Product Features
- PerformanceSpout: Eco-friendly 1.2 GPM and WaterSense certified spout conserves water without sacrificing performance.
- EternalSeal™: High-quality ceramic disc cartridge continually prevents leaks and drips for flawless water flow.
- DIY Installation: User-friendly installation guide supports a seamless, three-hole installation.
- Single Handle Lever: One lever effortlessly controls water pressure and temperature.
- Easy to Clean: High-quality, spot-resistant finish is easy to wipe clean.
- FinishPlated: 7-layer coated finish ensures consistent hardware finish throughout the product.
Certifications & Warranty
Certified by IAPMO R&T: CUPC, NSF-61, NSF 372, AB1953, CEC, and WaterSense.
VIGO Bathroom Faucets have a Limited Lifetime Warranty.
Packing List
- Faucet
- Supply Lines
- Plumber's Tape
Tools Required
- Adjustable Wrench
- Eye Protection
- Safety Gloves
- Plumber's Putty (Optional)
- Pipe Tape
- Flat Screwdrivers
Product Registration
To activate your warranty, please register your product at vigoindustries.com/register.
Activate Now!
Dimensions
Diagrams illustrating the faucet's dimensions are provided. The front view shows the overall height, spout reach, and spout height. The top view shows the faucet's width and handle placement. A table details the specific measurements:
| Measurement | Value |
|---|---|
| Faucet height | 6 3/8" (163mm) |
| Spout reach | 5 1/4" (133mm) |
| Spout height | 4 3/8" (112mm) |
| Hole Diameter | Ø1 3/8" (31.5mm) |
| Water supply connection | 3/8" |
Parts List
An exploded view diagram shows the faucet assembly components. The parts are listed below:
- 1: Handle assembly (68119)
- 2: Handle escutcheon (68120)
- 3: Cartridge nut (68040)
- 4: Cartridge (64027)
- 5: Supply hoses (74020)
- 6: Aerator (64031)
- 7: Mounting hardware (68129)
Installation Steps
Installation must be performed by a qualified licensed plumber.
Step 1.1: Preparation
Follow these preparation steps:
- 1.1.1 Shut off water supply.
- 1.1.2 Remove the old faucet and flexible hoses.
- 1.1.3 Clean the sink surface in preparation for the new faucet.
- 1.1.4 Flush the water connection at home to ensure no debris is present in the line.
Diagram Description: Shows water shut-off valves and the process of removing old hoses.
Step 1.2: Connect Hoses
Connect the water supply hoses:
- 1.2.1 Apply plumber's tape to the threads of the water supply pipes.
- 1.2.2 Connect the flexible hoses to the brass pipes.
Diagram Description: Illustrates applying tape to threads and connecting flexible hoses to the faucet's brass pipes.
Step 1.3: Install New Faucet
Install the faucet onto the countertop:
- 1.3.1 Place the new faucet in its position on the countertop.
- 1.3.2 From under the countertop, place the rubber washer, metal ring, and brass nut onto the threaded pin of the faucet.
- 1.3.3 Tighten the nut to secure the faucet.
Diagram Description: Shows the faucet being placed, followed by the installation of the rubber washer, metal ring, and nut from underneath the countertop, and finally tightening the nut.
Step 1.4: Open Water Lines
Open the water supply lines:
- 1.4.1 Wrap tape on the cold and hot water pipe threads.
- 1.4.2 Place the supply hoses onto the respective threads.
- 1.4.3 Screw the hoses onto the cold and hot water threads.
- 1.4.4 Open the cold and hot water lines to check for leaks.
Diagram Description: Depicts connecting supply hoses to the water lines and opening the shut-off valves.
Safety Tips and Warnings
Safety First:
- Installation must be performed by a qualified licensed plumber.
- Read all instructions thoroughly before installation.
- Confirm all parts are included and visually inspect the unit for any defects before proceeding.
- Contact VIGO Technical Support if you have any questions prior to installation.
- If soldering is used during installation, remove seats, cartridges, and washers before applying flame. Damage from improper soldering will void the warranty.
- Always protect your eyes with safety glasses when cutting or soldering water supply lines.
⚠️ WARNING: California Proposition 65
This product can expose you to lead, a chemical known to the State of California to cause cancer and reproductive harm. For more information, visit: www.P65Warnings.ca.gov
Contact & Support
For installation help, missing or replacement parts, please contact VIGO Product Support:
- Phone: 1-866-591-7792 (Option 2)
- Hours: Monday - Friday, 9:30 am - 5:30 pm EST
- Email: sf@vigoindustries.com
- Website: vigoindustries.com
