HOMCOM 836-601V03 Assembly Instructions and User Manual

General Guidelines & Introduction

Important: Please read these instructions carefully before assembly and use. Retain this manual for future reference. If transferring ownership, include this manual.

This document provides general guidelines, notes, and warnings for the product. It may not cover every detail of all variations. For further assistance, please contact customer support.

Notes:

• Product is intended for indoor use only.
• Assemble and use strictly according to the manual.
• Seller assumes no liability for damage or injury from incorrect assembly or improper use.
• Keep away from fire sources and high temperatures.
• Assemble on a spacious, clean surface. Avoid placing unpacked items directly on the floor to prevent damage.
• Wear gloves [gloves emoji] during assembly/disassembly to avoid scratches from sharp edges.
• Match parts and fittings using part numbers.
• Periodically check and retighten screws for structural integrity.
• Wipe up spills immediately with a dry towel.
• Place the item on level, solid ground during use.

Warnings:

• Not suitable for children under 3 years of age. Adult supervision is required.
• Do not allow children to climb or play on the product to prevent tip-over injuries.
• Keep small parts and packaging (films, plastic bags, foam) away from children during assembly to prevent choking or suffocation hazards.

Parts List

The following parts are included:

• Part 1: Top Panel (1x)
• Part 2: Bottom Panel (1x)
• Part 3: Shelf Panel (1x) - Dimensions: 600x240x15mm
• Part 4: Side Panel (2x) - Dimensions: 770x239x15mm
• Part 5: Side Panel (2x) - Dimensions: 770x239x15mm
• Part 6: Back Support/Divider (2x) - Dimensions: 568x60x15mm
• Part 7: Shelf Panel (4x) - Dimensions: 566x217x15mm
• Part 8: Back Panel (8x) - Dimensions: 194.5x578x3mm

Hardware List

The following hardware is included:

• A1: Screw (M8*30) - 8x
• A2: Cam Lock - 16x
• B: Dowel (M8*50) - 4x
• C: Dowel - 2x
• D: Screw (M5*50) - 8x
• E: Shelf Support - 16x
• F: Corner Brace/Bracket - 16x
• G: Wall Strap/Bracket - 2x
• H: Small Screw/Nail - 6x
• I: Allen Key - 1x
• J: Screw - 6x
• K: Cam Dowel - 8x
• L: Screw (M3.5*14) - 16x

Assembly Instructions

Follow these steps carefully for assembly. Note that some steps are shown for two identical units or sections (indicated by X2), requiring repetition of the process.

Step 1: Prepare Panels

Insert 8x screws (A1) into the designated holes on panels 1 and 3.

Insert 8x screws (A1) into the designated holes on panels 4 and 5. Repeat this process for the second unit/section.

Step 2: Assemble Side Panels

For one unit: Insert cam dowels (K) into panels 4. Insert cam locks (A2) into panels 5, ensuring the arrow points towards the edge. Connect panels 4 and 5, then tighten the cam locks (A2) by turning them clockwise [clockwise-arrow]. (Uses 8x A2, 8x K)

Repeat this step for the second unit/section.

Step 3: Connect Base and Shelves

For one unit: Insert 2x dowels (C) into panel 3. Attach panel 3 to the side panels (4) using 4x screws (D).

Attach the remaining side panels (5) to the structure using 4x cam dowels (K) and 4x cam locks (A2), ensuring correct orientation and tightening.

Step 4: Insert Shelves

For one unit: Slide the 4x back panels (8) into the grooves on the side panels (4 and 5).

Insert 16x shelf supports (E) into the pre-drilled holes on the side panels (4 and 5) at the desired shelf heights. Place the 4x shelf panels (7) onto the supports.

Step 5: Attach Bottom and Top Panels

For one unit: Attach the bottom panel (2) to the assembled structure using 4x cam dowels (K) and 4x cam locks (A2).

Secure the structure with 4x dowels (B) and 4x screws (D).

Attach the top panel (1) similarly using 4x cam dowels (K) and 4x cam locks (A2).

Step 6: Secure Back Panels

For one unit: Attach the back panels (8) to the rear of the unit using 6x screws (J) and 16x screws (L). Ensure the panels are flush with the edges.

Attach 16x corner braces/brackets (F) to the back corners using 16x screws (L).

Step 7: Final Securing

For each unit: Secure the unit to the wall using the provided 2x wall straps (G) and appropriate wall fixings (not included). Follow the instructions for attaching the straps to the unit and the wall. This is crucial to prevent tip-over accidents.

Important Safety Information: Furniture Tip-Over Prevention

WARNING: Serious or fatal crushing injuries can occur from furniture tip-over.

To reduce the risk of furniture tip-over:

• ALWAYS install the tip-over restraint provided.
• NEVER allow children to stand, climb, or hang on drawers, doors, or shelves.
• NEVER open more than one drawer at a time.
• Place heaviest items in the lowest drawers.

Contact Information

For questions or assistance, please contact the relevant customer care center:

• US: 001-877-644-9366, customerservice@aosom.com
• CA: 416-792-6088, customerservice@aosom.ca
• FR: 0033-1-84166106, aosom@mhfrance.fr
• DE: +49 40 87408465, service@aosom.de
• ES: 0034-931294512, atencioncliente@aosom.es
• PT: 0034-931294512, info@aosom.pt
• UK: 0044-800-240-4004, enquiries@mhstar.co.uk
• IT: 0039-0249471447, clienti@aosom.it