reclined, inclined, or upright position. The tray is not designed to restrain the child in the chair. It is recommended that the high chair be used in the upright position only by a child who is already able to sit up properly without assistance. See page 8 for instructions on the correct use of the safety system.
Accessories attached to the chair may affect the high chair's balance and make it unstable or dangerous; use only Baby Trend approved toys.
Ensure the high chair is fully upright and locked in the open position before allowing a child nearby.
Using the high chair with a child weighing over 40 pounds may cause excessive wear and stress on the high chair.
The maximum weight that can be carried in the basket is 5 pounds. Excessive weight may affect the stroller's balance and make it unstable or dangerous.
Never allow your high chair to be used as a toy.
NEVER use this product if any fasteners are missing or loose, joints are loose, parts are broken, or fabric is torn. Regularly check your stroller before use. Please contact our Baby Trend customer service at 1-800-328-7363 for replacement parts, to make arrangements for repair, or for questions about the instruction manual. NEVER substitute Baby Trend parts with others.
If you experience difficulties with the use of this product, contact our Customer Service Department at 1-800-328-7363 between 8:00 AM and 4:30 PM Pacific Time. Please have your model number and date of manufacture available when you call. This information can be found on a small sticker under the seat.
Parts Diagram
An illustration shows all the individual parts of the high chair, including the seat back, legs, hooks, screws, trays, footrest, casters, frame assembly, cushion, hinge bar, storage basket, seat base, activity tray, and crotch strap.
Assembly
IMPORTANT! To ensure your stroller operates safely, follow these instructions carefully. Keep these instructions for future reference.
IMPORTANT! Before each assembly and use, inspect this product for damaged material, loose joints, missing parts, or sharp edges. NEVER use if any parts are missing or broken.
IMPORTANT! Assembly by an adult is required.
IMPORTANT! Always ensure the high chair is locked in the open position before use.
ATTENTION: Carefully remove parts from the box. Verify you have all parts for this model before assembling the high chair. NOTE: Some high chair models come with the seat cushion and seat adjuster already attached to the backrest.
To Assemble the Seat
- Place the seat base on a flat surface as shown in Figure 1.
- Attach the seat back to the seat base using the hinge bar as shown in Figure 2. The bar is inserted from right to left, as indicated.
- Slide the height adjustment hooks from the left and right seat onto the seat base (Figure 3). Attach the hooks (Figure 4).
- Slide the footrest onto the seat base as shown in Figure 5. Attach the footrest to the seat base.
- Insert the upper right leg into the frame slot (Figure 6). The front of the tube is easily distinguished from the back by the holes located on the rear of the tube.
- Press the red handle and push the tube into the seat height adjustment hook until it clicks into the highest position (Figure 7).
- Repeat steps 5 and 6 for the left side of the frame (Figure 8).
- Insert the front leg ends from the right and left into the front foot (Figure 9). NOTE: The legs are correctly connected when the fasteners align with the holes on the frame ends. Ensure the fasteners are locked before use.
- Insert the rear leg ends from the right and left into the rear frame (Figure 10).
- Insert each caster into the high chair legs as shown in Figure 11. Attach the casters to the bottom of the feet. Ensure all four wheels are securely attached to the high chair.
- Turn the tray over to insert the crotch strap. The slot should face the front of the tray. Attach with the 4 provided screws (3.5 x 10 mm) and tighten the screws firmly but without overtightening (Figure 12).
To Attach the Seat Cushion
- Pass the flap on the back of the cushion over the top of the seat back. Attach the cushion to the upper part of the backrest with the two elastic loops. These hook over the fasteners located above the upper harness slots (Figure 13).
- Attach the bottom of the cushion to the bottom of the seat with the two elastic loops located on the back of the cushion. These pass over the fasteners located on the seat base, where the rear seat and seat base meet (Figure 14).
- Place the seat adjuster over the cushion.
- Pass the harness strap ends through the slots in the seat fabric, cushion, backrest, and seat base (Figure 15). Once the ends are through the slots, turn them 90 degrees. Ensure the straps are securely attached.
To remove the seat cushion: Reverse the above steps.
Usage
Unfolding the High Chair
Push to spread the legs completely and lock them (Figure 16). Press the folding levers (left and right) to ensure the frame is locked in the open position.
Always ensure the high chair is locked in the open position before use.
The tray is not designed to restrain the child in the chair. The child must always be secured with the safety harness when in the high chair.
Attaching and Using the Tray
To attach the tray, align the grooves on the bottom with the high chair armrests. Pinch the tray handle and slide the tray onto the armrests (Figure 17). The tray can be adjusted to 3 positions. To adjust the position, pinch the tray handle and move the tray to the desired position (Figure 18). Release the tray handle. Ensure the tray is securely locked in its new position.
Attaching the Tray for the Tableware
The food tray (dishwasher safe) inserts into the high chair tray and is held in place by clips on the side of the tray. When installing the food tray, ensure it is securely fastened to prevent the child from removing it. To remove the tray, release the tabs on the tray.
Reclining the Seat
Press the lever on the back of the seat and adjust the recline or set to the upright position (Figure 19). When adjusting the seat position, be very careful not to pinch the child's arms, hands, or legs.
It is recommended that the high chair be used in the upright position only by a child who is already able to sit up properly without assistance.
To prevent death or serious injury from slipping or falling. Always use the safety harness, whether in the reclined, inclined, or upright position.
To Use the Safety Harness
The tray is not designed to restrain the child in the chair. Always keep the child in view while in the high chair. NEVER LEAVE A CHILD UNATTENDED.
- Pass your child's arms through the loops formed by the shoulder and waist straps. Place the crotch strap between your child's legs. Insert the buckles into the center buckle with the red button.
- Adjust the straps for your child's comfort and security by sliding the buckles in both directions. The safety straps should be snug around your child (Figure 20).
Releasing the Safety Harness
Press the red button in the center of the buckles, and the two straps will release (Figure 21).
Adjusting the Seat Height
Do not adjust the seat height with a child in the seat. Adjust the seat height before placing your child in the high chair.
Press the height adjustment buttons on the left and right sides and adjust to the desired position (Figure 22).
Always ensure the support height adjustment is the same on the right and left sides and that both sides are locked before placing the child in the high chair.
Folding the High Chair
The high chair can be folded with the seat in any position. The high chair will be most compact when the seat is in the lowest position.
- Set the seat to the desired position (Figure 23).
- Place the seat back in the most upright position (Figure 19).
- Pinch the tray handle and slide it (Figure 17). Hook the tray onto the brackets located on the rear of the legs (Figure 23).
- Pull up on the levers located on the sides of the frame and push the rear legs towards the front legs until they are folded (Figure 24). The chair is now ready for storage.
DO NOT allow your child to play near a folded high chair as it may fall.
To Unfold the High Chair
Spread the legs until they are fully open and lock. Push down on the levers on the left and right to securely lock the frame (Figure 16).
Care and Maintenance
Attaching or Removing a Toy
Attaching or Removing the Musical Toy: The musical toy (part no. 16) attaches using the suction cup on the bottom of the toy. To attach, simply press the toy onto the tray so the suction cup adheres; to remove, lift a part of the bottom of the suction cup.
Attaching or Removing the Teether Toy: Insert the teether toy attachment (part no. 17) into the slot on the side of the tray and attach the bottom of the toy to the lower edge of the tray. Reverse the procedure to remove the toy (Figure 25).
Care Instructions
WARNING: The harness straps and storage basket are NOT washable.
The Tray for the Tableware
The tray is dishwasher safe at 160 degrees Fahrenheit. Do not use abrasive sponges on the tray as they will damage the surface and make the tray difficult to clean.
High Chair / Tray
Clean the high chair after each use using a mild dish soap. Use only a soft-bristled brush, sponge, or cloth to clean food crumbs from the surface. DO NOT submerge the chair or tray in water; clean the surface only.
Seat Cushion
(Please refer to the label on the seat cushion for cleaning instructions)
To remove the cushion: Remove the straps by passing them through the holes in the cushion, backrest, and seat base from which they came. Detach the elastic loops from the fasteners that hold the seat to the backrest and seat base.
Non-washable Seat Cushion: Please use only a sponge or cloth with mild dish soap to clean the surface. DO NOT PUT THE SEAT ADJUSTER IN THE WASHING MACHINE.
Washable Seat Cushion: Machine wash in COLD water on the DELICATE cycle with a laundry detergent that does not contain chlorine. DO NOT USE BLEACH. AIR DRY. DO NOT TUMBLE DRY.
To Attach or Detach the Storage Basket
NOTE: Some models have a storage basket under the seat. On these models, the basket is already attached to the seat base.
To detach the storage basket: The basket is attached with four clips. Detach the clips to remove the basket.
To attach the storage basket: Pass the clips through the slots in the seat base. Press firmly on the clips to lock them.
For contact information and support, please visit: www.babytrend.com
