NITHO ELGAD - L GAMING DESK

IMPORTANT INFORMATION

READ CAREFULLY. KEEP THIS INFORMATION FOR FURTHER REFERENCE.

GENERAL GUIDELINES

• Please read the following instructions carefully and use the product accordingly.
• Please keep this manual and hand it over when you transfer the product.
• This summary may not include every detail of all variations and considered steps. Please contact NITHO for further information and help.

NOTES

• Please follow the assembly instructions precisely and only use the product as intended.
• If an odor is present when first opening the package, please leave the unwrapped product in a shaded and ventilated area for a few days to air out.
• Prior to assembly, please check the product for defects or missing accessories. If any defects are found or accessories are missing, do not use the product as damage or injury may occur. Please contact NITHO for assistance and replacement.
• During assembly, please only slightly tighten all screws in their correct position first, then fully tighten them. A Philips screwdriver is recommended but not included.
• It is suggested you regularly check the product's bolts and connections to ensure safe use.
• Assemble the item on a soft, flat, and clean surface to avoid scratches and damage.

WARNINGS

• During assembly, keep parts and packaging materials away from children and pets as they could cause injury and are a potential choking hazard.
• Avoid sharp objects or corrosive chemicals to prevent damage to the product.
• Please open the item slowly and cautiously to avoid pinching your hands by metal joints, especially children.

Components

Please check you have all the pieces listed below.

Part List

The desk supports up to 60KG.

Included Components (Hardware & Accessories)

• A: Power Cable x 1 pc
• B: Controller x 1 pc
• C: Leveling Studs x 4 pcs
• D: Wire Clips x 5 pcs
• E: 4mm Allen Key x 1 pc
• F: Screws M6X12 x 38pcs
• G: Screws M6X35 x 10 pcs
• H: Screws M5X8 x 14pcs
• I: Outlet Box x 2 pcs
• J: Hook x 2 pcs
• L: Hexagon bar x 1pcs
• M: Connector x 4 pcs
• N: Wooden Rod x 14 pcs
• O: Wire Basket x 1 pc
• P: Cup holder x 1 pcs
• Q: Wire Basket x 1 pc
• S: Lockable wheels x 4 pcs
• X: Earphone hook x 1 pcs
• Shim x 2pcs
• Screws M6X20 x 2 pcs

Assembly Instructions

Step 1: Prepare Desktop

Insert the wooden rods (N) into the designated openings on the desktop sections.

Diagram shows the underside of the desktop with numbered sections and indicates where wooden rods (N) are inserted.

Step 2: Attach Connecting Plate

Close the desktop panels. Use the 4mm Allen Key (E) and M6x12 screws (F) to secure the connecting plate (M) to the panel. Attention: Screws cannot be tightened all at once.

Diagram shows the desktop underside with connecting plates (M) being attached using screws (F) and an Allen key (E). An arrow indicates screws should not be tightened all at once.

Step 3: Attach Legs and Support Beam

Attach the legs (5, 6) and one support beam (7) to the desktop underside, ensuring the holes on the legs face the ground. Use the 4mm Allen Key (E) and M5x8 screws (H).

Diagram shows the legs (5, 6) and a support beam (7) being attached to the desktop underside, highlighting that holes should face the ground.

Step 4: Install Second Support Beam

Install the second support beam (7) on the other side in the same way as in Step 3.

Diagram shows the second support beam (7) being attached in the same manner as Step 3.

Step 5: Attach Bases and Sync Rod

Attach the bases (9) to the leg assemblies. Ensure the leveling studs (C) are on the same horizontal plane; if not, adjust them by hand. Connect the sync rod (10) between the leg mechanisms. Use the 4mm Allen Key (E) and M6x35 screws (G).

Diagram shows the bases (9) being attached to the legs and the sync rod (10) connecting the two leg mechanisms. Leveling studs (C) are shown being screwed into the bases.

Step 6: Install Side Brackets and Hooks

Stand the desk upright. Install the side brackets (8) and hooks. Hooks can be installed together with the brackets in any of the four holes according to personal habits. Use the 4mm Allen Key (E) and M5x8 screws (H).

Diagram shows the desk standing upright. Side brackets (8) and hooks are being attached to the legs using screws (H) and an Allen key (E). An inset shows a close-up of attaching a bracket and hook.

Step 7: Secure Table Frame

Assemble and secure the table frame together using the 4mm Allen Key (E) and M6x12 screws (F).

Diagram shows the frame of the desk being assembled and secured with screws (F) and an Allen key (E).

Step 8: Attach Accessories

Secure the controller (B), cable tray (Q), cup holder (P), and headphone stand (S) to the desktop. Use the provided screws and connectors.

Diagram shows the underside of the desktop with the controller (B), cable tray (Q), cup holder (P), and headphone stand (S) being attached using various screws and connectors.

Step 9: Install Cup Holder

Install the cup holder (P) using the 4mm Allen Key (E) and screws (Q, X).

Diagram shows a close-up of attaching the cup holder (P) using screws (Q, X) and an Allen key (E). A 360-degree rotation icon is shown.

Step 10: Connect Controller and Cables

Connect the Controller (B), AC Adapter, and Power Cable (A) to the Left Leg assembly.

Diagram shows the connection of the power cable (A) and controller (B) to a leg mechanism.

Step 11: Tidy Up Wires

Use Wire Clips (D) to tidy up the wires. An arrow indicates the direction of wire management.

Diagram shows the desk with wires being tidied using wire clips (D).

Controller Instruction

The controller features buttons for height adjustment and memory presets.

Controller Layout

The controller displays a height value (e.g., 69) and has numbered buttons (1, 2, 3, 4) for memory presets, along with up/down adjustment buttons.

RESET Setting

Method 1: Press and hold the "A" and "V" buttons on the controller simultaneously for several seconds until a beep is heard. Release the buttons. The desk will move automatically until it shows '69', indicating the reset is successful.

Height Adjustment

Use the "Up" button (typically labeled 'A') to raise the desk and the "Down" button (typically labeled 'V') to lower it.

Switch Display (cm/inch)

Press and hold the "V" button and Button 4 simultaneously to switch between centimeters (cm) and inches (inch) display.

Memory Height

To store a height: Press and hold any memory button (1, 2, 3, or 4). The display will flash twice. Release the button to save the current height. To recall a stored height: Press the memory position button (1, 2, 3, or 4), and the desk will automatically adjust to that saved height. This standing table has four memory height positions. The stored memory remains valid after the power is turned off. You can use the upper and down buttons to adjust the standing table to your preferred working height.

Troubleshooting Guide

• If your standing desk does not work properly, you may need to reset it.
• If any error codes appear, you need to reset it.
• If it still does not work after the reset, please contact NITHO for more help.

Maintenance and Consideration

1. During daily maintenance, use a clean soft cloth to remove surface dust. Do not use a wet cloth or hard material to wipe the surface of the table.
2. Avoid contacting the surface with acid-based chemicals.
3. For slight scratches, gently wipe with a soft cloth; this can smooth out scratches. Avoid attaching tape directly to the outer surface of the metal feet to prevent paint from peeling.

Single Motor Standing Desk Fault Codes and Troubleshooting Methods

Fault Codes:

• E01: Under-voltage protection
• E02: Over-voltage protection
• E03: Over-current protection
• E04: Overload protection
• E05: Motor 1 Hall sensor not detected
• E09: Controller is not connected to the control box; the controller needs a replacement.
• E13: Imbalance or obstruction

Troubleshooting Steps:

• When E05 appears: Check if the motor wires are connected to the control box. Power off and wait for the screen to turn off before powering on again. If E05 still appears, replace the control box or motor.
• When E13 appears: This can be resolved by manually raising and lowering the desk several times.
• When E01, E02, E03, or E04 appears: Unplug the power and wait for the hand controller display to turn off, then power on again. If E01 or E02, E03, E04 codes still appear after pressing the up or down buttons without turning off the power, disconnect the male and female connectors connecting the motor and control box, then press the up or down button. If the code changes from E01/E02/E03/E04 to E05, it indicates a motor problem and requires replacement. If the code remains unchanged, it indicates a control box problem and requires replacement.
• If the controller screen does not light up after powering on: Check for wiring issues and loose connections. If the wiring is correct, unplug the power plug for about ten seconds and then power it on again. If you hear a "beep" sound from the control box but the hand controller screen remains unlit, replace the hand controller. If there is no "beep" sound from the control box, replace the control box.

SERVICE & SUPPORT

If you have any questions or require support, contact the NITHO Team at support@nitho.com or visit our website www.nitho.com.

NITHO GmbH - Victoriastrasse 3b - 86150 Augsburg - Germany

✉ support@nitho.com | ? www.nitho.com | ? NITHOGAMES | ⓕ NITHOGAMES