JLab Bluetooth Earbuds User Manual

Your Warranty

All warranty claims are subject to approval by JLab Audio and are at JLab's sole discretion. Keep your proof of purchase to claim warranty service.

Contact Us

Email: support@jlabaudio.com

Visit: intl.jlabaudio.com/contact

Register Today

intl.jlabaudio.com/register

Product news | Useful tips | FAQs and more

Before First Use: Bluetooth Connection

1. Activate Bluetooth in your device settings. [Bluetooth Icon ?]

   [Diagram: Smartphone showing Bluetooth enabled]

2. Press and hold for over 10 seconds. Release. The LED blinks red and blue [??] to indicate pairing mode.

   [Diagram: Earbuds with button pressed, showing red/blue LED]

3. In your device's Bluetooth settings, select "JLab BT" to establish a connection. The LED blinks slow blue [?] once the Bluetooth connection is established.

   [Diagram: Smartphone connecting to "JLab BT", showing slow blue LED]

Returning Use

Once the JLab BT has been paired with your device, it will automatically connect to your Bluetooth device the next time it is turned ON. (Follow instructions under BUTTON FUNCTIONS)

Button Functions

• Volume Up: Tap once. [⬆️]
• Next Track: Press and hold for over 2 seconds. [▶️▶️]
• Power On: Press and hold for 3 seconds. [?]
• Power Off: Press and hold for 5 seconds. [?]
• Play/Pause / Answer/End Call: Tap once. [▶️/⏸️]
• Activate Siri (iOS) or "OK Google" (Android): Tap twice. [?]
• Bluetooth Connection: Follow the "Before First Use: Bluetooth Connection" steps.
• Volume Down: Tap once. [⬇️]
• Previous Track: Press and hold for over 2 seconds. [◀️◀️]

Equalizer Modes

Quickly tap both buttons to access different EQ settings (JLab BT has three EQ settings).

• JLab Signature: [Single Beep Icon ?] JLab C3™ Signature sound with enhanced vocals and bass.
• Balanced: [Two Beeps Icon ??] Even sound without additional amplification.
• Bass Boost: [Three Beeps Icon ???] Enhanced bass and sub-bass.

Voice and Tone Prompts

• Power On: Tone sound.
• Connected via Bluetooth: Two beeps.
• Battery Low: "Low Battery" (Less than 20%).
• Power Off: Tone sound.

Charging

1. Open the USB flap and connect the cable to a computer or USB power source to charge the device. Ensure your power source is 5V or less. [USB Icon ?]

   [Diagram: Earbuds charging via USB cable connected to computer/adapter]

2. The LED lights solid red [?] during charging. It lights blue [?] when fully charged.

   [Diagram: LED indicator showing red and blue states]

Fitting

1. Insert the Cush Fin first, then the Gel ear tip. Note: Design and options may vary. [Earbud Icon ?]

   [Diagram: Cush Fin and Gel ear tip being inserted into earbud]

2. Rotate the Cush Fins to the desired position. [Rotation Icon ?]

   [Diagram: Rotating Cush Fin on earbud]

3. Try different ear tips and Cush Fins to ensure a secure and comfortable fit.

   [Diagram: Various ear tips and Cush Fins]

Using the Cable Clip

1. Attach the cable clip approximately in the middle of the cable. [Clip Icon ?]

   [Diagram: Cable clip attached to earbud cable]

2. Clip onto your shirt, either at the front or back. [Shirt Icon ?]

   [Diagram: Clip attached to shirt collar]

Troubleshooting Connection

JLab BT Not Appearing in My Device

1. Turn Bluetooth OFF and ON again in your device settings. [Bluetooth Icon ?] [Settings Icon ⚙️]

   [Diagram: Smartphone showing Bluetooth toggle]

2. If you still don't see the JLab BT, repeat the steps in "Before First Use: Bluetooth Connection".

   [Diagram: Smartphone Bluetooth settings]

JLab BT Not Reconnecting After Power On

1. Forget the JLab BT in your device settings. [Forget Device Icon ❌]

   [Diagram: Smartphone showing forgotten Bluetooth device]

2. Turn Bluetooth OFF and ON again in your device settings. [Bluetooth Icon ?] [Settings Icon ⚙️]

   [Diagram: Smartphone showing Bluetooth toggle]

3. Repeat the steps in "Before First Use: Bluetooth Connection".

   [Diagram: Smartphone Bluetooth settings]

Troubleshooting Connection (Continued)

Bluetooth Connecting to Unwanted Device

Note: The JLab BT can store up to 8 devices. It will attempt to automatically connect to the last used device.

1. If you have more than one device connected to the JLab BT, DEACTIVATE Bluetooth on all unwanted devices and ACTIVATE it on the desired device. [Bluetooth Icon ?] [Block Icon ?]

   [Diagram: Smartphone showing multiple Bluetooth devices, then selecting one]

2. Press and hold for over 10 seconds. Release. The LED blinks red and blue [??] to indicate pairing mode. Select "JLab BT" in your device settings to establish a connection. The LED blinks slow blue [?] once the Bluetooth connection is established.

   [Diagram: Earbuds pairing process]

Warning

Ensure the USB flap is closed. This protects against sweat and water damage. [Water Drop Icon ?]

[Diagram: Earbuds with USB flap closed]

The JLab BT earbuds must be completely dry before charging. Moisture can damage internal components. It is recommended to air dry the device before charging. [Drying Icon ?️]

[Diagram: Water droplets near charging port, suggesting drying]

Caution

• Avoid getting moisture or liquids into the ear tips or charging port.
• Avoid extreme heat, cold, and moisture.
• Avoid dropping or crushing the earbuds, straining the cable with quick pulls or extreme force, or bending the cable at sharp angles.
• Earwax may accumulate in the ear tips, affecting sound quality. Carefully remove earwax with a cotton swab or other small tool to improve sound quality.
• If you experience discomfort or pain, try lowering the volume or temporarily discontinuing use.
• If you regularly experience discomfort while using this product, discontinue use and consult your doctor.
• It is recommended to treat your earbuds like a pair of sunglasses and store them in a safe place when not in use. [Sunglasses Icon ?️]