GZDX-V1 Shoe Storage Bench Assembly Instructions
Model: FTLFSS-6009
Notice:
- Follow the installation instructions carefully. Please confirm all accessories are present before installation.
- Do not fully tighten screws during initial assembly. Fully tighten screws only once all pieces are correctly assembled.
- If you encounter any problems during installation, please contact customer service.
The following diagram shows the assembled shoe storage bench.
Parts List:
| Part | Description | Quantity |
| 1 | Top Panel | x1 |
| 2 | Left Side Panel | x1 |
| 3 | Right Side Panel | x3 |
| 4 | Back Panel (Upper) | x1 |
| 5 | Back Panel (Lower) | x1 |
| 6 | Shelf | x3 |
| 7 | Shelf | x9 |
| 8 | Drawer Front Panel | x3 |
| 9 | Drawer Side Panel | x2 |
| 10 | Bottom Panel | x1 |
| 11 | Support Panel | x1 |
| 12 | Drawer Bottom Panel | x4 |
| 13 | Drawer Back Panel | x1 |
| 14 | Drawer Base | x1 |
| 15 | Legs | x4 |
Hardware List:
| Identifier | Image Description | Quantity |
| (A) | Cam Lock | x6 |
| (B) | Screw (M7*50) | x34 |
| (C) | Screw (M8*30) | x4 |
| (K) | Dowel | x6 |
| (P) | Screw (M3.5*12) | x30 |
| (Q) | Screw (M3.5*14) | x18 |
| (S) | Screw (M4*16) | x6 |
| (T) | Washer | x6 |
| (U) | Cam Bolt | x6 |
| (V) | Cam Bolt | x6 |
| (Y) | Foot Pad | x4 |
| (Z) | Anti-tip Hardware | x2 Sets |
Step 1
Attach cam bolts (U, V) to side panels (2, 5). Insert cam locks (A) into the corresponding holes on the top panel (1) and bottom panel (10). Connect side panels to the top and bottom panels using the cam bolts and locks. Insert dowels (K) into the designated holes.
Diagram shows side panels (2, 5) with cam bolts (U, V) being inserted. Top panel (1) and bottom panel (10) have cam locks (A) inserted. The panels are then joined.
Step 2
Attach the back panels (4, 5) to the assembled frame using screws (B). Insert shelves (6) into the pre-drilled holes.
Diagram shows back panels (4, 5) being attached with screws (B). Shelves (6) are shown being inserted into the frame.
Step 3
Attach the legs (15) to the bottom panel (10) using screws (C). Insert foot pads (Y) into the bottom of the legs.
Diagram shows legs (15) being attached to the bottom panel (10) with screws (C). Foot pads (Y) are shown being attached to the legs.
Step 4
Attach the support panel (11) to the side of the unit using screws (B). Attach the drawer bottom panels (12) and drawer back panel (13) to the drawer front panel (8) using screws (A) and (B).
Diagram shows support panel (11) being attached with screws (B). Drawer components (8, 12, 13) are shown being assembled with screws (A, B).
Step 5
Insert drawer slides (9) into the main unit using screws (B). Attach the assembled drawer boxes to the slides.
Diagram shows drawer slides (9) being attached to the main unit with screws (B). The drawer boxes are then shown being connected to the slides.
Step 6
Attach the drawer base (14) to the assembled drawer unit using screws (A) and (B).
Diagram shows drawer base (14) being attached to the drawer unit with screws (A, B).
Step 7
Assemble the flip-out shoe compartments. Attach side panels (L, J) to the base using screws (P). Attach the back panels using screws (P).
Diagram shows the assembly of the flip-out shoe compartments. Panels (L, J) are attached to a base with screws (P), and back panels are also attached with screws (P).
Step 8
Continue assembling the shoe compartments using screws (P).
Diagram shows further assembly of the shoe compartments using screws (P).
Step 9
Attach the drawer runners (8) to the shoe compartment frames using screws (Q). Ensure correct orientation.
Diagram shows drawer runners (8) being attached to the shoe compartment frames with screws (Q).
Step 10
Attach the drawer fronts to the assembled shoe compartments. Adjust the clearance of the two boards as needed using screws (P) and shelf (7).
Diagram shows drawer fronts being attached. Adjustment of board clearance is indicated with screws (P) and shelf (7).
Step 11
Attach the support brackets (K) to the shoe compartments using screws (S) and dowels (K).
Diagram shows support brackets (K) being attached to the shoe compartments with screws (S) and dowels (K).
Step 12
Attach the handles (T) to the drawer fronts using screws (P).
Diagram shows handles (T) being attached to the drawer fronts with screws (P).
Step 13
Insert the assembled drawer bases (14) into the shoe compartments.
Diagram shows the insertion of the drawer bases (14) into the shoe compartments.
Step 14: Anti-Tip Safety
Attention: For safety and stability, it is recommended to secure the anti-tip accessories to the wall to prevent tipping, injury, and property damage.
Diagram shows the anti-tip hardware (Z) being attached to the top of the unit and then to a wall for stability.
