Safety Information
Read all instructions before assembling and installing.
Consult a qualified electrician for installation of this fixture.
If you have any non-electrical questions about this fixture, please contact our Customer Service Team at 1-800-986-3460 or visit www.homedepot.com/homedecorators.
Please reference your SKU 1001 xxx xxx or UPC 773546xxxxxx.
Keep your receipt and these instructions for proof of purchase.
[warning-symbol] DANGER: Risk of electrical shock. Disconnect power before installation.
[warning-symbol] IMPORTANT: Inspect the wire insulation for any cuts, abrasions, or exposed copper that have occurred during shipping. If there is a defect in the wire, do not continue the installation process. Please call our Customer Service Team at 1-800-986-3460.
Warranty
Limited Warranty
What is Covered
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer's only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer's discretion, provided that the product has not been damaged through misuse, abuse, accident, modification, alteration, neglect, or mishandling.
What is Not Covered
This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the replacement or repair of said product.
Contact Customer Care at 1-800-986-3460 or visit www.homedepot.com/homedecorators.
Pre-Installation
Planning Installation
Read all instructions before assembly and installation. To avoid damaging this product, assemble it on a soft, non-abrasive surface, such as carpet or cardboard. Inspect each part for defects that may have occurred during shipping. Keep your receipt and these instructions for proof of purchase.
Tools Required
- Safety goggles
- Measuring tape
- Phillips screwdriver [plus-symbol]
- Flathead screwdriver
- Wire strippers
- Wire cutters
- Ladder
- Electrical tape
Hardware Included
NOTE: Hardware not shown to actual size.
| Part | Description | Quantity |
|---|---|---|
| AA | Wire nut | 3 |
| BB | Crossbar | 1 |
| CC | Outlet box screw | 2 |
| DD | Mounting screw | 2 |
| EE | Green ground screw | 1 |
| FF | ST64 60W Edison bulb | 5 |
Package Contents
| Part | Description | Quantity |
|---|---|---|
| A | Fixture body | 1 |
| B | Rod | 3 |
| C | Canopy | 1 |
Diagram shows the main fixture body (A), three connecting rods (B), and the canopy (C) with attached wires.
Installation
Step 1: Removing the crossbar
Unlock the mounting screws (DD) from the crossbar (BB), and remove the crossbar (BB) from the canopy (C).
Diagram shows the crossbar (BB) and canopy (C) with mounting screws (DD) indicated.
Step 2: Installing the crossbar
[warning-symbol] WARNING: Turn the power off at the main fuse box before installation.
Attach the crossbar (BB) to the junction box (not included) with the two outlet box screws (CC) provided.
Diagram shows the crossbar (BB) being attached to a junction box using outlet box screws (CC).
Step 3: Installing the fixture body
Thread the fixture wire up through a rod (B), then tighten to the fixture body (A). Determine the desired length of the item, adding the other rod (B) as needed.
Thread the fixture wire from the rod (B) up through the canopy (C), then attach the canopy (C) to the assembly until tight.
Diagram illustrates threading wires through rods (B) and attaching the fixture body (A) and canopy (C).
Step 4: Making the electrical connections and locking the canopy
NOTE: Always use wire nuts (AA) or marrettes (included) to connect wires and push all excess wires and connections back into the junction box.
Connect the ground wire from the branch circuit to the green ground screw (EE) on the crossbar (BB) and add 6 in. for the ground connection.
Connect the fixture wires as follows:
Diagram shows wire connections: White wire from fixture to white wire from house. Black wire from fixture to black wire from house. Bare ground wire from fixture to ground screw or ground wire from house.
Attach the canopy (C) to the crossbar (BB), and secure it with the mounting screws (DD).
Diagram shows the canopy (C) being attached to the crossbar (BB) with mounting screws (DD), with wire nuts (AA) and ground screw (EE) visible.
Step 5: Installing the bulbs
[warning-symbol] CAUTION: Oil from fingers will decrease the life of the 60W max ST64 Edison bulb (included).
With a tissue or glove (not included), install 60W max ST64 Edison bulbs (FF) into each socket of the fixture body (A).
Diagram shows bulbs (FF) being installed into the sockets of the fixture body (A).
Care and Cleaning
Clean the light fixture carefully with a soft, dry cloth. Do not use any cleaner with chemicals, solvents, or harsh abrasives.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| The bulb will not light. | The bulb is burned out. The power is off. |
Replace the light bulb. Ensure that the power supply is turned on. |
| The fuse blows or the circuit breaker trips when the light is turned on. | The circuit breaker is off. There are too many items on one circuit. |
Ensure that the circuit breaker is set to the ON position. Unplug the other items on the circuit. Contact a qualified electrician or call the Customer Service Team at 1-800-986-3460. |
