ASSEMBLY INSTRUCTIONS SS16401

8'X10' Attached Pergola

Welcome

Thank you for choosing our product. Please read the contents on the second page carefully.

Before starting the installation, please thoroughly check the listed accessories below and read this manual attentively. Then proceed with the assembly step by step. If you have any questions, please don't hesitate to contact us.

Attention

Thank you for trusting us. You are entitled to a one-year warranty and lifelong customer service. Detailed notes are provided on the second page.
Our gazebo is packaged in 2 boxes. Box A contains all the frames, while Box B contains all the top panels.
We encourage you to reach out to us at the earliest if you encounter any issues.
We kindly request your attention to installation safety and child safety.

Important Notes for Customers

Before you begin the installation, please take a few minutes to carefully read the following important notes and be aware of your rights and entitlements.

Some of Your Concerns:

Package Damage: If you find any damage to the package upon arrival, resulting in loss of internal components or visible damage, please contact us. We will take responsibility for any damages caused during transportation.
Package Receipt: Please ensure that you begin installation after receiving both boxes of the package. If not, please contact us to inquire about the corresponding package status, and we will respond within 24 hours.
Product Stability: Product stability has been tested: the product can withstand winds of approximately 40-60 mph and a static pressure test of 6.5 lbs per square foot after correct installation and fixation. (Snow accumulation of about 7 inches in thickness will not pose a threat to the product.)
Questions & Support: If you have any questions regarding accessory defects, product use, or product installation, please feel free to contact us. We have simple installation videos available for you.

Some Precautions:

Use the provided tools to secure the gazebo to the wall for stability. Please purchase matching ground stakes separately for securing the product to the ground according to your installation plan. If you are unsure about how to choose, please let us know.
Please tighten the screws after ensuring that all screw holes have been properly inserted to avoid uneven hole alignment.
Please use a ladder when installing the top part.
Keep children away during the installation process, as the product contains small parts that could be swallowed.
Do not choose to install the product in strong winds or severe weather conditions.

Your Rights And Benefits:

You are entitled to a one-year warranty on the product and lifelong 24/7 customer service.
If you wish to connect multiple products together through DIY, please contact us for advice on the connections or to seek the necessary accessories for your construction needs.
We are introducing our brand-new adjustable and expandable support columns, designed to meet your utmost stability requirements. Feel free to get in touch with us if you're interested.

Parts List

Parts List-A

A
Top Back Leg (X2)

B
Top Front Leg (X2)

C
Bottom Leg (X4)

D
Side Beam (X4)

E
Board Arm (X12)

F
Board Protection (X10)

G
Drainage Piece (X5)

H
Beam Connector (X6)

I
Cross Beam (X2)

J
Connector (X1)

L
Middle Board Connection (X4)

M
Arm Connection (X10)

N
Arm Hold Tube(Side) (X2)

O
Arm Hold Tube Connection (X1)

P
Leg Connection (X1)

Q
Wall & Floor Connection (X12)

R
Beam Connection (X12)

S
Right Beam Hold (X6)

T
Left Beam Hold (X6)

U
Arm & Beam Connection (X4)

V
Arm Protection (X14)

W1
Bolt M6*13mm (X122)

W2
Bolt M6*70mm (X8)

W4
Bolt M6*35mm (X18)

W5
Bolt M6*50mm (X24)

X1
Screw Plug (X8)

X2
Allen Wrench (X24)

Y
Bolt M6*15mm (X16)

Z1
Nut (X32)

Waterproof Washer
Waterproof Washer (X24)

Z5
Expansion Bolts (X4)

Parts List-B

K
UV Protected Board (X10)

Assembly Steps

STEP 1

Connect vertical poles (A, B) to horizontal connectors (L) using bolts (W1).

Diagram shows two sets of vertical leg assemblies (A+C, B+C) being joined by L connectors using W1 bolts. The A/B labels indicate the top sections of the legs.

Parts used: A (X2), B (X2), C (X4), L (X4), W1 (X32).

STEP 2

Attach base connectors (M) to the bottom of the leg assemblies (C) using bolts (W2) and nuts (Z1), and screws (X1).

Diagram shows leg assemblies (A+C, B+C) with M connectors attached at the bottom. The M connector is secured to the C leg using W2 bolts and Z1 nuts, and X1 screws.

Parts used: M (X10), W2 (X8), Z1 (X8), X1 (X8).

STEP 3

Connect horizontal beams (D) to the leg assemblies. Use connectors (N) and (U) with bolts (W1).

Diagram shows horizontal beams (D) being attached to the vertical leg structures. N connectors are used on one end of D, and U connectors on the other, secured with W1 bolts.

Parts used: D (X4), N (X2), U (X4), W1 (X16).

STEP 4

Attach horizontal beams (D) to the leg assemblies using bolts (Y).

Diagram shows more horizontal beams (D) being attached to the vertical leg structures, specifically connecting to the A/B parts of the legs using Y bolts.

Parts used: D (X4), Y (X16).

STEP 5

Attach brackets (O, P) to the leg assemblies using bolts (W1).

Diagram shows brackets (O and P) being attached to the leg structures, likely for support or connecting other parts, secured with W1 bolts.

Parts used: O (X1), P (X1), W1 (X8).

STEP 6

Attach horizontal support beams (E) to the leg assemblies using bolts (W5), nuts (Z1), and screws (X2).

Diagram shows multiple horizontal support beams (E) being attached to the vertical legs. The attachment uses W5 bolts, Z1 nuts, and X2 Allen wrenches for tightening.

Parts used: E (X12), W5 (X24), Z1 (X24), X2 (X24).

STEP 7

Attach side beams (H) and connectors (Q, V) to the horizontal beams (E) using bolts (W1, W4).

Diagram shows side beams (H) and connectors (Q, V) being attached to the main horizontal beams (E). The attachment uses W1 bolts for Q and V, and W4 bolts for H.

Parts used: Q (X12), V (X12), W1 (X24), W4 (X12), H (X6).

STEP 8

Attach horizontal beams (E) to the leg assemblies using bolts (W1) and connectors (Q).

Diagram shows the main horizontal beams (E) being attached to the top of the leg assemblies, forming the main frame. This is secured with Q connectors and W1 bolts.

Parts used: E (X24), W1 (X24), Q (X12).

STEP 9

Attach cross beams (I) using bolts (W1, V).

Diagram shows cross beams (I) being attached to the structure. J connector is used with I, secured by W1 bolts and V parts.

Parts used: I (X2), J (X1), W1 (X4), V (X2).

STEP 10

Attach cross beams (I) using bolts (W4).

Diagram shows more cross beams (I) being attached to the structure, secured with W4 bolts.

Parts used: I (X6), W4 (X6).

STEP 11

Place UV Protected Boards (K) onto the frame.

Diagram shows placing the UV Protected Boards (K) onto the assembled frame, covering the top.

Parts used: K (X5).

STEP 12

Attach support brackets (R) and F parts to the frame using bolts (W1).

Diagram shows attaching support pieces (F) and brackets (R) to the underside of the roof structure, secured with W1 bolts.

Parts used: R (X6), W1 (X6), F (X5).

STEP 13

Install drainage pieces (G) into the top panels (K).

Diagram shows inserting drainage pieces (G) into the roof panels (K). Each G piece has a drainage hole.

Note: Each side of the 'G' has a drainage hole. Make sure to install with the side containing the drainage hole facing upwards (the higher side) to prevent water leakage.

Parts used: G (X5).

STEP 14

Place additional UV Protected Boards (K) onto the frame.

Diagram shows placing more UV Protected Boards (K) onto the frame, completing the roof covering.