Baby Trend Kid Café Snap Fit™ 3-in-1 High Chair

Warranty Information

Baby Trend® offers a warranty covering workmanship defects for the first 180 days from purchase. This warranty is void if the product is subjected to misuse, abuse, abnormal use, excessive wear and tear, improper assembly, negligence, environmental exposure, alteration, accident, or if the serial number has been altered or removed. Any property damage during installation is the end user's sole responsibility. For warranty service or replacement parts, contact Baby Trend Customer Service at 1 (800) 328-7363, Monday through Friday, 8:00 AM to 4:30 PM PST. Return authorizations are required. Warranty is valid only in North America.

Parts List

Before assembly, check that you have all the parts for this model:

• Booster Seat
• Seat Pad
• Harness Covers (X2)
• Upper Frame Assemblies (X2)
• Height Adjuster
• Legs (X2)
• Casters (X4)
• Footrest
• Tray
• Tray Insert

Safety Warnings

General Warnings

• ⚠️ Failure to follow these warnings and instructions could result in serious injury or death.
• ⚠️ Prevent serious injury or death from falls or sliding out. Always use the restraint system.
• ⚠️ Never leave the child unattended. Always keep your child in view while in this product.
• ⚠️ Never allow a child to push away from tables.
• ⚠️ Never lift or move the high chair with a child in it.
• ⚠️ Do not use this product if it is damaged or broken.
• ⚠️ Do not use in motor vehicles.

Strangulation Hazard

• ⚠️ Do not place the High Chair in any location where there are cords, such as window blind cords, drapes, or phone cords.

Booster Seat Specific Warnings

• ⚠️ Children have suffered head injuries, including skull fractures, after falling with or from booster seats.
• ⚠️ Always secure the booster seat to an adult chair before each use.
• ⚠️ Always use restraints until the child can get in and out of the booster seat without help (approximately 2.5 years old). Adjust restraints for a snug fit.
• ⚠️ Never allow a child to push away from the table.
• ⚠️ Never lift and carry a child in the booster seat.
• ⚠️ Always stay near and watch your child during use.
• ⚠️ Always check the security of the fit to the adult chair before each use and be aware of product limitations.
• ⚠️ Never use this product on a stool or bench that does not have a seat back.
• ⚠️ The tray is not designed to hold the child in the chair.
• ⚠️ It is recommended that the booster seat be used in the upright position only by children capable of sitting upright unassisted.
• ⚠️ Always secure the Booster Seat on a chair using the bottom and back attachment straps.
• ⚠️ Minimum adult chair size for attachment: Width: 16.1 inches, Depth: 16.9 inches, Backrest height: 4.7 inches.

Infant Car Seat Specific Warnings

• ⚠️ To avoid serious injury from falling or sliding out, always use the Infant Car Seat harness.
• ⚠️ Do not adjust car seat height with a child in the seat. Adjust seat height before placing your child in the car seat.
• ⚠️ Always check that the Height Adjustment Bracket is level and both left and right sides are locked before placing a child in the car seat.
• ⚠️ Never use the car seat mode at higher positions; always use it at the lowest position.
• ⚠️ Never rest the height adjustment bracket on the locking pins.

Assembly Instructions

IMPORTANT: To ensure safe operation, follow these instructions carefully and keep them for future reference.

IMPORTANT: Before assembly and each use, inspect the product for damaged hardware, loose joints, missing parts, or sharp edges. NEVER use if any parts are missing or broken.

IMPORTANT: Adult assembly is required.

IMPORTANT: Always check that the high chair is locked in the open position before using.

ATTENTION: Carefully remove parts from the box. Check that you have all parts for this model before assembling.

Assembling the Frame

1. Take the left and right Upper Frame Assemblies. Push the legs apart until fully open and locked. Push down on the fold levers (left and right) to ensure the frame is locked open. [See Figure 1a]
2. Insert the front tube of the right and left side Upper Frame Assemblies into the Height Adjuster. The front tube is distinguished by holes on its backside. [See Figure 1b]
3. Squeeze the Release Handles on both sides simultaneously and push the tube through the Height Adjusters until it locks in the highest position. [See Figure 2]
4. Insert the legs into the ends of the Front tube of both Upper Frame Assemblies. Ensure legs are properly connected by checking that locking pins align with holes. [See Figure 3a]
5. Insert the remaining legs into the ends of the Rear tube of both Upper Frame Assemblies. Ensure legs are properly connected by checking that locking pins align with holes. [See Figure 3b]
6. Attach each Caster to the high chair leg by snapping them into the bottom of the leg. Verify all four Casters are securely fastened. [See Figure 4]

Assembling the Booster Seat

1. Slide Footrest posts into the front of the Seat until they click into place. [See Figure 5a]
2. Connect the Seat and lock it into place. Pull up to ensure it is firmly locked before use. [See Figure 5b, 5c]

Attaching the Tray

WARNING: Always check that the high chair is locked in the open position before using.

WARNING: The tray is not designed to hold the child in the chair. The child must be secured by the 5-point restraining system at all times.

6. To attach the Tray, align the grooves on the bottom of the tray with the high chair armrests. Squeeze the front release handle and slide the tray onto the armrests. [See Figure 6a]

The tray has a 2-position adjustment. To adjust, squeeze the front release handle under the tray, reposition, and release the handle. Ensure the tray is securely locked.

ATTENTION: Never leave the tray in a position where warning signs are visible. [See Figure 6b]

Attaching the Insert Tray

7. The dishwasher-safe Tray Insert snaps onto the High Chair Tray, held by side tabs. Ensure it snaps securely to prevent the child from removing it. To remove, unsnap the tabs. [See Figure 7a]
8. The tray can be stored on the back legs of the High Chair by aligning its rear holes with the pegs on the back legs. [See Figure 7b]

Attaching the Infant Car Seat

25. Connect the infant car seat and lock it into place. Ensure it is firmly locked before use. [See Figure 25a, 25b]

Removing the Infant Car Seat

26. Detach the infant car seat from the upper frame assembly by pushing the center buttons on each side of the seat and lifting the seat upwards. [See Figure 26]

Reattaching the Seat Pad

22. Thread the non-buckle end of the Harness Straps (Harness Attachment Tabs) through the slots in the seat fabric, seat back, and seat base. Rotate the tabs 90 degrees once through the slots to ensure they are firmly in place. [See Figure 22a, 22b]
23. Loop the flap on the back of the pad over the top of the seat back. Connect the seat pad to the seat back using the two elastic loops that fit over the attachment tabs near the top harness slots. [See Figure 23a, 23b]
24. Insert the Harness Covers through the Harness Straps. [See Figure 23c]

Removing the Seat Pad

Reverse the above steps.

Operation

Using the Safety Belt

WARNING: It is recommended that only children capable of sitting upright unassisted use the high chair in the upright position.

The tray is not designed to hold the child. Always keep the child in view. Never leave the child unattended.

1. The 5-point harness shoulder straps have two attachment positions. Select the position that places the shoulder strap level with, or below, the top of the child's shoulder. [See Figure 8a]
2. Carefully place the child in the seat. Position the safety harness around the child's waist and over the shoulders. Place the crotch strap between the child's legs. Insert the male ends of the shoulder/waist belts into the crotch strap buckle. Tighten the harness snugly around the child's waist and over the shoulders. [See Figure 8b]

Releasing the Child

9. To release the harness, push the button on the Center Clasp. The two harness buckles will pop free. [See Figure 9]

Reclining the Seat

10. Squeeze the recline lever on the back of the seat and adjust to the desired recline or upright position. Use caution not to trap arms, hands, or fingers when adjusting. [See Figure 10]

Adjusting Seat Height

WARNING: Do not adjust seat height with a child in the seat. Adjust before placing the child.

WARNING: Always check that the height adjustment bracket is level and both sides are locked before placing the child.

WARNING: Never rest the height adjustment bracket on the locking pins.

11. Squeeze the Release Handles on both sides simultaneously and adjust to the ideal position. [See Figure 11a, 11b]

ATTENTION: Ensure Height Brackets lock in the lowest position. Do NOT rest them on the locking pins. [See Figure 11c]

Adjusting the Footrest

12. Press the buttons on both sides of the footrest to adjust it up or down. [See Figure 12]

Brakes

13. To engage brakes, apply downward pressure to the brake tabs. Check that the high chair does not move and brakes are properly applied. To release, lift the brake tabs. [See Figure 13]

Folding the High Chair

The high chair can be folded with the seat in any height position.

14. Place the seat in the desired height position. Place the seat back in the most upright position. [See Figure 14]
15. Squeeze the tray release handle and slide the tray out. [See Figure 15]
16. Hang the tray on the pegs located on the back of the rear leg. [See Figure 16]
17. Pull upward on the release levers (on the sides of the frame) and push the rear legs towards the front legs until folded. The chair is now ready to be stored. This is not a toy. Do NOT allow your child to play around a folded high chair. [See Figure 17]

Unfolding the High Chair

Reverse the above steps.

Attaching the Booster Seat to the Chair

WARNING: Always secure the booster seat to a chair using the bottom and back attachment straps. Never use on a stool or bench without a seat back.

18. Detach the seat from the upper frame assembly by pushing the center buttons on each side and lifting the seat upwards. [See Figure 18]
19. Remove the footrest by pushing the release button on each side and pulling the footrest out of the seat. [See Figure 19]
20. Turn the booster seat over. Slide open the strap compartments on the bottom. [See Figure 20a]
21. Pull straps out of the compartment. Place the booster seat onto a chair with a seat back and no armrests. Ensure there are no extra paddings or cushions on the chair. [See Figure 20b]
22. Wrap the back straps around the chair back. Buckle straps, ensuring they click closed. [See Figure 20c]
23. Pull the free ends of the straps to firmly tighten the booster seat to the chair. [See Figure 20d]
24. Wrap bottom straps around the chair bottom. Buckle straps, ensuring they click closed. [See Figure 20e]
25. Pull the free ends of the straps to firmly tighten the booster seat to the chair. [See Figure 20d]
26. Check for tight installation by trying to move the booster seat side-to-side and up. It should not move more than 1 inch.

Removing the Booster Seat from the Chair

21. Unbuckle the back and bottom straps (refer to Step 20). Turn the booster seat over. Slide open the strap compartments on the bottom. [See Figure 21a]
22. Fold the straps and place them in the compartment, then slide the compartment door closed. [See Figure 21b]

Adjusting the Infant Car Seat Height

WARNING: Do not adjust car seat height with a child in the seat. Adjust height before placing the child.

WARNING: Always check that the height adjustment bracket is level and both sides are locked before placing the child.

WARNING: Never use the car seat mode at higher positions; always use it at the lowest position.

WARNING: Never rest the height adjustment bracket on the locking pins.

24. Squeeze the left and right Release Handles of the height adjustment bracket and adjust to the lowest position. Do NOT adjust with a child in the seat. [See Figure 24a]

ATTENTION: The Height Adjustment Bracket must be set at the lowest position before placing the car seat. [See Figure 24b]

Care and Maintenance

WARNING: Harness Straps and Basket are NOT washable.

Dishwasher Safe Tray Insert

The Tray Insert is dishwasher safe up to 160° F (71° C). Do not use scouring pads on the Tray Insert as they will damage the surface and make it harder to clean.

High Chair/Tray

Use mild soap and wash with a damp cloth after each use. Use only a soft bristle brush, sponge, or cloth to clean the surface or remove food particles. DO NOT submerge the high chair or tray in water. Surface clean only.

Seat Pad

To remove the seat pad: Remove Harness Straps by pushing Harness Attachment Tabs through the harness slots on the seat back, seat base, and seat pad. Remove elastic loops from attachment tabs on the seat base and seat back.

To attach the seat pad: Follow instructions in Step 22 for correctly re-threading the safety harness. (For cleaning the seat pad, body insert, and harness covers, refer to the care label on the seat pad).

Non-Washable Seat Pad: Use mild soap and wipe with a damp cloth. NOT MACHINE WASHABLE.

Washable Seat Pad: Machine wash COLD DELICATE CYCLE with non-chlorine based laundry detergent. DO NOT USE BLEACH. HANG DRY. DO NOT MACHINE DRY.

Infant Car Seat Mode

The car seat can face either direction (front or backwards).

Infant car seat sold separately.