Home Decorators Collection 4-Light Bath Fixture

Safety Information

WARNING: Disconnect the power prior to removing or installing a light fixture.

• Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box.
• Consult a qualified electrician if you have any electrical questions or need to replace the driver.
• If you have any non-electrical questions about this fixture, please contact our Customer Service Team at 1-800-986-3460 or HOMEDEPOT.CA.

Warranty

What is Covered

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of three (3) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer's only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer's discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect or mishandling.

What is Not Covered

This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear.

The manufacturer does not warrant and specially disclaims any warranty, whether expressed or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the replacement or repair of said product.

Contact the Customer Service Team at 1-800-986-3460 or visit HOMEDEPOT.CA.

Pre-Installation

Planning the Installation

Read all instructions before assembly and installation. Before starting installation of the fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box. To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard.

NOTE: Keep your receipt and these instructions for Proof of Purchase.

Tools Required

• Phillips Screwdriver
• Flathead Screwdriver
• Wire Cutter
• Wire Stripper
• Electrical Tape
• 4 60W Incandescent Bulbs (or CFL or LED equivalent)
• Ladder
• Safety Goggles

Hardware Required

NOTE: Hardware not shown to actual size.

Package Contents

Part A: Fixture Body (1), Part B: Glass Shade (4)

Installation

1. Mounting the Hardware

1. Thread the fixture screws (EE) into the provided holes of the mounting bracket (GG).
2. Thread the hex nuts (BB) onto the fixture screws (EE). Do not tighten the hex nuts (BB) at this time.
3. Pull the supply wires out from the outlet box and mount the mounting bracket (GG) to the outlet box using the mounting screws (DD).
4. Place the fixture body (A) over the outlet box and onto the fixture screws (EE).
5. Adjust the fixture screws (EE) until they protrude out from the fixture body (A) 1/4 in.
6. Remove the fixture body (A) and secure the position of the fixture screws (EE) by tightening the hex nuts (BB) against the mounting bracket (GG).

2. Connecting the Wires

NOTE: If you have electrical questions consult your local electrical code for approved grounding methods.

1. Connect the black supply wire to the black fixture wire using a wire nut (CC).
2. Connect the white supply wire to the white fixture wire using a wire nut (CC).
3. Loop the supply ground wire around the ground screw on the mounting bracket (C) and tighten it in place.
4. Connect the fixture ground wire to the supply ground wire using a wire nut (CC).
5. Wrap all wire connections with electrical tape for a more secure connection.

3. Mounting the Fixture

1. Place the fixture body (A) onto the fixture screws (EE).
2. Secure the fixture body (A) into place by using the decorative nuts (AA).

4. Assembling the Fixture

NOTE: Do not exceed a 60 watt incandescent light bulb (or CFL or LED equivalent). For more information on the proper lighting to use, see www.HOMEDEPOT.CA/lightingfacts.

1. Secure the glass shades (B) to the socket cups using the socket rings (FF).
2. Screw a bulb (not included) into each socket on the fixture body (A).

Operation

1. Turn on power at the circuit breaker or fuse box.
2. Turn the light switch on to activate the fixture.

Care and Cleaning

NOTE: Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.

Exterior Maintenance

Use a dry or slightly dampened clean cloth and wipe the surface of the fixture.

Interior Maintenance

Disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box.

Use a dry or slightly dampened clean cloth to wipe the interior surface of the fixture.

Troubleshooting