STEP 1
Attach part 2 to the side of part 1 using twenty (20) screws D (3.5x12).
Important Notices
1. Follow the installation instructions carefully. Please confirm all accessories are present before installation. 2. Do not fully tighten the screws during initial assembly. Fully tighten screws only after all pieces are correctly assembled. 3. If you encounter any problems during installation, please contact YITAHOME customer service.
Parts List
Components
- Part 1 (x1)
- Part 2 (x1)
- Part 3 (x1)
- Part 4 (x1)
- Part 5 (x2)
- Part 6 (x2)
- Part 7 (x1)
- Part 8 (x1)
- Part 9 (x2)
- Part 10 (x1)
- Part 11 (x1)
- Part 12 (x1)
- Part 13 (x1)
- Part 14 (x4)
Hardware
- Screw A (5x40) (x18+1)
- Screw B (6x35) (x8+1)
- Cam Lock C (x2)
- Screw D (3.5x12) (x20+2)
- Screw E (3.5x12) (x12+1)
- Screw F (3.5x12) (x8+1)
- Cam Lock G (x2)
- Screw H (3.5x35) (x2+1)
- Screw I (3.0x12) (x10+1)
- Screw J (3.0x14) (x4)
- Screw K (3.5x12) (x8+1)
Tools
- Allen Wrench (3mm) (Part L)
- Allen Wrench (Part M)
Assembly Steps
STEP 2
Insert part 4 into the slots on part 5 (x2). Secure each part 4 with one (1) cam lock G, turning clockwise to lock.
STEP 3
Attach part 10 to the top edge of part 1 using one (1) screw A (5x40).
STEP 4
Attach part 3 to the opposite side of part 1 from part 2, using two (2) screws E (3.5x12).
STEP 5
Attach two (2) instances of part 4 to the sides of part 1. Secure each with one (1) screw B (6x35) and one (1) screw E (3.5x12). Ensure correct orientation as indicated.
STEP 6
Attach part 8 to the top edges of the two assembled part 4 units. Secure each with one (1) screw E (3.5x12). Ensure correct orientation.
STEP 7
Attach part 3 to the top of part 8 using four (4) screws A (5x40).
STEP 8
Attach two (2) instances of part 5 to the sides of part 1, below the previously attached parts. Secure each with two (2) screws F (3.5x12).
STEP 9
Attach two (2) instances of part 9 to the sides of part 10 and part 11 respectively. These appear to be drawer slides or supports.
STEP 10
Assemble the main cabinet structure. Attach part 2 to the front edges of parts 3 and 4 using two (2) screws B (6x35) and four (4) screws E (3.5x12). Then, attach two (2) instances of part 5 to the bottom edges of parts 3 and 4 using four (4) screws F (3.5x12).
STEP 11
Attach part 7 to the inner side of part 2 using four (4) screws A (5x40).
STEP 12
Attach part 7 to the inner side of part 2 using four (4) screws J (3.0x14).
STEP 13
Attach part 11 to the inner side of part 2 using four (4) screws B (6x35) and six (6) screws A (5x40).
STEP 14
Attach part 7 to the inner side of part 11 using two (2) connectors L.
STEP 15
Attach part 1 to the back of the assembled structure using eight (8) screws I (3.0x12).
STEP 16
Attach two (2) instances of part 6 to part 12. These boards can be adjusted up and down, serving as shelves.
STEP 17
Attach part 13 to part 12 using two (2) cam locks C. Turn clockwise to secure.
STEP 18
Attach part 13 to part 12 using two (2) screws H (3.5x35). Then, attach part 7 to the front edge of part 13 using two (2) screws H (3.5x35). Note 'Short side' and 'Long side' indicators for part I, suggesting orientation for shelf placement.
STEP 19
Attach two (2) instances of part 9 to part K (x8). These are likely drawer slide components.
STEP 20
Attach two (2) instances of part M to part 14. These are likely drawer handles or feet.
STEP 21
Installation Completed. Your YITAHOME DGHR-V1 shoe cabinet is now assembled.
