Home Decorators Collection 3-Light Semi-Flushmount
Item #1001 xxx xxx | Model #31820-HB
Safety Information
- Read all instructions before installing.
- Consult a qualified electrician for installation of this fixture.
- If you have any non-electrical questions about this fixture, please contact our Customer Service Team at 1-800-986-3460 or visit www.homedepot.com/homedecorators.
- Please reference your SKU 1001 xxx xxx or (UPC 773546292887).
- Keep your receipt and these instructions for proof of purchase.
⚠️ CAUTION: Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box.
ℹ️ IMPORTANT: Do not install this lighting system in a wet location.
ℹ️ IMPORTANT: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not continue the assembly process. Please call our Customer Service Team at 1-800-986-3460.
Warranty
Limited Warranty
What is Covered
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer's only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer's discretion, provided that the product has not been damaged through misuse, abuse, accident, modification, alteration, neglect, or mishandling.
What is Not Covered
This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the replacement or repair of said product.
Contact Customer Care at 1-800-986-3460 or visit www.homedepot.com/homedecorators.
Pre-Installation
Planning Installation
Read all instructions before assembly and installation. To avoid damaging this product, assemble it on a soft, non-abrasive surface, such as carpet or cardboard. Inspect each part for defects that may have occurred during shipping. Keep your receipt and these instructions for proof of purchase.
Tools Required
- Safety goggles
- Measuring tape
- Phillips screwdriver
- Flathead screwdriver
- Wire strippers
- Spanner
- Wire cutters
- Ladder
- Electrical tape
Hardware Included
NOTE: Hardware not shown to actual size.
Diagram showing various hardware pieces labeled AA through KK.
| Part | Description | Quantity |
|---|---|---|
| AA | Wire nut | 3 |
| BB | Outlet box screw | 2 |
| CC | Ground screw (preassembled) | 1 |
| DD | Mounting screw (preassembled) | 2 |
| EE | Crossbar | 1 |
| FF | Collar | 1 |
| GG | Ball nut (preassembled) | 2 |
| HH | Hex nut | 1 |
| II | Lock washer | 1 |
| JJ | Plain washer | 1 |
| KK | Stem | 1 |
Package Contents
Diagram showing the main components of the fixture: A (Fixture body), B (Bushing), C (Canopy).
| Part | Description | Quantity |
|---|---|---|
| A | Fixture body | 1 |
| B | Bushing | 1 |
| C | Canopy | 1 |
Installation
1. Installing the Fixture Body
- Carefully unpack the fixture. Lay out all the parts on a clean surface.
- Unravel the supply power and ground wires and pass them through the center holes of the stem (KK) into the coupling at the center of the fixture body (A).
- Twist the stem (KK) onto the top of the fixture body. Then place the bushing (B) over the stem (KK).
- Place the flat collar (FF), followed by the canopy (C), plain washer (JJ) and lock washer (II). Then secure this assembly in place using the hex nut (HH).
2. Installing the Crossbar
⚠️ WARNING: To reduce the risk of electrical shock, turn the power off at the main fuse box before installation.
- Remove the crossbar (EE) from the canopy (C) by loosening the two ball nuts (GG) on the canopy (C).
- Attach the crossbar (EE) to the junction box (not included) with the outlet box screws (BB).
Diagram showing the crossbar (EE) being attached to the junction box with screws (BB). Components C and GG are also shown.
3. Connecting the Wires
? NOTE: Always use wire nuts (AA) (included) to connect wires and push all excess wires and connections back into the junction box.
- Push all slack fixture wire through the canopy (C) and into the outlet box. Trim the excess fixture wire, leaving a minimum of 6 inches hanging out of the outlet box.
- Connect the ground wire from the branch circuit to the ground screw (CC) on the crossbar (EE).
- Connect the wires as follows:
Diagram illustrating wire connections. Shows house wires (White, Black, Ground) connecting to fixture wires (White, Black, Ground from canopy) using wire nuts (AA). Components EE, CC, and C are visible.
Installation (continued)
4. Installing the Fixture Body
- Install the canopy (C) to the crossbar (EE) by securing the two ball nuts (GG) to the two mounting screws (DD).
Diagram showing the canopy (C) being attached to the crossbar (EE) using ball nuts (GG) and mounting screws (DD).
5. Installing the Bulbs
- Install three 60W max. B10 bulbs (not included) to the socket of the fixture body (A).
Diagram showing a bulb being screwed into a socket on the fixture body (A).
Care and Cleaning
- Clean the light fixture carefully with a soft, dry cloth. Do not use any cleaners with chemicals, solvents, or harsh abrasives.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| The bulb will not light. | The bulb is burned out. | Replace the bulb with a new 60W max. B10 bulb. |
| The bulb will not light. | The power is off. | Ensure that the power supply is turned on. |
| The bulb will not light. | The circuit breaker is off. | Ensure that the circuit breaker is set to the ON position. |
| The fuse blows or the circuit breaker trips when the light is turned on. | There are too many items on one circuit. | Unplug the other items on the circuit. Contact a qualified electrician or call the Customer Service Team at 1-800-986-3460. |
Contact Information
Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service.
Hours: 8 a.m. - 7 p.m., EST, Monday - Friday; 9 a.m. - 6 p.m., EST, Saturday
Phone: 1-800-986-3460
Website: www.homedepot.com/homedecorators
Retain this manual for future use.
