AECOJOY 14'x12' Attached Pergola Assembly Instructions SS16413

Introduction

Thank you for choosing our product. Please read the contents on the second page carefully.

Before starting the installation, please thoroughly check the listed accessories below and read this manual attentively. Then proceed with the assembly step by step. If you have any questions, please don't hesitate to contact us.

Attention

1. Thank you for trusting us. You are entitled to a one-year warranty and lifelong customer service, and we have marked detailed notes on the second page.

2. Our gazebo is packaged in 3 boxes. Box A and Box B contain all the frames, while Box C contains all the top panels.

3. We encourage you to reach out to us at the earliest if you encounter any issues.

4. We kindly request your attention to installation safety and child safety.

Important Information

To Every Customer Who Has Purchased Our Gazebos

Before you begin the installation, please take a few minutes to carefully read the following important notes and be aware of your rights and entitlements.

Some of Your Concerns:

1. Please note that if you find any damage to the package upon arrival, resulting in loss of internal components or visible damage, please contact us. AECOJOY will take responsibility for any damages caused during transportation.

2. Please ensure that you begin installation after receiving all accessories. If not, please contact AECOJOY to inquire about the corresponding package status, and we will respond within 24 hours.

3. Product stability has been tested: the product can withstand winds of approximately 40-60 mph and a static pressure test of 6.5 lbs per square foot after correct installation and fixation. (Snow accumulation of about 7 inches in thickness will not pose a threat to the product.)

4. If you have any questions regarding accessory defects, product use, or product installation, please feel free to contact AECOJOY. We have simple installation videos available for you.

Some Precautions:

1. Please use the tools provided by AECOJOY to secure the gazebo to the wall to ensure stability. *Please purchase matching ground stakes for securing the product to the ground according to the installation area you plan. If you are unsure about how to choose, please let us know.

2. Please tighten the screws after ensuring that all screw holes have been properly inserted to avoid uneven hole alignment.

3. Please use a ladder when installing the top part.

4. Keep children away during the installation process, as the product contains small parts that could be swallowed.

5. Do not choose to install the product in strong winds or severe weather conditions.

Your Rights And Benefits:

1. You are entitled to a one-year warranty on the product and lifelong 24/7 customer service from AECOJOY.

2. If you wish to connect multiple products together through DIY, please contact AECOJOY for advice on the connections or to seek the necessary accessories for your construction needs.

3. AECOJOY is pleased to introduce our brand-new adjustable and expandable support columns, designed to meet your utmost stability requirements. Feel free to get in touch with us if you're interested.

Parts List

Parts List-B

Parts List-A

Parts List-C

Assembly Steps

Step 1

Connect parts A (x2), B (x3), C (x5), and L (x5) using W1 (x40) bolts. The diagram shows how A, B, and C pieces are oriented and connected with L pieces using W1 bolts. A zoomed view shows the connection detail between A/B and C.

Step 2

Attach M (x12) parts to the assembled structure using W1 (x2) and Z1 (x10) bolts. The diagram shows attaching M brackets to vertical posts (likely A/C components) using W1 and Z1. A zoomed view shows the connection detail.

Step 3

Assemble horizontal beams. Connect D (x4), D1 (x2), N (x4), and U (x4) parts using W1 (x32) bolts. The diagram shows a long assembly of beams D, D1, N, and U, connected by W1 bolts. A zoomed view shows the connection detail using D/D1 and W1 bolts.

Step 4

Attach the assembled beams from Step 3 to the vertical posts. Connect parts A/B and D/D1 using Y (x20) bolts. The diagram shows two sets of vertical posts with horizontal beams attached. A zoomed view shows the connection of A/B to D/D1 using Y bolts.

Step 5

Attach O (x2) and P (x2) brackets to the structure using W1 (x17) and Z4 (x1) parts. The diagram shows attaching O and P brackets to the main frame. Zoomed views illustrate the connection points using W1 bolts and the Z4 Allen wrench.

Step 6

Assemble the roof support structure. Connect E1 (x16), E (x16), and T (x8) parts using S (x8), W3 (x48), U1 (x16), Z1 (x64), X1 (x16), and X2 (x32) bolts. The diagram shows a long assembly of E1, E, and T beams. Zoomed views show detailed connections using W3, Z1, U1, S, X1, and X2.

Step 7

Attach the roof support structure to the main frame. Connect E/E1 with H (x8) parts using Q (x16), W3 (x16), V (x16), W1 (x32) bolts. The diagram shows the roof structure being attached to the main pergola frame. Zoomed views show connections using Q, W3, V, and W1 bolts.

Step 8

Attach Q (x16) parts to the frame using W1 (x32) bolts. The diagram shows the final attachment of Q parts to the main frame. A zoomed view illustrates the connection. A tip explains the correct orientation of part Q for better support.

TIPS: Part Q is used by slotted holes. Please use the same sides of both holes to make the top side of Q higher than Part D. Slotted holes will support the cover board more strongly.

Step 9

Assemble the roof panels. Connect J (x2), V (x2), I1 (x1), and I (x2) parts using W1 (x8) bolts. The diagram shows the assembly of roof panel supports. Zoomed views show connections using J, V, I1, I, and W1 bolts.

Step 10

Attach the roof panels. Connect H (x8) and I (x8) parts using W4 (x8) bolts. The diagram shows the main pergola frame with horizontal beams (H) and additional supports (I) being attached using W4 bolts.

Step 11

Install the UV Protected Boards (K3). Place K3 (x7) boards onto the roof structure. The diagram shows the pergola with the main frame and roof supports, and then shows the K3 boards being placed on top.

Step 12

Secure the UV Protected Boards. Attach R (x8) and F (x7) parts using W1 (x8) bolts. The diagram shows the K3 boards being secured to the frame. Zoomed views show the attachment of R and F components using W1 bolts.

Step 13

Install G (x7) parts. The diagram shows the pergola with K3 boards installed. G parts are then attached to the frame. A zoomed view shows the attachment of G. A note explains that each side of G has a drainage hole and should be installed with the drainage hole facing upwards to prevent water leakage.

Note: Each side of the 'G' has a drainage hole. Make sure to install with the side containing the drainage hole facing upwards (the higher side) to prevent water leakage.

Step 14

Final placement of K3 (x14) boards and G (x7) parts. The diagram shows the pergola with K3 boards and G parts being finalized. A zoomed view shows the attachment of G.

Step 15

Secure the roof structure further. Attach R (x8) and F (x7) parts using W1 (x8) bolts. The diagram shows the final securing of the roof panels and frame. Zoomed views illustrate the connection points.

Step 16

Secure the pergola to the ground or wall. Use Z5 (x8) Expansion Bolts. The diagram shows a close-up of a connection point (likely a leg or base) and indicates the use of Z5 expansion bolts. Dimensions are provided: 164CM, 4CM, 380.3CM, 190.15CM, 230CM, 5CM. A zoomed view shows the Z5 bolt being used with part M.

Dimensions: Height: 164CM, Width: 380.3CM, Depth: 190.15CM. Other dimensions indicated: 4CM, 5CM, 230CM.