Bazyths ZYC8A Smart Toilet

Introduction

Thank you for purchasing the Bazyths Smart Toilet. Before using, please read this instruction carefully and keep it for future reference. Our company reserves the right of final interpretation for this manual, which is subject to change without notice.

For any questions, please contact Bazyths Support at support@bazyths.com.

Catalogue

This document serves as a comprehensive guide for your Bazyths Smart Toilet. The following sections cover various aspects of the product:

• Packing List
• Installation of the Battery Box
• How to Use Foam Shield & Toilet Bowl Cleaner Tablets
• Components
• Technical Drawing
• Features
• Attentions (Safety Warnings)
• Installation Instruction
• Preparation before Use
• Panel Instruction
• How to Use
• Function Setting and Adjustment
• Cleaning and Maintenance
• Troubleshooting
• Warranty
• Function List
• Product Specification
• Acceptance Record

Packing List

Please count the following items after opening the package:

• Smart Toilet Unit
• Remote Control & Mounting Bracket (Requires 2 AAA alkaline batteries, not included)
• Flange, Sealing Wax Rings, Mounting Accessory Kit
• Backup Battery Box for Power Outage Flush (Requires 10 AA alkaline batteries, not included)
• Instruction Manual
• 1 Braided Hose (for Flushing Water)
• 1 Plastic Hose (for Cleansing Water) (Pre-installed)
• Spare Part: 3/8" Female to 1/2" Male Adapter (If your existing shut-off valve has a 3/8" outlet, use this adapter to connect to your smart toilet without replacing the valve.)

Battery Box for Power Outage Flush

Installation of the Battery Box for Power Outage

This battery box serves as a backup during power outages and should not be used simultaneously with a plugged-in power source during operation. It is recommended to connect it only during power outages.

1. Install 10 AA alkaline batteries (not included) into the battery box. Do not mix new/old, different models, or brands. Replace all batteries simultaneously. Follow the "+" and "-" signs carefully; reversing a cell can cause damage or safety hazards.
2. Take out the battery connection cable from the rear side of the seat cover and connect it to the battery box.
3. Do not disassemble the battery box. Seal it tightly after replacing batteries to prevent moisture ingress.
4. When replacing batteries, disconnect the battery box from the main unit.
5. This battery box cannot be recharged.

How to Use Foam Shield & Toilet Bowl Cleaner Tablets

Introduction to the Foam Shield Function

The Foam Shield creates a soft foam layer inside the toilet bowl to prevent splashing, block odors, and keep the bowl cleaner, enhancing hygiene and comfort.

How to Get Your Free Foam Shield Liquid

For transportation safety, the foam liquid is not pre-filled. Contact support@bazyths.com to request your first free bottle.

Replace the Foam Shield Bottle

1. Hold the decorative cover on the sides and lift it vertically.
2. Press the connector cap and detach the soft tube.
3. Remove the old bottle.
4. Attach the connector head from the old bottle to the new bottle.
5. Place the new bottle back into the machine and reconnect the soft tube.
6. Secure the decorative cover.

Note: Ensure a foam liquid bottle is placed and the soft tube is connected, even if the Foam Shield function is not used, to prevent water leakage.

Toilet Bowl Cleaner Tablets Installation Instructions

1. Turn the arrow on the lid to "Open" and lift it.
2. Remove the "water-soluble film" from the cleaner tablet. Place the tablet (Diameter ≤ 45mm, Thickness ≤ 20mm) into the mixing chamber. ⚠️ Failure to remove the film may clog pipes.
3. Close the lid and turn the arrow to "Close." Flushing is not allowed if the lid is not properly closed.

Note: Toilet cleaner tablets are not provided due to shipping restrictions. Please purchase them locally.

Components

The smart toilet includes the following components:

• Lid
• Display Screen
• Button
• Drying Unit
• Nozzle
• Seat Sensor
• Toilet Seat
• Foot Sensor
• Ceramic Base
• Button
• Washing Water Path
• Shut-off Valve
• T-Valve with Filter
• Hose for Flushing water
• Foam Outlet
• Remote Control

Technical Drawing

Dimensions:

• Width: 27.83 inches (707 mm)
• Depth: 15.31 inches (389 mm)
• Height: 17.95 inches (456 mm)
• Rough-in distance (from wall to drain outlet center): 11.81 inches (300 mm)

Features

Automatic Opening of the Toilet Lid / Automatic Closing of the Lid & Toilet Seat

The lid opens automatically when a user approaches. The seat and lid close 2 minutes after the user leaves the sensor range. This function can be toggled on/off using the Dryer button on the remote control.

Foot Sensor to Open/Close the Lid or Seat

Opens or closes the toilet lid or toilet seat when the user moves their foot near the sensor.

Rear Wash

Water is released from a single nozzle for a powerful cleaning effect, lasting up to 90 seconds. The cycle can be stopped by pressing and holding the side button on the toilet (2 seconds, while seated) or by pressing the "Stop" button on the remote control.

Feminine Wash / Front Wash

Designed for gentle cleaning specifically for female use.

Warm Air Dryer

Offers 4 temperature settings (room temperature, high, medium, low) for drying after cleansing.

One-Twist Quick Mode (Wash + Flush + Dry)

Activates a sequence of wash, flush, and dry. Each cleaning cycle is 90 seconds, followed by a 3-minute drying cycle. The wash phase can be skipped to proceed directly to flushing and drying.

Remote Control

All functions are accessible via the wireless remote control.

Rear Wash with Moving Nozzle

The nozzle moves back and forth for thorough cleaning. Toggle between moving and non-moving modes by briefly pressing the wash button again on the remote.

Feminine Wash with Moving Nozzle

The nozzle moves back and forth for gentle cleaning.

Hot and Cold Massage

The nozzle alternates between warm and cool water for a massaging effect. Activate by pressing and holding the Feminine Wash button for 5 seconds while seated. The cycle alternates 10 seconds cool / 5 seconds warm water for 90 seconds. Press and hold again for 5 seconds to deactivate.

360° Foam Shield

Automatically activates upon seating, creating a foam layer to prevent splashing, block odors, and resist bacteria.

Compatible with Toilet Bowl Cleaner Tablets

Designed to work with cleaner tablets for enhanced cleaning efficiency, removing dirt and limescale while forming a protective layer.

Aperient / Enema

Provides a high-pressure water stream for relief of constipation or easier bowel movements. Activate by pressing and holding the Feminine Wash button for 5 seconds while seated. The nozzle position is fixed, and water is released at maximum flow for 90 seconds.

Cleansing Strength Adjustment

Adjust water pressure to your preference.

Cleansing Position Adjustment

Adjust nozzle position forward or backward.

Cleansing Water Temperature Adjustment

4 levels: normal (room temperature), high, medium, and low.

Seat Sensor

Activates functions when the user is seated.

Toilet Seat Temperature Adjustment

Heated seat with 4 levels: normal (room temperature), high, medium, and low.

Auto Off-Seat Flush

Automatically flushes when the user stands up from the seat.

Foot Kick to Flush

Flush by pressing the button with your foot.

Flush by Remote Control

Flush by pressing the flush button on the remote control.

Flush by Side Knob

Flush by pressing the side knob on the smart toilet.

Night Light

Provides gentle illumination for navigating the bathroom at night.

Nozzle Cleaning

Press and hold the corresponding button on the remote control when unoccupied for self-cleaning mode.

Nozzle Auto Cleaning

The nozzle automatically cleans itself before and after use.

Power Outage Flush

The backup battery box can be activated for flushing during a power outage.

Attentions (Safety Warnings)

Please observe the following warnings to ensure safe operation and prevent damage:

• ⚠️ WARNING: Do not pull the plug with wet hands.
• ? Do not pour water, detergent, or deodorant on the smart toilet main unit and power plug. This may cause fire, electric shock, short circuit, or damage.
• ⚠️ When there is thunder, do not touch the power plug. This may cause electric shock.
• ? Do not touch the water inlet hose to the power plug or outlet. This may cause fire, electric shock, heating, or short circuit due to condensation.
• ? Do not damage the power cord or plug. Do not forcefully drop, pull, twist, bend, scratch, process, heat, place heavy objects on, tie, or clamp the power cord or plug. Damage may lead to fire, electric shock, heating, or short circuit.
• ? Do not use power outlets that are loose or malfunctioning. This may cause fire or short circuit.
• ? Please use power outlets and wiring tools within the specified range. Exceeding the specified range may cause fire due to overheating.
• ? Do not use a power source other than the specified one (AC 120V, 60Hz). Plug in only after the inlet valve opens. This may cause fire.
• ? Do not disassemble, repair, or modify the product. This may cause fire, electric shock, heating, short circuit, or damage.
• ? Do not install on a moving vehicle, ship, or other mobile structure. This may cause fire, electric shock, short circuit, malfunction, or damage due to detachment and falling.
• ⚠️ When the smart toilet malfunctions, do not continue to use it. Turn off the power and close the water inlet valve if:
  • Water leaks from the hose or product.
  • The product has cracks or damage.
  • Abnormal sound or odor is present.
  • Product is smoking.
  • Product is abnormally heating.
  • The cushion of the seat ring falls off.
  Continuing use may cause fire, electric shock, heating, short circuit, injury, or water seepage.
• ❗ MANDATORY: Beware of low-temperature burns. Improper use of the warm seat ring can result in burns. If sitting for a long time, set the seat temperature to normal/unheated.
• Note for specific groups: Children, the elderly, individuals unable to adjust temperature, those with behavioral impairments, individuals who have taken hypnotic drugs, heavy drinkers, or excessively fatigued individuals should use this product under supervision.
• ❗ MANDATORY: Please confirm that the power outlet has been waterproofed and is kept away from the bathtub. If not waterproofed, it may cause fire or electric shock. Consult professionals for installation and waterproofing.
• ❗ MANDATORY: Please confirm that the outlet being used is correctly grounded. Otherwise, it may cause electric shock. Entrust a professional company for ground wire installation.
• ❗ MANDATORY: Do not pull out the power plug by holding the power cord. Hold the plug itself. This prevents damage to the power cord, which could cause fire or heating.
• ❗ MANDATORY: Please make sure to firmly insert the power plug into the outlet. Loose connections may cause fire, heating, or short circuit.
• ❗ MANDATORY: If the power cord is damaged, it must be replaced by the manufacturer, maintenance department, or other professionals.
• ❗ MANDATORY: When performing maintenance (except nozzle cleaning), turn off the power to avoid electric shock.
• ❗ MANDATORY: This is an electrical product. Do not install in places easily splashed with water or with high humidity. Ensure the bathroom is well-ventilated with an exhaust fan or ventilation opening. Otherwise, fire or electric shock may occur.
• ❗ MANDATORY: When removing the smart toilet main unit, disconnect the power. Otherwise, fire or electric shock may occur.
• ❗ MANDATORY: Individuals with physical, sensory, or cognitive disabilities, or those lacking experience and knowledge (including children), must use this product under supervision. Children should not play with this product. Otherwise, burn, electric shock, fire, or injury may occur.
• ? Do not let cigarettes or other sources of fire get close to the product. This may cause fire.
• ? When maintaining plastic parts (seat ring, seat cover, etc.) and water inlet hoses, use neutral kitchen detergent only. Do not use: toilet cleaner, household detergent, gasoline, benzene, washing powder, or nylon brushes. These can damage parts, cause cracks, or lead to water leakage.
• ? Do not forcibly impact the product. Do not place heavy objects on or stand on the seat ring, seat cover, or main unit. This may cause cracks, detachment, falling, personal injury, or water seepage.
• ? Do not use the smart toilet when its main unit is loose. This may cause detachment and falling, leading to personal injury.
• ? Do not lift the main unit by holding the seat ring or seat cover. Do not open the seat ring or seat cover when items are on them. This may cause detachment and falling, leading to personal injury.
• ? Do not violently open or close the seat cover or seat ring, or swing them quickly. This may damage the flipping device or cause the main unit to break or detach, leading to personal injury.
• ? Do not bend or damage the water inlet hose. This may cause water leakage.
• ? To prevent sudden water leakage, do not remove the filter in the T-valve when the shut-off valve is open. Water may spray out. Refer to page 33 for cleaning the water inlet filter.
• ? Please use the new hose component provided with the product. Old hoses cannot be reused and may result in water leakage or rupture.
• ❗ MANDATORY: When water leaks occur, turn off the shut-off valve immediately.
• ❗ MANDATORY: In order to prevent pipes or hoses from being damaged due to freezing, take anti-freezing measures. If the water inlet hose freezes, it may damage the main unit or pipes, causing water leakage. If the room temperature is below 32°F/0°C, empty the product's water to prevent internal cracking.
• ❗ MANDATORY: When the smart toilet is not used for a long time, drain the water from the main unit and water inlet hose, and disconnect the power supply. Before using again, let water flow through first. Otherwise, water deterioration may cause skin inflammation, or continuous power may cause fire or heating.
• ❗ MANDATORY: When installing the water inlet filter, ensure it is tightened firmly to the correct position to prevent water leakage.
• ❗ MANDATORY: Do not use any paper other than toilet paper, and do not drop objects that may clog the drain into the toilet bowl. This may cause blockages in the ceramic pipes.
• ? Do not operate the remote control with wet hands, and do not spill water on the remote control. This may cause remote control malfunctions.
• ? Do not put any solid substances or corrosive liquids into the water tank. This may cause blockages or corrosion of the flushing water pipe.

Installation Instruction

Installation of the Smart Toilet

1. Confirmation of installation environment

Before installation, confirm that bathroom wall and floor tiles are completed, and sewage pipes, water pipes, and electrical circuits are reserved. This toilet has a rough-in of 300mm (11.81in). Water inlet pressure range: 0.15Mpa (dynamic) - 0.75Mpa (static). Water inlet temperature: 4°C-35°C (39.2°F-95°F).

2. Assembly of dedicated shut-off valve

Install the shut-off valve provided with the product. A spare adapter is included for connecting to existing 3/8" shut-off valves.

3. Installation and fixation of the toilet

1. Align the "flange-ABS" on the ground drain outlet, orient the "flange-ABS" arrow vertically to the wall, and mark drilling positions. Drill four holes.
2. Install the "sealing wax ring-thin" at the bottom of "flange-ABS".
3. Insert the "expansion plastic sleeve - small" into the small hole. Align the hole position, install "flange-ABS" and "sealing wax ring-thin", and secure with "round head self tapping screw-5×36mm".
4. Insert the "bolt-8×43mm" into the slot of "flange-ABS", adjusting it so the center line of the bolts is perpendicular to the arrow on the flange body.
5. Align the "sealing wax ring-thick" with the drain outlet and install it on the "flange-ABS". Insert L-shaped plastic fixed blocks and gaskets into "bolt-7×43mm", then install the "large washer-8×24×1.8mm" and "nut 5/16".
6. Align the drain outlet of the intelligent toilet with the center of the flange for installation.
7. Install the "T-shaped pad" on the small holes on both sides of the ceramic pan, and drive in the "flat head self tapping screw-5×75mm".
8. Cover the "T-shaped pads" with the "decorative caps".

(3) Caulk the bottom of the toilet with silicone sealant.

4. Connection of the water inlet hose

Connect the inlet hose with the shut-off valve & T-valve using a wrench. (Refer to Page 3 for Valve Installation Details). Notice: After installation, turn on the shut-off valve to check for leaks.

Preparation before Use

1. Open the shut-off valve: Turn the valve counterclockwise to fully open the water supply.
2. Plug the power plug into the outlet: Plug into a 120V power outlet. The smart toilet will perform a self-check (lid/seat opens and closes, resets). Do not use extension cords. The outlet must be reliably and safely grounded.
3. Adjust the cleansing water temperature and the seat temperature to the appropriate level.
4. Refer to Function Setting and Adjustment on Page 27 and use the remote control to operate various functions.

Panel Instruction

Remote Control Panel

The product is designed primarily for remote control operation, with main unit panel operation as a supplement. The remote control features buttons for:

• Auto Lid
• Foot Sensor to Open the Lid
• 360° Foam Shield
• Blue Toilet Cleaner Tablets Function
• Aperient
• H/C Massage
• Rear Cleansing
• Rear Cleansing with Nozzle Oscillation
• Front Cleansing
• Front Cleansing with Nozzle Oscillation
• Cleansing Strength Adjustment
• Cleansing Position Adjustment
• Cleansing Water Temperature Adjustment
• Warm Air Dryer
• Seat Sensor
• Seat Ring Temperature Adjustment
• Remote Control
• Off Seat Auto Flush
• Foot Sensor Flush
• Flush by Remote Control
• Flush by Side Knob
• Night Light
• Nozzle Cleaning
• Nozzle Auto Cleaning
• Power Outage Flush
• Water Temperature (+/-)
• Seat Temperature (+/-)
• Wind Temperature (+/-)
• Long press for Closing Auto lid
• Long press for Auto temperature Control
• Long press to Closing Auto Foaming
• Long press for Night Light
• Seat Ring/Cover Up
• Seat Cover Closed

Remote Control Pairing Instructions:

1. Press and hold the "Rear Wash" button for 3 seconds. The display will flash once with a beep.
2. Press and hold the "Rear Wash" button again for 3 seconds. The display will flash, and a beep will sound, indicating pairing mode. (Exits after 15 seconds if no action).
3. In pairing mode, briefly press the "Stop" button. The display stops flashing, and the beeper stops sounding, indicating successful pairing.

Main Unit Control Panel

The main unit has buttons for Rear Wash and Front Wash. In the seat-off state, these buttons activate manual flushing. In the seated state, pressing Rear Wash starts one-press rear wash mode (press again for drying). Pressing Front Wash starts one-press front wash mode (press again for drying). Press and hold for 2 seconds to stop.

Main Unit Display Screen

• Power Indicator Light: Lights up when the main unit is powered on.
• Temperature Level: Displays the set temperature.

Icons on Display:

• Air Temperature Icon: Lights up for air temperature setting.
• Seat Temperature Icon: Lights up for seat temperature setting.
• Water Temperature Icon: Lights up for water temperature setting.

The digital display cycles through water, seat, and air temperatures every 30 seconds. The screen turns off approximately 30 seconds after the user leaves the sensing area.

Main Unit Ambient Light

Press and hold the nozzle position button on the remote control to turn the ambient light on/off. The light turns on when a user approaches and turns off automatically after 30 seconds.

How to Use

When Sitting on the Seat

Upon hearing a "beep" sound, the smart toilet functions activate. The nozzle cleans itself automatically.

Start Rear Cleansing or Front Cleansing Function

1. Start rear or front cleansing using the remote control.
2. Adjust cleansing position and water pressure via the remote control.
3. Start the drying function via the remote control.
4. Press the "Stop" button to stop the bidet function (rear cleansing, front cleansing, or drying).

When standing up from the seat

The toilet will auto flush once.

Function Setting and Adjustment

How to Turn On/Off the Radar Sensor Function

Press and hold the Water Temperature button on the remote control for 5 seconds. Note: The foot kick function for lid/seat opening still works when the radar sensor is off.

How to Adjust the Radar Sensor Distance

The radar sensor sensitivity can be adjusted. Default is level 7. Lowering the level decreases the detection range.

Adjustment Steps:

1. Turn off power, then restart the smart toilet.
2. Within 30 seconds, press and hold the Feminine Wash button for 5 seconds to enter radar adjustment mode.
3. Press the Rear or Front button to adjust sensitivity.
4. Press the Stop button to confirm.

Lid/Seat open

The toilet features an open lid and seat function activated by the foot sensor when a person approaches from the front. You can also use the remote control button.

Foot Sensor Open Lid and Seat:

• When unseated: Place foot near the sensor area. The lid opens.
• If the lid is up and seat is down, trigger again to open the seat.
• If both lid and seat are up, trigger again to close them and flush once (if last operation was flush, closing lid won't flush again).

Remote Control Open Lid and Seat:

• When unseated: Press the open lid and seat button for the sequence: "Lid opens → Seat opens → Seat closes → Lid opens."
• Press the close button to lower both seat and lid and flush once (if last operation was flush, closing lid won't flush again).
• If both are already down, the close button does nothing.
• This function is temporarily disabled when the toilet is in operation (e.g., washing, flushing).

Enema/Aperient

Provides an enema function for bowel relief using a single nozzle. Press the Enema button on the remote to activate. Water sprays from the nozzle. While seated, press the button to start; a "beep" indicates activation. Press "Stop" to end. Water pressure is fixed; nozzle position and temperature are adjustable.

Rear Wash

Features a rear wash function with a single nozzle. Press the Rear Wash button to activate back-and-forth washing. Press the nozzle position button to switch to fixed mode. The function lasts approximately 3 minutes and stops automatically. You can switch functions or press "Stop" to end early.

Feminine Wash

Provides gentle cleansing with a dedicated nozzle. Press the Feminine Wash button for back-and-forth cleansing. Press the nozzle position button to switch to fixed mode. The function stops automatically after approximately 90 seconds. You can switch functions or press "Stop" to end early.

Wash Water Pressure Adjustment

In rear or feminine wash mode, press the wash intensity buttons (+/-) to adjust water pressure. There are 4 levels.

Wash Nozzle Position Adjustment

In rear or feminine wash mode, press the nozzle position buttons (▲/V) to move the nozzle forward or backward. There are 5 cleaning positions.

Wash Water Temperature Adjustment

In rear or feminine wash mode, press the wash water temperature buttons (+/-) to adjust water temperature. There are 4 levels: room temperature, high, medium, and low.

Hot and Cold Massage

Press the Massage button on the remote. Water temperature alternates between hot and cold, following set temperature levels. If set to room temperature, it alternates between room temp and the set level.

Child Wash

Press and hold the Child Wash button to activate. This mode does not require the user to be seated and automatically adjusts nozzle position, water temperature, and water pressure.

Drying Function

Press the Drying/Self-Cleaning button to activate. Focuses on drying cleaned areas. Automatically stops after approximately 3 minutes. You can switch functions or press "Stop" to end early.

Drying Temperature Adjustment

Press the Air Temperature button. Adjust to desired air drying temperature. There are 4 levels: room temperature, high, medium, and low.

Seat Temperature Adjustment

Press the Seat Temperature button. Adjust to desired seat temperature. There are 4 levels: room temperature, high, medium, and low.

Night Light

Press and hold the Night Light button to turn on/off. Provides convenient nighttime illumination.

Nozzle Self-Cleaning

Press and hold the Drying/Self-Cleaning button. Water flows through the nozzle. Effective only when no one is seated. Cycle lasts approximately 90 seconds. Press "Stop" to end.

Power Button

Press and hold the Power/Stop button to shut down the main unit system.

Remote Flush

Press the Flush button on the remote for a single flush. If washing is active, it will stop.

Manual Flush

When not seated, press the Rear Wash or Feminine Wash button on the main unit for a manual flush. If washing is active, it will stop.

Foot-Sensor Flush

For men's convenience during urination. Lightly tap the foot sensor (when the seat is raised) to activate flush. Uses capacitive sensing technology.

Enema / Aperient

Includes an enema function for bowel relief. Press the Enema button on the remote to activate. Water sprays from the single nozzle. While seated, press to start; a "beep" indicates activation. Press "Stop" to end. Water pressure is fixed; nozzle position and temperature are adjustable.

Power-Outage Flushing

In case of a power outage, press and hold the Feminine Wash button on the main unit for 3 seconds to activate.

Smart Seat Temperature

The main unit defaults to smart seat temperature mode, adjusting automatically to seasonal temperatures. Press the Seat Temperature button to cancel smart mode. Press and hold for 3 seconds to re-enter smart mode or restore after a power reset.

Foam Shield

• Manual Activation: Press the Foam Shield button on the remote to activate foam generation once.
• Automatic Activation: Foam is automatically generated once seated. Press and hold the Foam Shield button for 3 seconds to turn automatic function on/off.

Blue Toilet Cleaner Tablets Function

• Activated Mode: During the refill stage of each flushing cycle, blue cleaning liquid is mixed with water.
• Automatic Blue Cleaner Setting: Press and hold the Air Temperature button for 5 seconds. Two "beep" sounds indicate the function is turned on/off.

Cleaning and Maintenance

Clean and Maintain the Power Plug

Clean the power plug regularly. Remove from outlet and wipe with a dry cloth. Dust accumulation may cause fire.

Clean and Maintain the Main Unit of the Smart Toilet

Wipe the surface with a soft, wet cloth. Pull the power plug out before cleaning. For stubborn stains, use a soft, wet cloth with neutral kitchen detergent.

Clean and Maintain the Ceramic Part of the Smart Toilet

Use a neutral toilet cleaner on a soft brush or sponge. Rinse with tap water. Do not use detergents with chlorine or acids, or brushes with abrasive materials.

Clean and Maintain the Nozzle

In normal operation, press the Drying/Self-Cleaning button on the remote. The nozzle extends and auto-cleans. You can use a toothbrush simultaneously. Do not stretch the nozzle by force.

Detachable nozzle model cleaning method:

1. Press the self-cleaning button on the remote to extend the nozzle.
2. Pull out the front nozzle by hand.
3. Use a toothbrush to clean the nozzle.

Clean and Maintain the Water Inlet Filter in the T-Valve

1. Turn off the shut-off valve to stop water supply.
2. Remove the lock and filter from the T-valve.
3. Clean the filter with a brush or running water.
4. Reinstall the filter securely, ensuring the lock is in place.
5. Turn on the supply valve and check for leaks.

When not in use for a long time

Drain all water from the smart toilet and use a dry towel to absorb remaining water to prevent deterioration and freezing. Turn off power and remove the remote control battery.

1. Close the shut-off valve and stop water supply.
2. Unplug the power plug from the outlet.
3. Remove the water hose from the shut-off valve, drain it, and reinstall.

When using again, open the shut-off valve, plug in the power, and turn on.

Troubleshooting

Some malfunctions can be resolved by simple operations. Please confirm the following before authorizing professional repair:

Warranty

Warranty Period:

One year from the date of purchase.

What's Covered:

This product is warranted to be free of defects in materials and workmanship for one year. During the warranty period, free replacement parts will be provided for defects or malfunctions.

Note: This warranty is limited and does not cover damage caused by improper use or maintenance.

Caution

Prohibited Cleaners:

• Do not use cleaners containing abrasive materials, ammonia, bleach, acids, waxes, alcohol, solvents, or any other products not recommended for chrome finishes. Doing so may damage the product and void the warranty.

Proper Use and Maintenance:

• Ensure the product is used and maintained according to the user manual. Failure to follow these instructions may result in damage not covered under warranty.

Function List

The following table lists the functions available for the ZYC8A model:

• Indicates this product contains the function; blank indicates no function. Remarks: The function of different items may be different from the above list; detailed function is in accordance with the actual product.

Product Specification

• Rated Voltage: 120V~60Hz
• Rated Power: 1200W (water intake temperature of 59°F [15°C], water pressure of 0.24MPa, maximum level for front cleansing)
• Power Cord Length: 1.2M
• Water Pressure Range: 0.15MPa (dynamic pressure) ~ 0.75MPa (static pressure)
• Flush Water Consumption: 1.03 gallons per flush (Less than 4.0L)
• Cleansing Water Consumption: Less than 13.5oz/min (Less than 0.4L/min)
• Energy Consumption per Unit Cycle: Less than 0.03kWh
• Overall Unit Waterproof: IPX4
• Product Dimensions (LWH): 27.83*15.31*17.95 inches (707*389*456mm)
• Product Weight: 101.4 lbs (46KG)
• Bidet Function:
  • Water Heating Method: Instantaneous Heating
  • Water Pressure: 4-level adjustable
  • Water Temperature: Room Temperature, Level 1 (95°F), Level 2 (98.6°F), Level 3 (102.2°F) Sensor, Temperature Switch
  • Maximum Power for Water Heating: 1600W
  • Safety Device: Temperature Sensor, Temperature Switch
• Heated Seat Ring:
  • Heating Power: 40W
  • Seat Ring Temperature: Room Temperature, Level 1 (95°F), Level 2 (98.6°F), Level 3 (102.2°F) Sensor, Temperature Switch
  • Safety Device: Temperature Sensor, Thermal Fuse
• Drying Function:
  • Wind Speed: Greater than 8.9 mph (Greater than 4m/s)
  • Heating Power: 270W
  • Wind Temperature: Room Temperature, Level 1 (95°F), Level 2 (113°F), Level 3 (131°F)
  • Safety Device: Resettable Thermal Protector, Temperature Fuse

Notes: The rated power and performance specifications are based on the following test conditions: Ambient Temperature: 73.4°F ± 3.6°F; Inlet Water Pressure: 0.24MPa ± 0.02MPa; Inlet Water Temperature: 59°F ± 0.9°F. Average power consumption for cleansing and drying functions was calculated over a 1-minute usage cycle.

Acceptance Record

After the installation is complete, please test run the toilet and fill out the record sheet with the results:

Remark:

Retailer: _________________________ Installation personnel: _________________________ Acceptance tester: _________________________ Date: _________________________