Bazyths Smart Toilet Instruction Manual

Introduction

Thank you for purchasing the Bazyths Smart Toilet. Before using, please read this instruction carefully and keep it for future reference. Our company reserves the right of final interpretation for this manual. The manual is subject to change without notice.

Catalogue

This document covers the following topics:

• Packing List (Page 02)
• Installation of the Battery Box (Page 04)
• How to Use the Foam Shield Function (Page 05)
• Components (Page 06)
• Technical Drawing (Page 07)
• Features (Page 07)
• Attentions (Page 10)
• Installation Instruction (Page 17)
• Preparation before Use (Page 22)
• Panel Instruction (Page 23)
• How to Use (Page 26)
• Function Setting and Adjustment (Page 27)
• Cleaning and Maintenance (Page 32)
• Troubleshooting (Page 36)
• Warranty (Page 37)
• Function List (Page 38)
• Product Specification (Page 39)
• Acceptance Record (Page 40)

Packing List

Please count the following items after opening the package:

• Smart Toilet Unit
• Remote Control & Mounting Bracket (Requires 2 AAA alkaline batteries, not included)
• Wax Ring Gasket
• Flexible Flange Seal Strip
• Instruction Manual
• Backup Battery Box for Power Outage Flush (Requires 10 AA alkaline batteries, not included. Purchase separately or contact support@bazyths.com for free batteries.)

Included Components & Spare Parts:

• 1 Braided Hose (for Flushing Water)
• 1 Plastic Hose (for Cleansing Water) (Pre-installed)
• Spare Part: 3/8" Female to 1/2" Male Adapter (Use if your existing shut-off valve has a 3/8" outlet)

Diagram Description: A diagram shows the components of the T-Valve assembly, including a shut-off valve, T-valve with filter, water inlet, and various connectors. Another diagram shows the components for the battery box for power outage flush.

Battery Box for Power Outage Flush

Installation of the Battery Box for Power Outage

1. This battery box serves as backup during power outages. It must not be used simultaneously with a plugged-in power source. Connect it to the main unit only during power outages. The manufacturer is not responsible for consequences of using dual power sources, and such usage is not covered by warranty.
2. Install 10 AA alkaline batteries (not included) into the battery box. Open the box with a screwdriver. Do not mix new/old batteries, different models, or brands. Replace all batteries simultaneously. Contact support@bazyths.com for free batteries.
3. Follow the "+" and "-" signs when installing batteries. This is a series battery group; reversing a cell can cause damage or safety hazards like explosion/combustion.
4. Connect the battery connection cable from the rear of the seat cover to the battery box.
5. Do not disassemble the battery box unnecessarily. Seal it tightly after replacing batteries to prevent moisture damage.
6. When replacing batteries, disconnect the battery box from the main unit.
7. This battery box cannot be recharged.

How to Use the Foam Shield Function

Introduction to the Foam Shield Function

The Foam Shield creates a soft foam layer inside the toilet bowl to prevent splashing, block odors, and keep the bowl cleaner. This feature enhances hygiene and provides a more comfortable bathroom experience.

How to Get Your Free Foam Shield Liquid

For transportation safety, the foam liquid is not pre-filled. Contact support@bazyths.com after receiving your toilet to request the foam liquid. The first bottle is free.

Replace the Foam Shield Bottle

1. Hold both hands on the left and right sides of the decorative cover and lift it vertically.
2. Press the connector cap and detach the soft tube.
3. Remove the old bottle.
4. Attach the connector head from the old bottle to the new bottle.
5. Place the new bottle back into the machine and reconnect the soft tube.
6. Secure the decorative cover back in place.

Note: Ensure a foam liquid bottle is placed and the soft tube is connected, regardless of whether the Foam Shield function is used, to prevent water leakage.

Components

Diagram Description: An illustration of the smart toilet shows the Seat Cover/Lid, Operation Panel, Display, Dryer Device, Cleaning Nozzle, Seat Sensor, Seat Ring, Toilet Body, Foot Kick, Hose for Cleansing water, Shut-off valve, T-Valve with Filter, Hose for Flushing water, and Remote Control.

Features

Technical Drawing

Diagram Description: A technical drawing shows the dimensions of the smart toilet: Height 17.5 inches, Depth 26.8 inches, Width 15.7 inches, and base width 11.81 inches.

Automatic Opening of the Toilet Lid / Automatic Closing of the Lid & Toilet Seat

The lid opens automatically when a user approaches. It closes 2 minutes after the user leaves the sensor range. This function can be turned on/off via the Dryer button on the remote control.

Foot Kick to Open/Close the Lid or Seat

This hands-free feature allows users to open or close the toilet lid or seat by pressing a button with their foot. It is hygienic, simple, and intuitive.

Rear Wash

Water is released from a single nozzle for powerful cleaning. The cycle lasts 90 seconds. It can be stopped by holding the side button on the toilet for 2 seconds (while seated) or by pressing the "Stop" button on the remote control.

Feminine Wash / Front Wash

Designed for gentle cleaning specifically for female use.

Warm Air Dryer

The warm air dryer has 4 temperature settings: room temperature, high, medium, and low, for drying after cleansing.

360° Foam Shield

Activates automatically upon sitting, creating a foam layer that prevents splashing, blocks odors, and resists bacteria for a cleaner, more hygienic experience.

One-Twist Quick Mode (Wash + Flush + Dry)

When a cleaning mode is activated, the system performs a sequence: wash (90 seconds), flush, and dry (3 minutes). The wash cycle can be skipped to proceed directly to flushing and drying by pressing the wash button again.

Remote Control

All functions are accessible via the wireless remote control.

Rear Wash with Moving Nozzle

The nozzle moves back and forth for thorough cleaning over a wider area. Toggle between moving and non-moving cleaning by briefly pressing the rear wash button again on the remote control.

Feminine Wash with Moving Nozzle

The nozzle moves back and forth for gentle cleaning over a wider area.

Cleansing Strength Adjustment

Adjust cleansing strength/water pressure to your preference.

Cleansing Position Adjustment

Adjust the nozzle's back-and-forth position for optimal cleaning.

Cleansing Water Temperature Adjustment

4 levels of cleansing water temperature: normal (room temperature), high, medium, and low.

Seat Sensor

Corresponding functions activate when the user is seated.

Attentions

⚠️ WARNING:

• Do not pull the plug with wet hands. ? Otherwise, it may cause electric shock.
• Do not pour water, detergent, or deodorant on the smart toilet main unit and power plug. ? Otherwise, it may cause fire, electric shock, short circuit, or damage.
• When there is thunder, do not touch the power plug. ? Otherwise, it may cause electric shock.
• Do not touch the water inlet hose to the power plug or outlet. ? Otherwise, it may cause fire, electric shock, heating, or short circuit due to condensation.
• Do not damage the power cord or plug (do not drop, pull, twist, bend, scratch, process, heat, place heavy objects on, tie, or clamp). ? Otherwise, it may cause product damage, fire, electric shock, heating, or short circuit.
• Do not use power outlets that are loose or malfunctioning. ? Otherwise, it may cause fire or short circuit.
• Please use power outlets and wiring tools within the specified range. Exceeding the specified range may cause fire due to overheating.
• Do not use a power source other than the specified one (AC 120V, 60Hz). Do not plug in until the inlet valve opens. ? Otherwise, it may cause fire.
• Do not disassemble, repair, or modify this product on your own. ? Otherwise, it may cause fire, electric shock, heating, short circuit, or damage.
• Do not install on a moving vehicle, ship, or other mobile structure. ? Otherwise, it may cause fire, electric shock, short circuit, or malfunction. The seat ring, seat cover, and main unit may be damaged due to detachment and falling.

❗ MANDATORY:

• When the smart toilet malfunctions, do not continue to use it. Turn off power and close the water inlet valve in the following situations:
• Water leaks from the hose or product.
• The product has cracks or damage.
• Abnormal sound or odor.
• Product smoking.
• Product abnormal heating.
• The cushion of the seat ring falls off.
• Continuing to use the product in a malfunctioning state may cause fire, electric shock, heating, short circuit, injury, or indoor water seepage.
• Beware of low-temperature burns. Improper use of the warm seat ring may result in burns. If sitting for a long time, set the seat ring temperature to normal/unheated. For children, the elderly, individuals with behavioral impairments, those who have taken hypnotic drugs, heavy drinkers, or excessively fatigued individuals, use under supervision and set temperatures to the lowest setting.
• Please confirm that the power outlet has been waterproofed and is away from the bathtub. If not waterproofed, it may cause fire or electric shock. Consult qualified professionals for installation and waterproofing.
• Please confirm the outlet is correctly grounded. Otherwise, it may cause electric shock. Entrust a professional company for ground wire installation.
• Do not use water sources other than tap water or potable well water (groundwater). ? Otherwise, it may cause corrosion, malfunctions, or skin inflammation/burns from unclean water.
• Do not put fingers or other objects into or block the warm air outlet, and do not place or cover objects on the warm air outlet. ? Otherwise, it may cause burn, electric shock, or burning of accessories.

Installation Instruction

1. Confirmation of Installation Environment

Before installation, confirm that the bathroom wall and floor tiles are completed, and sewage pipes, water pipes, and electrical circuits are reserved. This toilet has a rough-in of 300mm (11.81in). Water inlet pressure range: 0.15Mpa (dynamic) - 0.75Mpa (static). Water inlet temperature: 4°C-35°C (39.2°F-95°F).

Diagram Description: A diagram shows the required clearances for installation: Over 300 mm (11.81 in) from the wall, 330 mm (12.99 in) from the side wall, 280 mm (11.02 in) from the back wall, and 100 mm (3.94 in) for water inlet and drain outlet.

2. Assembly of Dedicated Shut-off Valve

Install the provided shut-off valve. Note: If your existing shut-off valve has a 3/8" outlet, use the Spare Adapter (Refer to page 3) to connect it to the smart toilet.

Diagram Description: An illustration shows the installation of the shut-off valve on the wall.

3. Installation and Fixation of the Toilet

Note: The included flange is designed for a 4-inch drain pipe. For a 3-inch pipe, purchase a compatible flange locally. Install the flange about 1/4 inch (0.6 cm) above the finished floor to prevent leaks.

1. Align the "flange-ABS" on the ground drain outlet, point the arrow vertically to the wall, and mark drilling positions. Drill four holes.
2. Install the "Flexible Flange Seal Strip" at the bottom of "flange-ABS".
3. Insert the "expansion plastic sleeve - small" into the small hole. Align holes, install "flange-ABS" and "sealing wax ring-thin". Use "round head self tapping screw-5×36mm" to lock.
4. Insert "bolt-8×43mm" into the "flange-ABS" slot. Adjust bolts to be perpendicular to the arrow on the flange body.

Diagram Description: Illustrations show the steps for installing the flange, seal strip, and securing the toilet base with screws and bolts.

(3) Caulk the bottom of the toilet with silicone sealant.

Diagram Description: An illustration shows silicone sealant being applied to the base of the toilet.

4. Connection of the Water Inlet Hose

Connect the inlet hose with the shut-off valve & T-valve using a wrench. (Refer to Page 3 for Valve Installation Details).

Notice: After installation, turn on the shut-off valve to check for leaks.

Diagram Description: An illustration shows the connection of the inlet hoses to the T-valve and shut-off valve.

Preparation before Use

1. Open the Shut-off Valve: Turn the valve counterclockwise to fully open the water supply.
2. Plug the Power Plug into the Outlet: Plug into a 120V power outlet. The smart toilet will perform a self-check (lid/seat automatically open/close). The main unit will be in standby mode. Do not use extension cords. The outlet must be reliably and safely grounded.
3. Adjust Cleansing Water Temperature and Seat Temperature: Set to the appropriate levels.
4. Refer to Function Setting and Adjustment (Page 27): Use the remote control to operate various functions.

Panel Instruction

This product is primarily operated via remote control, with main unit panel operation as a supplement.

Remote Control Panel

Diagram Description: An illustration of the remote control shows buttons for Stop/Power ?, Rear cleansing ?, Front cleansing ?, Flushing ?, Bubble Shield ?, Seat ring opening ?, Seat cover opening ⬆️, Water temp. ?, Seat temp. ?️, Wind temp. ?, Energy saving / Night light ?.

Remote Control Code Matching Operation Instructions

Within 30 seconds after power-on, in the off-seat state: Long press "Front cleansing" for 3 seconds (display blinks, buzzer sounds ?). Then press "Rear cleansing" (display blinks and buzzes). This enters alignment mode (exits after 15 seconds). Press the "Stop" button ? on the remote control to complete alignment (display stops blinking, buzzer stops).

Host Operation Panel

Diagram Description: An illustration of the main unit panel shows buttons for Front Cleansing, Flush/Stop, and Rear Cleansing.

• In the unseated state, press "Flush/Stop" to manually flush ?.
• In the seated state, press "Rear cleansing" ? for one-key operation.

When Seated on the Toilet Seat

After sitting down, press the front or rear cleansing button for a one-touch cleansing mode (90 seconds wash + flush + 3 minutes dry). If less than 90 seconds of cleansing is desired, press the button again to stop cleansing and proceed to flushing/drying.

Display Screen

Diagram Description: An illustration shows the display screen with icons and numbers.

• Power indicator: Lights up when the host is powered on ?.
• Temperature level: Shows the set temperature.
• Wind temperature icon (?): Shows warm air temperature setting.
• Seat temperature icon (?): Shows seat temperature setting.
• Water temperature icon (?): Shows water temperature setting.
• The digital tube displays the set temperature; cycles through water temperature, seat temperature, and wind temperature every 30 seconds.

Ambient Light

Diagram Description: An illustration points to the ambient light on the toilet.

The display screen turns off automatically about 30 seconds after the user leaves the sensor area and the seat cover closes. Long press the drying button to turn the ambient light on/off. The light turns on when a human body is near the sensor area and off after about 30 seconds of leaving.

How to Use

When Seated on the Seat

• When you hear the "beep" sound ?, all functions begin to start.
• Auto clean the nozzle once ?.

Start Rear Cleaning or Front Cleansing Function

Diagram Description: An illustration shows the seat ring and cleaning nozzle.

• Start rear cleaning or front cleaning by remote control ?.
• Adjust cleaning position and water pressure by remote control.
• Start drying function by remote control ?.
• Press the "Stop" button ? to stop rear cleaning, front cleaning, or drying.

When Unseated on the Seat

• Auto flush the toilet once ?.

Function Setting and Adjustment

How to Turn On/Off the Radar Sensor Function

When a user approaches, the lid automatically opens. Long press the rear cleansing button on the remote control to enable or disable this function.

Lid/Seat Opening

The toilet has lid/seat opening functionality. Approach the toilet and foot kick the sensor to open the cover and seat ring. Press the lid/seat opening button on the remote control to open/close the cover and seat ring.

• Lid/Seat Opening by Foot Kick:
• Unseated state: Gently foot kick the sensor once to open the seat cover (if in low position).
• Gently foot kick once to open the seat ring (if seat cover is high and seat ring is low).
• Gently foot kick once to close the seat ring and cover, and flush once (if both are high). If the last operation was flushing, it will not flush again after closing.
• Lid/Seat Opening by Remote Control:
• Unseated state: Press "Lid Up" button ⬆️ to open/close seat cover.
• Press "Lid Up" button to close seat cover and flush once (if seat cover and ring are high).
• Press "Seat Up" button ? to open/close seat ring.

Note: Lid/seat opening function is suspended during rear cleansing, front cleansing, or flushing.

Rear Cleansing

Features single-hole powerful cleansing. Press the "Rear cleansing" button ? on the remote control to enter reciprocating cleansing mode (nozzle moves back and forth). Pressing again enters reciprocating cleansing. Pressing again stops movement and switches to cleansing mode. The operation can be repeated.

The rear cleansing function automatically stops after 90 seconds. It can be switched to other functions or stopped by pressing the "Stop" button ?. The nozzle auto-cleans before and after rear cleansing.

Front Cleansing

Features a special spray hole for gentle cleaning for women. Press the "Front cleansing" button ? on the remote control to enter reciprocating cleansing mode (nozzle moves back and forth). Pressing again enters reciprocating cleansing. Pressing again stops movement and switches to cleansing mode. The operation can be repeated.

The front cleansing function automatically stops after 90 seconds. It can be switched to other functions or stopped by pressing the "Stop" button ?. The nozzle auto-cleans before and after front cleansing.

Water Pressure Adjustment

In rear or front cleansing mode, press the water pressure button on the remote control to adjust water strength. 4 levels of water pressure are available.

Nozzle Position Adjustment

In rear or front cleansing mode, press the nozzle mast button on the remote control to move the nozzle back and forth and adjust the cleaning position. 4 levels of nozzle position are available.

Cleansing Water Temperature Adjustment

Press the water temp. button ? on the remote control. It can be adjusted to a comfortable water temperature for cleansing. 4 levels: Normal, high, medium, and low. The temperature switches each time the button is pressed.

Drying Function

Press the drying button ? on the remote control to dry the wet part after cleansing. The function automatically stops after 3 minutes. It can be stopped within 3 minutes by pressing the "Stop" button ?.

Drying Temperature Adjustment

Press the drying temp. button ? on the remote control. It can be adjusted to a comfortable drying temperature. 4 levels: Normal, high, medium, and low. The temperature switches each time the button is pressed.

Seat Ring Temperature Adjustment

Press the seat temp. button ?️ on the remote control. It can be adjusted to a comfortable seat ring temperature. 4 levels: Normal, high, medium, and low. The temperature switches each time the button is pressed.

Night Light

This product has a lighting function for nightly use. Long press the night lamp button to turn the lighting function on/off.

Nozzle Cleaning

Press the self-cleaning button ? on the remote control. Water flows out to clean the nozzle. This function can only be activated when unseated. It runs for 90 seconds and can be stopped by pressing the "Stop" button ?.

Power Button

Long press the power button ? on the remote control to turn the host system on or off.

Flushing by Remote Control

Press the flushing button ? on the remote control to flush once. Continuous flushing requires a 30-second interval. Flushing will stop any active cleansing function.

Flushing Manually

In the off-seat state, briefly press the flush button on the host side to flush once. Flushing will stop any active cleansing function. Pressing again will conduct flushing.

Flushing by Foot Kick

Designed for men to urinate. Gently foot kick the sensor to achieve flushing without bending down.

Flushing When Power Off

In the absence of mains power, long press the flush button on the host side for 3 seconds to activate the power outage flushing function.

Foam Shield

Manual foaming: Press the foam shield function key on the remote control to trigger the foam function once.

Auto-foaming: It will auto-foam once after sitting. Long press the remote control seat temperature function button ?️ for 3 seconds to turn on/off the automatic foaming function.

Cleaning and Maintenance

Clean and Maintain the Power Plug

Clean the power plug regularly. Remove it from the outlet and wipe with a dry cloth. Dust accumulation on the power plug may cause fire ?.

Clean and Maintain the Main Unit of the Smart Toilet

Wipe the surface with a soft, wet cloth. Pull the power plug out of the outlet before cleaning. For stubborn stains, use a soft, wet cloth with neutral kitchen detergent.

Clean and Maintain the Ceramic Part of the Smart Toilet

Use a neutral toilet cleaner on a soft brush or sponge. Rinse with tap water. Do not use detergents or disinfectants containing chlorine or acids. Do not use abrasive brushes.

Clean and Maintain the Nozzle

When the smart toilet is on, press the self-cleaning button ? on the remote control to extend the nozzle for cleaning. You can use a toothbrush simultaneously. Do not forcefully stretch the nozzle. The nozzle can be removed and cleaned separately.

Detachable Nozzle Model Cleaning Method

1. Press the self-cleaning button ? on the remote control to extend the nozzle.
2. With the nozzle extended, pull out the front nozzle by hand.
3. Use a toothbrush to clean the nozzle.

Clean and Maintain the Water Inlet Filter in the T-Valve

• Turn off the shut-off valve first.
• Remove the lock and the filter from the T-valve.
• Clean the filter with a brush or running water ?.
• Reinstall the filter securely.

Notice: After cleaning and reinstalling the filter, turn on the supply valve and check for leaks. Reinstall if necessary.

Diagram Description: Illustrations show the removal and cleaning of the water inlet filter.

When Not in Use for a Long Time

Drain all water from the smart toilet and absorb remaining water with a dry towel to prevent deterioration and freezing ?. Turn off the power and remove the battery from the remote control ?.

1. Close the shut-off valve and stop the water supply.
2. Unplug the power plug from the outlet ?.
3. Remove the water hose from the shut-off valve, drain it, and then reinstall it.

Troubleshooting

Some malfunctions can be resolved by simple operations. Please confirm the following items before authorizing a professional repair.

Warranty

Warranty Period

One year from the date of purchase.

What's Covered

This product is warranted to be free of defects in materials and workmanship for one year. During the warranty period, if any defects or malfunctions occur, Bazyths will provide free replacement parts to ensure your satisfaction.

Note: This warranty is limited and does not cover damage caused by improper use or maintenance.

Caution

• Prohibited Cleaners: Do not use cleaners containing abrasive materials, ammonia, bleach, acids, waxes, alcohol, solvents, or any other products not recommended for chrome finishes. Doing so may damage the product and void the warranty.
• Proper Use and Maintenance: Ensure the product is used and maintained according to the user manual. Failure to follow these instructions may result in damage not covered under warranty.

Function List

● Indicates this product contains the function.

Product Specification

* Rated power: When this product works under the condition of circumstance temp. 23°C (±2°C), water-input pressure 0.24MPa(±0.02MPa), water-input temp. 15°C (±0.5°C), max cleaning flow (front cleansing at highest level), seat temp. highest level and water temp. highest level, test the average power of cleaning in a minute.

Acceptance Record

After the installation is complete, please test run the toilet and fill out the record sheet with the results:

Remark:

Retailer: ____________________ Installation personnel: ____________________ Acceptance tester: ____________________ Date: ____________________