Safety Information
Read all instructions before assembling and installing. Consult a qualified electrician for installation of this fixture. For non-electrical questions, contact Customer Service at 1-800-986-3460 or visit www.homedepot.com/homedecorators. Reference SKU 1003 427 725 (UPC 773546288118). Keep your receipt and these instructions for proof of purchase.
CAUTION: Before starting installation or removing a previous fixture, disconnect power by turning off the circuit breaker or removing the fuse at the fuse box.
IMPORTANT: Do not install this lighting system in damp or wet locations.
IMPORTANT: Inspect wire insulation for cuts, abrasions, or exposed copper. If a defect is found, do not proceed. Call Customer Service at 1-855-HD-HAMPTON.
Warranty
LIMITED WARRANTY
WHAT IS COVERED: The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for three (3) years from the date of purchase. This warranty applies only to the original consumer purchaser for products used in normal use and service. If the product is found defective, the manufacturer's sole obligation and your exclusive remedy is repair or replacement at the manufacturer's discretion, provided the product has not been damaged through misuse, abuse, accident, modification, alteration, neglect, or mishandling.
WHAT IS NOT COVERED: This warranty does not apply to products improperly installed, set-up, or used contrary to instructions. It does not cover failures due to accident, misuse, abuse, negligence, alteration, faulty installation, or other issues not related to faulty material or workmanship. The warranty does not apply to the finish, which is subject to normal wear and tear. The manufacturer disclaims any warranty of fitness for a particular purpose beyond the stated warranty. The manufacturer is not liable for consequential or incidental loss or damage, including labor/expense costs for replacement or repair.
Contact Customer Care at 1-800-986-3460 or visit www.homedepot.com/homedecorators.
Pre-Installation
PLANNING INSTALLATION: Read all instructions before assembly and installation. Assemble on a soft, non-abrasive surface like carpet or cardboard to avoid damage. Inspect each part for shipping defects. Keep your receipt and instructions.
Tools Required
A description of the tools required:
- Safety goggles
- Phillips screwdriver
- Flathead screwdriver
- Wire strippers
- Wire cutters
- Ladder
Hardware Included
The following hardware is included (note: hardware not shown to actual size):
- AA Wire nut (Quantity: 5)
- BB Outlet box screw (Quantity: 2)
- CC Ground screw (Quantity: 1)
- DD Mounting screw (Quantity: 2)
- EE Universal crossbar (Quantity: 1)
Package Contents
The following parts are included in the package:
- A Fixture body (Quantity: 1)
- B Center rod B (Quantity: 1)
- C Center rod C (Quantity: 1)
- D Center rod D (Quantity: 1)
- E Center rod E (Quantity: 1)
- F Canopy (Quantity: 1)
- G Small glass (Quantity: 1)
- H Large glass (Quantity: 1)
An illustration shows the assembly of the fixture body, center rods, and canopy.
Installation
1. Installing the Center Rods
WARNING: Turn off power at the main fuse box.
Carefully unpack the fixture and lay out all parts on a clean surface. Unfold the fixture arms. Unravel the supply power and ground wires and pass them through the center hole of the rods (B, C, D, E) and the canopy (F). Install center rods (B, C, D, E) and the canopy (F) by twisting each piece clockwise.
2. Making the Electrical Connections
NOTE: Always use wire nuts (AA) to connect wires and push excess wires and connections back into the canopy (F).
Connect the red wire of the driver to the red wire of the fixture. Connect the blue wire of the driver to the blue wire of the fixture.
Diagram illustrates connecting the red wire from the driver to the red wire of the fixture, and the blue wire from the driver to the blue wire of the fixture.
Connect the fixture wires as follows:
- Red wire from driver to red wire from fixture.
- Black wire from driver to black wire from fixture.
3. Installing the Universal Crossbar
WARNING: Turn off power at the main fuse box.
Secure the universal crossbar (EE) to the junction box (not included) with the two outlet box screws (BB).
4. Making the Electrical Connections
NOTE: Always use wire nuts (AA) to connect wires and push excess wires and connections back into the junction box (not included).
Connect the ground wire from the branch circuit to the ground screw (CC) on the universal crossbar (EE).
Connect the fixture wires as follows:
- White wire from house to white wire from fixture.
- Black wire from house to black wire from fixture.
- Ground wire from house to ground wire from canopy.
5. Installing the Canopy
Install the canopy (F) in the universal crossbar (EE) with mounting screws (DD).
6. Installing the Glass
Using the diagram as a reference, install the small glass (G) and large glass (H) to the fixture body (A) and twist clockwise to secure in place.
FCC Statement
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Care and Cleaning
Clean the light fixture carefully with a soft, dry cloth. Do not use any cleaners with chemicals, solvents, or harsh abrasives.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| The bulb will not light. | The bulb is burned out. The power is off. The circuit breaker is off. | Replace the light bulb. Ensure that the power supply is turned on. Ensure that the circuit breaker is set to the ON position. |
| The fuse blows or the circuit breaker trips when the light is turned on. | There are too many items on one circuit. | Unplug the other items on the circuit. Contact a qualified electrician or call Customer Service at 1-800-986-3460. |
Contact Information
Questions, problems, or missing parts? Before returning to the store, call Home Decorators Collection Customer Service:
8 a.m. - 7 p.m., EST, Monday – Friday | 9 a.m. - 6 p.m., EST, Saturday
1-800-986-3460
Visit: www.homedepot.com/homedecorators
Retain this manual for future use.
