Introduction and General Guidelines
Please read the following instructions carefully and use the product accordingly. Keep this manual and hand it over when you transfer the product. This summary may not include every detail of all variations and considered steps. Please contact us when further information and help are needed.
The product is intended for indoor use only. It must be assembled and used in accordance with the provisions of this manual. Personal injury and/or damage to the product may occur if the product is used outside of its intended purposes and/or if it has been changed/modified from its original design. The seller does not assume any responsibility or liability with respect to any injury/damage caused by incorrect assembly or improper use.
Keep the product away from fire sources and high temperatures.
Please assemble the item on a spacious surface and do not place the unwrapped product directly on the ground to avoid product damage.
Please wear gloves during the assembly and/or disassembly process to avoid scratches from any sharp edges.
Please match the corresponding part and fitting based on the part number in the manual.
Periodically inspect screw tightness while the product is in use. If necessary, retighten to ensure structural integrity.
If you accidentally spill water or another liquid on the surface, immediately wipe clean with a dry towel.
Please place this item on level, solid ground during use.
Safety Warnings
⚠️ It is not intended for use by children under 3 years of age. Children must be under adult supervision to use the product.
Children should not climb or play on the product in order to avoid tipping over the furniture and causing serious injury.
During assembly, keep all small parts out of the reach of children. Small parts may be fatal if swallowed or inhaled.
To avoid the potential dangers of suffocation, please keep all parts and packaging (film, plastic bags, foam, etc.) away from babies and children.
Assembly Hardware Explanation
Quickfit: Tighten the quickfit fastener until its shoulder is flush with the panel. Do not overtighten or undertighten.
Cam Lock: When fitting the cam lock, ensure the starting position is correct before inserting the connecting quickfit. The head of the quickfit should be in the centre of the cam lock when the two panels are joined. Turn the cam lock clockwise ↻ to tighten.
Parts List
- Part 1: Top/Bottom Panel (580x190x15mm)
- Part 2: Top/Bottom Panel (580x240x15mm)
- Part 3: Side Panel (502x170x15mm)
- Part 4: Side Panel (600x169x15mm)
- Part 5: Side Panel (600x169x15mm)
- Part 6: Shelf (468x151x12mm) - Quantity: 6
- Part 7: Back Panel (304.5x480x3mm) - Quantity: 4
Hardware List
- A1 (Cam Bolt): x8
- A2 (Cam Lock): x4
- B (Dowel): x4
- C (Screw M8*30): x2
- D (Screw M8*50): x4
- E (Shelf Support Peg): x24
- F (Screw M3.5*14): x16
- G (Wall Anchor Strap): x2
- H (Screw M5*50): x8
- I (Allen Key): x1
- J (Screw): x2
- K (Cam Lock): x12
- L (Screw): x16
Assembly Steps
- Step 1: Insert 8 x Cam Bolts (A1) into the pre-drilled holes on panels 1 and 3.
- Step 2: Attach side panels (4 and 5) to panel 3. Use 2 x Screws (C) and 4 x Screws (D).
- Step 3: Connect side panels (4 and 5) to panel 3. Insert 4 x Cam Locks (A2) and 4 x Cam Locks (K) into the corresponding holes. Ensure the Cam Lock heads align with the Cam Bolts. Turn Cam Locks clockwise ↻ to secure.
- Step 4: Slide the 4 x Back Panels (7) into the grooves on the assembled frame.
- Step 5: Attach the top panel (1) and bottom panel (2) to the side panels (4 and 5). Use 4 x Cam Locks (A2), 4 x Cam Locks (K), 4 x Dowels (B), and 4 x Screws (D).
- Step 6: Secure the bottom panel (2) to the side panels (4) using 8 x Screws (H).
- Step 7: Insert 24 x Shelf Support Pegs (E) into the desired pre-drilled holes on the inner sides of panels 4 and 5. Place the 6 x Shelves (6) onto the pegs.
- Step 8: Secure the back panels (7) to the unit. Use 2 x Screws (J), 16 x Screws (L), and 16 x Screws (F).
- Step 9: For safety, secure the unit to the wall using the provided 2 x Wall Anchor Straps (G) and appropriate wall fixings (not included). Follow the instructions for wall mounting.
Important Tip-Over Warning
⚠️ Serious or fatal crushing injuries can occur from furniture tip-over.
To reduce the risk of furniture tip-over:
- ALWAYS install the tip-over restraint provided.
- NEVER allow children to stand, climb, or hang on drawers, doors, or shelves.
- NEVER open more than one drawer at a time.
- Place heaviest items in the lowest drawers.
Contact Information
If you have any questions or need assistance, please contact the relevant customer care center:
United States (US)
Aosom LLC
Phone: 001-877-644-9366
Email: customerservice@aosom.com
Address: 27150 SW Kinsman Rd, Wilsonville, OR 97070 USA
Imported by: Aosom LLC
Made in China
Canada (CA)
Aosom Canada Inc.
Phone: 416-792-6088
Email: customerservice@aosom.ca
Address: 7270 Woodbine Avenue, Unit 307, Markham, Ontario Canada L3R 4B9
Imported by: Aosom Canada Inc.
Made in China
Germany (DE)
MH Handel GmbH
Phone: +49 40 87408465
Email: service@aosom.de
Address: Wendenstraße 309, D-20537 Hamburg, Germany
Manufacturer/Representative: MH Handel GmbH
Made in China
Italy (IT)
AOSOM Italy srl
Phone: 0039-0249471447
Email: clienti@aosom.it
Address: Centro Direzionale Milanofiori, Strada 1 Palazzo F1, 20057 Assago (MI)
Manufacturer/Representative: AOSOM Italy srl
Made in China
Spain (ES)
SPANISH AOSOM, S.L.
Phone: 0034-931294512
Email: atencioncliente@aosom.es
Address: C/ROC GROS,N°15.08550, ELS HOSTALETS DE BALENYÀ, SPAIN.
Manufacturer/Representative: SPANISH AOSOM, S.L.
Made in China
United Kingdom (UK)
MH STAR UK LTD
Phone: 0044-800-240-4004
Email: enquiries@mhstar.co.uk
Address: Unit 27, Perivale Park, Horsenden lane South, Perivale, UB6 7RH
Manufacturer/Representative: MH STAR UK LTD
Made in China
France (FR)
MH FRANCE
Phone: 0033-1-84166106
Email: aosom@mhfrance.fr
Address: 2 Rue Maurice Hartmann, 92130 Issy Les Moulineaux, France
Manufacturer/Representative: MH FRANCE
Made in China
For recycling information, visit www.queffairemesdechets.fr.
