STOCKHOLM TV Unit

Important Safety Information

WARNING: Serious or fatal crushing injuries can occur from furniture tip over. To prevent tip over, this furniture must be used with the wall attachment device(s) provided.

Screws and plugs for the wall are not included. Use screws and plugs suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instruction carefully.

This safety warning is provided in multiple languages for your convenience.

Tools Required

The following tools are depicted as necessary for assembly:

• Screwdriver (Phillips head)
• Spirit Level
• Electric Drill (for wall mounting, if applicable)
• Screwdriver (another type)

Parts List

Assembly Instructions

Step 1

Attach the side panels to the main base panel. The diagram shows two side panels being inserted into slots on the base panel. Arrows indicate the direction of insertion. A close-up shows the correct alignment of the panels.

Step 2

Secure the side panels to the base panel using cam lock mechanisms. Insert cam lock screws into the base panel and then insert cam locks into the side panels. Turn the cam locks [?] to secure the connection. Detail views show the correct [✔️] and incorrect [❌] methods.

Step 3

Attach the central vertical dividers to the base panel. The diagram shows three vertical dividers being positioned and inserted into slots on the base panel. Arrows indicate the direction of insertion.

Step 4

Secure the central vertical dividers using cam lock mechanisms. Insert cam lock screws into the base panel and then insert cam locks into the dividers. Turn the cam locks [?] to secure the connection. Detail views show the correct [✔️] and incorrect [❌] methods.

Step 5

Attach the back panel. The diagram shows a large, thin back panel being slid into grooves on the rear of the assembled frame. Arrows indicate the sliding motion.

Step 6

Prepare the shelves for installation. For each of the three shelves, attach two shelf support brackets (117346) to the underside of the shelf using screws (108444). A close-up shows the bracket being attached with 6x screws.

Step 7

Insert the shelves into the unit. Slide the shelves into place. The shelf support brackets (117346) engage with the unit's internal supports, indicated by a 'CLICK!' sound, signifying a secure lock.

Step 8

Prepare the top panel for attachment. Insert 8x dowels (101350) into the pre-drilled holes on the underside of the top panel.

Step 9

Attach the top panel to the main unit. Position the top panel onto the assembled body. Secure it using the bracket (100001) and 6x screws (100214).

Step 10

Assemble the leg frames. Construct two leg frames by connecting horizontal support pieces to vertical leg pieces using dowels and screws. Detail views show correct [✔️] and incorrect [❌] alignment of parts.

Step 11

Continue assembling the leg frames. Further connect parts for the leg structure, similar to Step 10, with detail views illustrating the correct assembly process.

Step 12

Attach the assembled leg frames to the main unit. With the main unit upside down, position the leg frames and secure them with 2x dowels (101350) per leg frame.

Step 13

Flip the unit upright and attach the leg frames. Turn the unit over. Then, attach the leg frames to the underside of the main unit using screws. A close-up shows the screw insertion into the leg frame and the main unit.

Step 14

Secure the leg frames to the main unit. Use the bracket (100001) and 6x screws (105016) to further secure the leg frames to the main body.

Step 15

Attach adjustable feet to the leg frames. Screw 4x adjustable feet (102728) into the bottom of the leg frames. The diagram shows rotation [?] to adjust the feet. Arrows indicate vertical adjustment [↕️].

Step 16

Install cable grommets. Insert 6x cable grommets (115982) into the pre-cut holes on the top surface of the unit.

Step 17

Level the unit using the adjustable feet. Place a spirit level on the top surface. Rotate the adjustable feet (102728) to ensure the unit is level. Arrows indicate vertical adjustment [↕️].

Step 18

Prepare for door installation. A warning symbol [⚠️] is shown next to a drawer-like structure, indicating caution. Another diagram shows a person struggling with a tip-over scenario [❌ person falling over furniture], reinforcing the wall-mounting warning.

Drill pilot holes for hinges and attach hinge components (117346) to the inside of the unit using screws.

Step 19

Attach hinges to the doors. Attach hinge components (115982) to the doors using screws. A close-up shows the correct attachment of the hinge part to the door.

Step 20

Attach the doors to the unit. Hang the doors onto the unit. Use hinge components (121762) to connect the doors to the unit's frame. 6x hinge components are used.

Step 21

Install internal shelves. Insert shelves into the unit. Arrows indicate insertion. A warning symbol [❌] is shown next to an incorrect method of inserting a shelf, indicating it should not be forced or angled incorrectly.

Step 22

Secure the internal shelves. Place a shelf and secure it from underneath using a bracket (121762). An arrow indicates the downward motion for securing.

Step 23

Continue securing internal shelves. Secure another shelf using 2x brackets (121762).

Step 24

Final shelf placement. Place and secure the last shelf using the indicated method.

Step 25

Install drawer slides. Attach drawer slide components (146868 and 146870) to the unit and the drawer boxes. This involves attaching slide components to the unit's internal structure using screws (108444) and then attaching corresponding slide parts to the drawers. Detail views show the attachment and a 'CLICK!' sound indicating successful engagement.

Information

The 'i' icon throughout the manual indicates important information or tips.

The 'STOP' icon indicates a critical warning.