Bazyths Smart Toilet - Instruction Manual

Automatic Opening/Closing of Lid & Seat

The toilet lid automatically opens when a user approaches. The seat and lid automatically close 2 minutes after the user leaves the sensor range. This function can be toggled on/off using the Dryer button on the remote control.

Foot Sensor for Lid/Seat Control

Opens or closes the toilet lid or toilet seat when the user moves their foot near the sensor.

Rear Wash

Water is released from a single nozzle for powerful cleaning. The cycle lasts 90 seconds and can be stopped by pressing the side knob or the "Stop" button on the remote control.

Feminine Wash / Front Wash

Designed for gentle cleaning for female use. The 90-second cleaning cycle can be stopped by pressing the side knob or the "Stop" button on the remote control.

Warm Air Dryer

Offers 4 temperature settings (room temperature, high, medium, low) for drying. Can be activated by turning the side knob twice in the same direction while seated. The drying cycle lasts 3 minutes.

One-Twist Quick Mode (Wash + Flush + Dry)

Activates a wash, flush, and dry sequence automatically. Each cleaning cycle is 90 seconds, followed by auto-flush and a 3-minute drying cycle. The drying phase can be accessed directly by turning the knob again during the wash cycle.

Remote Control

All functions are accessible via the wireless remote control.

Rear Wash with Moving Nozzle

The nozzle moves back and forth for a wider cleaning area. Toggle between moving and non-moving cleaning by pressing the rear wash button again on the remote.

Feminine Wash with Moving Nozzle

The nozzle moves back and forth for gentle cleaning over a wider area.

Hot and Cold Massage

The nozzle alternates between warm and cool water for a massaging effect. Activate by pressing and holding the feminine wash button for 5 seconds. It alternates between 10 seconds of cool water and 5 seconds of warm water.

Cleansing Strength Adjustment

Adjust cleansing strength/water pressure according to preference.

Cleansing Position Adjustment

Adjust the cleansing position by moving the nozzle back and forth.

Cleansing Water Temperature Adjustment

Offers 4 levels of cleansing water temperature: normal, high, medium, and low.

Seat Sensor

Activates functions when the user is seated.

Toilet Seat Temperature Adjustment

Heated seat with 4 levels of temperature adjustment: normal, high, medium, and low.

Auto Off-Seat Flush

Automatically flushes after the user stands up from the toilet seat.

Foot Sensor Flush

Flush by moving your foot near the sensor.

Flush by Remote Control

Flush by pressing the flush button on the remote control.

Flush by Side Knob

Flush by pressing the side knob on the smart toilet.

Night Light

Provides gentle illumination for navigating the bathroom at night.

Nozzle Cleaning

Initiates a self-cleaning mode for the nozzle by pressing and holding the corresponding button on the remote control when the seat is unoccupied.

Nozzle Auto Cleaning

The nozzle automatically cleans itself before and after each use.

Power Outage Flush

Utilizes the backup battery box to enable flushing during a power outage.

Children's Mode Features

• One-Button Cleaning: Activates a child-friendly automatic cleaning cycle.
• Preset Seat Temperature: Child seat maintains a fixed 86°F for comfort and safety.
• Gentle Water Temperature: Default 95°F, adjustable up to 100°F.
• Low Water Pressure: Set to the lowest level for a gentle wash.
• Soft Warm Air Drying: Operates at a preset 95°F.
• Safety Lock: Disables foot sensor, remote lid opening, and seat flipping functions in Children's Mode to prevent accidental operation.
• Automatic Exit & Flush: Exiting Children's Mode triggers an automatic flush.

1. Confirmation of Installation Environment

Ensure bathroom wall and floor tiles are completed. Confirm sewage pipes, water pipes, and electrical circuits are reserved as shown in the figure. The toilet rough-in is 300mm (11.81in). Water inlet pressure range: 0.15Mpa (dynamic) - 0.75Mpa (static). Water inlet temperature: 4°C-35°C (39.2°F-95°F).

Diagram Description: Shows dimensions for wall clearance, water inlet, and drain outlet relative to the toilet's position.

2. Assembly of Dedicated Shut-off Valve

Install the provided shut-off valve. If your existing shut-off valve has a 3/8" outlet, use the Spare Adapter (refer to page 3) to connect to the smart toilet without replacing the valve.

Diagram Description: Illustrates the shut-off valve and its connection points.

3. Installation and Fixation of the Toilet

The included flange is designed for a 4-inch drain pipe; purchase a compatible flange locally for a 3-inch pipe. Install the flange approximately 1/4 inch (0.6 cm) above the finished floor to prevent leaks.

1. Align the "flange-ABS" on the ground drain outlet, orient the "flange-ABS" arrow vertically to the wall, and mark drilling positions. Drill four holes.
2. Install "Flexible Flange Seal Strip" at the bottom of "flange-ABS".
3. Insert "expansion plastic sleeve - small" into the small hole. Align holes and install "flange-ABS" and "sealing wax ring - thin". Secure with "round head self tapping screw-5×36mm".
4. Insert "bolt-8×43mm" into the "flange-ABS" slot. Adjust "bolt-8 x 43mm" so the center line of the bolts is perpendicular to the arrow on the flange body.
5. Align the "Wax Ring Gasket" with the drain outlet and install on the "flange-ABS". Insert L-shaped plastic fixed blocks and gaskets into "bolt-7x43mm". Install "large washer-8x24x1.8mm" and "nut 5/16".
6. Align the intelligent toilet's drain outlet with the flange center.
7. Install "T-shaped pad" on small holes on both sides of the ceramic pan and secure with "flat head self tapping screw-5×75mm". (Use 90mm backup screws if shorter screws are needed).
8. Cover "T-shaped pads" with "decorative caps".

Caulk the bottom of the toilet with silicone sealant.

Diagram Description: Shows steps for installing the flange, seal strip, bolts, wax ring, and securing the toilet.

4. Connection of the Water Inlet Hose

Connect the inlet hose with the shut-off valve & T-valve using a wrench. After installation, turn on the shut-off valve to check for leaks.

Diagram Description: Illustrates connecting the inlet hose for cleansing and flushing water to the shut-off valve and T-valve.

How to Use

When Sitting on the Seat

• Upon hearing the "beep" sound, functions will start. The nozzle cleans itself automatically.
• Start Rear Cleansing or Front Cleansing: Use the remote control.
• Adjust Cleansing Position and Water Pressure: Use the remote control.
• Start Drying: Use the remote control.
• Stop Function: Press the "Stop" button on the remote control (rear cleansing, front cleansing, or drying).

When Standing Up from the Seat

• The toilet will auto-flush once.

Function Setting and Adjustment

Radar Sensor Function

When a user approaches within 30cm, the lid will auto-open. Long press the "Close the lid" button on the remote to toggle this function.

Lid/Seat Open

The product features a clamshell turning circle. Foot induction triggers the flip. Press the flip circle function key on the remote to turn over the seat cover and seat ring.

Foot Clamshell Cover: Behavior varies based on user presence and seat position (low/high), triggering seat cover/child seat up, adult seat up, or closed seat cover ring with flush.

Remote Mustache Cover Loop: Pressing the remote control flip cap key cycles through seat cover + child seat up, adult seat up, adult seat down, and seat cap down with flush.

Flip circle functions pause during washing, women washing, or flushing.

Diagram Description: Shows three stages: 1. User approaches, lid/seat automatically turn over. 2. Adult seat turns up. 3. Automatic close cover and flush.

Panel Instruction

Remote Control Panel

The product is designed primarily for remote control operation, with main unit panel operation as a supplement.

Diagram Description: Shows the front and back of the remote control panel with various buttons labeled for functions like water pressure, nozzle position, cleaning modes, drying, seat temperature, night light, etc.

Child Remote Control Panel

Features buttons for Child Mode, One-Touch Automatic, Seat Temperature for Child, and Flushing.

Diagram Description: Shows icons for Child Mode, One-Touch Automatic, Seat Temperature for Child, and Flushing.

Remote Control Matching Method

To pair the remote: Turn to rear cleansing direction for 3 seconds (short sound, screen flashes). Turn to front cleansing direction for 3 seconds (enter "di - di - di" mode). If pairing fails within 10 seconds, the screen flashes. Successful pairing restores the screen to normal with a long sound.

Function Side Knob (with Light Ring) on the Main Unit

• Switch by pressing the knob: Flush/Stop.
• Non-working condition: Press knob down vertically to flush once. Hold down for 4 seconds to turn the product on or off.
• Seated position: Rotate clockwise for rear cleansing; rotate counterclockwise for front/female cleansing. Press down vertically to stop the current function.
• Drying: Rotate the knob in the same direction again during rear or front cleansing to activate drying.
• One-Twist Quick Mode: Activates wash, flush, and dry sequence. Can skip to drying phase.

Display Screen on the Main Unit

The display shows:

• Power indicator: Lights up when the main unit is on.
• Temperature level: Displays set temperature.
• Air temperature icon: Indicates set air dryer temperature.
• Seat temperature icon: Indicates set toilet seat temperature.
• Cleansing water temperature icon: Indicates set cleansing water temperature.

The screen cycles through water, seat, and air dryer temperatures every 30 seconds. The screen turns off automatically about 30 seconds after the user leaves the sensor area.

Children's Mode

Provides a one-key automatic operation for children.

• Child Mode Activation: Short press the child mode button on the remote or side button to open child mode. Flip/flip ring until the child seat is closed.
• Exiting Child Mode: Short press the child mode button again to exit and flush. In child mode, the power lamp flashes, and remote/foot sensor functions are invalid.
• One-button cleaning for children: Activates cleaning with specific settings (95°F water temp, adjustable up to 100°F; lowest cleaning water pressure; 95°F wind temperature).

Rear Wash

Provides rear cleaning using a single hole nozzle. Can activate moving cleaning (nozzle moves back and forth) by pressing the button again. Pressing again stops moving cleaning. The function turns off automatically after 90 seconds. Nozzle auto-cleans before and after use.

Feminine Wash

Provides front cleaning with a feminine applicator for gentle cleaning. Can activate moving cleaning (nozzle moves back and forth) by pressing the button again. The function turns off automatically after 90 seconds. Nozzle auto-cleans before and after use.

Wash Water Pressure Adjustment

Press the button to adjust water pressure strength. 4 levels available.

Wash Nozzle Position Adjustment

Press the "Nozzle" button to move the nozzle back and forth. 5 levels available.

Wash Water Temperature Adjustment

Press the button to adjust water temperature. 4 levels available: normal, high, medium, low.

Hot and Cold Massage

Long press the remote control "woman wash" function key to activate alternating cold and warm water massage. It alternates between 10 seconds of cool water and 5 seconds of warm water.

Drying Function

Press the button on the remote to dry. The function automatically turns off after 3 minutes. Can be stopped manually.

Drying Temperature Adjustment

Press the button to enter dryer temperature settings. 4 levels available: normal, high, medium, low.

Child Seat Ring Temperature Regulation

Press the temperature function key on the child remote control to toggle child seat ring temperature on/off. Adjustable in 2 gears: normal and low.

Seat Temperature Adjustment

Press the seat temperature function key on the remote to adjust seat temperature. 4 gears available: room temperature, high, medium, low.

Night Light

Long press the remote control wind temperature function key to enable or disable the lighting function.

Nozzle Self-Cleaning

Press the self-cleaning function key on the remote. Water flows from the nozzle for cleaning. Head cleaning is effective only when the user is not seated. Cleaning time is about 60 seconds. Press the button to end.

Power Button

Long press the host knob for 4 seconds to turn the system on or off.

Remote Flush

Press the flushing button to flush the toilet once. Stops cleaning functions.

Manual Flush

Press the flushing rotary knob vertically to flush. Available even when the host system is shut down. Stops cleaning functions.

Foot-Sensor Flush

Designed for men to urinate. Uses capacitive induction technology to flush when the foot is detected.

Power-Outage Flushing

In case of power outage, long press the side knob for 3 seconds to wake up the internal power supply, then short press to activate power outage flushing.

Clean and Maintain the Power Plug

Regularly clean the power plug. Remove it from the outlet and wipe with a dry cloth. Dust accumulation can cause fire.

Clean and Maintain the Main Unit of the Smart Toilet

Wipe the surface with a soft, wet cloth. Ensure the power is disconnected before cleaning. For stubborn stains, use a soft cloth with neutral kitchen detergent.

Clean and Maintain the Ceramic Part of the Smart Toilet

Use a neutral toilet cleaner and a soft brush or sponge. Rinse with tap water. Do not use chlorine-based detergents, disinfectants, or abrasive brushes.

Diagram Description: Shows a bottle of toilet cleaner and a brush.

Clean and Maintain the Nozzle

When the smart toilet is on, press the remote control button to activate nozzle cleaning. The nozzle extends and cleans itself with water. A toothbrush can be used for cleaning. Do not forcefully stretch the nozzle. The nozzle can be removed and cleaned separately.

Diagram Description: Illustrates detachable nozzle cleaning: 1. Extend nozzle. 2. Pull out front nozzle. 3. Clean with toothbrush.

Clean and Maintain the Water Inlet Filter in the T-Valve

• Turn off the shut-off valve to stop water supply.
• Remove the lock and filter from the T-valve.
• Clean the filter with a brush or running water.
• Reinstall the filter securely, ensuring the lock is in place.
• Once reinstalled, turn on the supply valve and check for leaks.

When Not in Use for a Long Time

Drain all water from the smart toilet and water inlet hose. Use a dry towel to absorb remaining water to prevent deterioration and freezing. Turn off the power and remove the battery from the remote control.

1. Close the shut-off valve.
2. Unplug the power plug.
3. Remove the water hose from the shut-off valve, drain it, and reinstall it.