Home Decorators Collection 1-Light Pendant

Thank You

We appreciate the trust and confidence you have placed in Home Decorators Collection through the purchase of this 1-light pendant. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Home Decorators Collection!

Safety Information

Read all instructions before assembling and installing.

Consult a qualified electrician for installation of this fixture.

If you have any non-electrical questions about this fixture, please contact our Customer Service Team at 1-800-986-3460 or visit www.homedepot.com/homedecorators.

Please reference your SKU 1001 xxx xxx or UPC 773546xxxxxx.

Keep your receipt and these instructions for proof of purchase.

Warranty

LIMITED WARRANTY

WHAT IS COVERED

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer's only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer's discretion, provided that the product has not been damaged through misuse, abuse, accident, modification, alteration, neglect, or mishandling.

WHAT IS NOT COVERED

This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the replacement or repair of said product.

Contact Customer Care at 1-800-986-3460 or visit www.homedepot.com/homedecorators.

Pre-Installation

PLANNING INSTALLATION

Read all instructions before assembly and installation. To avoid damaging this product, assemble it on a soft, non-abrasive surface, such as carpet or cardboard. Inspect each part for defects that may have occurred during shipping. Keep your receipt and these instructions for proof of purchase.

TOOLS REQUIRED

• Safety goggles
• Measuring tape
• Phillips screwdriver
• Flathead screwdriver
• Wire strippers
• Wire cutters
• Ladder
• Electrical tape

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

Package Contents

The package includes the main fixture body (A), three rods (B) for adjusting height, and a canopy (C) for mounting.

Installation

1. 1. Removing the crossbar

   Unlock the mounting screws (DD) from the crossbar (BB) and remove the crossbar (BB) from the canopy (C).

   Diagram shows the crossbar (BB) with mounting screws (DD) and the canopy (C).

2. 2. Installing the crossbar

   ⚠️ WARNING: Turn the power off at the main fuse box before installation.

   Attach the crossbar (BB) to the junction box (not included) with the two outlet box screws (CC) provided.

   Diagram illustrates the crossbar (BB) being attached to a junction box using outlet box screws (CC).

3. 3. Installing the fixture body

   Thread the fixture wire up through a rod (B), then tighten to the fixture body (A). Determine the desired length of the item, adding the other rod (B) as needed.

   Thread the fixture wire from the rod (B) up through the canopy (C), then attach the canopy (C) to the assembly until tight.

   Diagram depicts the fixture body (A) connected to rods (B), with wires threaded through to the canopy (C).

4. 4. Making the electrical connections and locking the canopy

   NOTE: Always use wire nuts (AA) or marrettes (included) to connect wires and push all excess wires and connections back into the junction box.

   Connect the ground wire from the branch circuit to the green ground screw (EE) on the crossbar (BB) and add 6 in. for the ground connection.

   Connect the fixture wires as follows:

   • White wire from fixture to white wire from house.
   • Black wire from fixture to black wire from house.
   • Bare ground wire from fixture to ground screw or ground wire from house.

   Attach the canopy (C) to the crossbar (BB), and secure it with the mounting screws (DD).

   Diagram shows the electrical connections: white wire to white wire, black wire to black wire, and ground wire to the green ground screw (EE) on the crossbar (BB). It also shows the canopy (C) being secured with mounting screws (DD).

5. 5. Installing the bulbs

   ⚠️ CAUTION: Oil from fingers will decrease the life of the 60W max ST64 Edison bulb (included).

   With a tissue or glove (not included), install 60W max ST64 Edison bulb (FF) into the socket of the fixture body (A).

   Diagram shows the fixture body (A) with the bulb (FF) being installed into the socket.

Care and Cleaning

Clean the light fixture carefully with a soft, dry cloth. Do not use any cleaner with chemicals, solvents, or harsh abrasives.

Troubleshooting