Assembly Instructions SS16410
20'X8' Attached Pergola
Thank you for choosing our product.
Please read the contents on the second page carefully.
- Before starting the installation, please thoroughly check the listed accessories below and read this manual attentively.
- Then proceed with the assembly step by step. If you have any questions, please don't hesitate to contact us.
A visual representation of the assembled pergola is provided.
Attention
- Thank you for trusting us. You are entitled to a one-year warranty and lifelong customer service. Detailed notes are provided on the second page.
- Our gazebo is packaged in 3 boxes. Box A and Box B contain all the frames, while Box C contains all the top panels.
- We encourage you to reach out to us at the earliest if you encounter any issues.
- We kindly request your attention to installation safety and child safety.
To Every Customer Who Has Purchased Our Gazebos
Before you begin the installation, please take a few minutes to carefully read the following important notes and be aware of your rights and entitlements.
Some of Your Concerns:
- Please note that if you find any damage to the package upon arrival, resulting in loss of internal components or visible damage, please contact us. We will take responsibility for any damages caused during transportation.
- Please ensure that you begin installation after receiving all accessories. If not, please contact us to inquire about the corresponding package status, and we will respond within 24 hours.
- Product stability has been tested: the product can withstand winds of approximately 40-60 mph and a static pressure test of 6.5 lbs per square foot after correct installation and fixation. (Snow accumulation of about 7 inches in thickness will not pose a threat to the product.)
- If you have any questions regarding accessory defects, product use, or product installation, please feel free to contact us. We have simple installation videos available for you.
Some Precautions:
- Please use the tools we provide to secure the gazebo to the wall to ensure stability.
- Please purchase matching ground stakes for securing the product to the ground according to the installation area you plan. If you are unsure about how to choose, please let us know.
- Please tighten the screws after ensuring that all screw holes have been properly inserted to avoid uneven hole alignment.
- Please use a ladder when installing the top part.
- Keep children away during the installation process, as the product contains small parts that could be swallowed.
- Do not choose to install the product in strong winds or severe weather conditions.
Your Rights And Benefits:
- You are entitled to a one-year warranty on the product and lifelong 24/7 customer service.
- If you wish to connect multiple products together through DIY, please contact us for advice on the connections or to seek the necessary accessories for your construction needs.
- We're thrilled to introduce our brand-new adjustable and expandable support columns, designed to meet your utmost stability requirements. Feel free to get in touch with us if you're interested.
Parts List-B
- A x1: Top Back Leg
- B x3: Top Front Leg
- C x6: Bottom Leg
- D4 x4: Bottom Leg
- G x10: Middle Board Connection
- H x7: Arm Connection
- I2 x1: Arm Hold Tube (Short)
- J x4: Arm Hold Tube Connection
- L x6: Arm Hold Tube Connection
- M x14: Wall & Floor Connection
- N x4: Arm & Beam Connection
- N1 x2: Arm Protection
- O x2: Right Beam Hold
- P x2: Left Beam Hold
- Q x22: Arm & Beam Connection
- R x22: Arm Protection
- S x11: Arm Up Connection
- T x11: Arm Down Connection
- U x4: Beam Plug
- V x24: Hold Plug
- W1 x236: Bolt M6*15mm
- W2 x12: Bolt M6*70mm
- W4 x33: Bolt M6*35mm
- W5 x44: Bolt M6*40mm
- X1 x12: Bolt M6*15mm
- X2 x44: Screw Plug
- Y x24: Nut
- Z1 x56: Bolt M6*15mm
- Z4 x2: Waterproof Washer
- Z5 x8: Expansion Bolts
- ZX1: Middle Wall Connection
- Allen Wrench
Parts List-A
- A x2: Top Back Leg
- D x4: Side Beam
- E x22: Board Arm
- F x20: Board Protection
- H x4: Arm Connection
- I1 x2: Arm Hold Tube (Middle)
- I2 x2: Arm Hold Tube (Side)
Parts List-C
- K x20: UV Protected Board
Assembly Instruction SS16410 - STEP 1
Attach part A (x3) to part C (x6) using part L (x6) and part W1 (x48). Attach part B (x3) to part C (x6) using part L (x6) and part W1 (x48). A diagram illustrates the connection of A/B to C with W1.
Assembly Instruction SS16410 - STEP 2
Connect parts A and C using M (x14), W2 (x12), W1 (x2), Z1 (x12), and X1 (x12). A close-up view shows the connection of M to A and C with W2 and W1. Another close-up shows the connection of M to C with W2, X1, and Z1.
Assembly Instruction SS16410 - STEP 3
Assemble the frame structure using parts D (x4), D4 (x4), N (x4), N1 (x2), and U (x4). Use W1 (x48) for connections. Diagrams show the assembly of these parts with W1, and close-ups illustrate the connections of D/D4 with W1.
Assembly Instruction SS16410 - STEP 4
Connect the assembled frame sections using parts D (x4), D4 (x4), and Y (x24). A diagram shows the connection of A/B sections with D/D4 and Y.
Assembly Instruction SS16410 - STEP 5
Attach parts O (x2) and P (x2) to the frame using W1 (x12) and Z4 (x2). A diagram shows the main assembly with close-ups illustrating the attachment of O and P with W1 and Z4. The text notes that the Z4 position is movable.
Assembly Instruction SS16410 - STEP 6
Attach parts E (x22) to the frame using S (x11), T (x11), W5 (x44), Z1 (x44), and X2 (x44). A close-up view shows the connection of E with S, T, W5, Z1, and X2.
Assembly Instruction SS16410 - STEP 7
Connect parts E to the frame using Q (x22), V (x22), W1 (x44), W4 (x22), and H (x11). Diagrams show the main assembly and close-ups of connections involving Q, V, W1, W4, and H.
Assembly Instruction SS16410 - STEP 8
Attach part Q (x22) to parts E and D/D4 using W1 (x44). The tips state that Part Q is used by slotted holes, and to use the same sides of both holes to make the top side of Q higher than Part D for stronger support of the cover board.
Assembly Instruction SS16410 - STEP 9
Assemble the roof structure using parts I (x2), J (x4), V (x2), I1 (x2), and I2 (x1). Use W1 (x16) for connections. Diagrams show the assembly process and close-ups of connections involving I, J, V, I1, I2, and W1.
Assembly Instruction SS16410 - STEP 10
Secure the roof structure using part W4 (x11) and H (x11). The diagram shows the placement of W4 and H on the assembled pergola.
Assembly Instruction SS16410 - STEP 11
Place the UV Protected Boards (K x10) onto the assembled roof structure. An arrow indicates the direction of placement.
Assembly Instruction SS16410 - STEP 12
Attach parts F (x10) using R (x11) and W1 (x11). Diagrams show the attachment of F with R and W1 to the roof structure.
Assembly Instruction SS16410 - STEP 13
Install part G (x10) onto the roof structure. A close-up view shows the correct orientation of G, noting that each side has a drainage hole and should be installed facing upwards to prevent water leakage.
Assembly Instruction SS16410 - STEP 14
Place the remaining UV Protected Boards (K x10) onto the roof structure. An arrow indicates the direction of placement.
Assembly Instruction SS16410 - STEP 15
Attach parts F (x10) using R (x11) and W1 (x11). Diagrams show the attachment of F with R and W1 to the roof structure.
Assembly Instruction SS16410 - STEP 16
Secure the structure to the ground or wall using Expansion Bolts (Z5 x8) and M (x8). The diagram provides dimensions for placement: 164cm height, 4cm from edges, 557.3cm width, 230cm height, and 5cm from edges. A close-up shows the connection of M and Z5.
