Vortice Accessory Wiring Diagrams
Instruction booklet
EEC Single Phase - Direct (Without Regulation)
1- 220V motor supply through L & N
2- Jumper between 2 & 3 on the control terminals (Vsp y Vcc)
Wiring Diagram 1:
- Terminal 1: GND (Blue)
- Terminal 2: Vsp (Yellow) - 0-10V/PWM
- Terminal 3: Vcc (Red) - DC 10V
- Terminal 4: FG (White) - 1 Pulse/R
Wiring Diagram 2:
- Terminal 1: GND (Blue)
- Terminal 2: Vsp (Yellow) - 0-10V/PWM
- Terminal 3: Vcc (Red) - DC 10V
- Terminal 4: FG (White) - 12 Pulse/R
Power Supply Connections:
- L (Brown) - AC 220V-50/60 Hz
- N (Blue) - AC 220V-50/60 Hz
- Pe (Yellow-Green) - Ground Symbol ⏚
EEC Three Phase - Direct (Without Regulation)
1- 380V motor supply through L1, L2 y L3
2- Jumper between terminals 2 and 3 of the control (Vsp and Vcc)
Wiring Diagram 1:
- Terminal 1: GND (Blue)
- Terminal 2: Vsp (Yellow) - 0-10V/PWM
- Terminal 3: Vcc (Red) - DC 10V
- Terminal 4: FG (White) - 1 Pulse/R
Wiring Diagram 2:
- Terminal 1: GND (Blue)
- Terminal 2: Vsp (Yellow) - 0-10V/PWM
- Terminal 3: Vcc (Red) - DC 10V
- Terminal 4: FG (White) - 12 Pulse/R
Power Supply Connections:
- L1 (Black) - AC380V/50Hz
- L2 (Black) - AC380V/50Hz
- L3 (Black) - AC380V/50Hz
- Pe (Yellow-Green) - Ground Symbol ⏚
PMR + EEC Motor (Single Phase)
1- 220V Supply motor in N and L through the switch
2- Power the REGC with 10V. Connect GND with GND and Vcc (10V) with Vcc
3- Connect terminal 2 (Vsp) of the motor with Output (0-10V) of the PMR (control signal 0-10V)
Motor Connections:
- Terminal L (Brown) - AC 220V-50/60 Hz
- Terminal N (Blue) - AC 220V-50/60 Hz
- Terminal Pe (Yellow-Green) - Ground Symbol ⏚
Potentiometer Connections:
- Blue/Azul: GND - 0V
- Yellow/Amarillo: Output → 0-10V
- Red/Rojo: Vcc - 10V
Ventilador EEC Connections:
- Terminal 1: GND (Blue)
- Terminal 2: Vsp (Yellow) - 0-10V/PWM
- Terminal 3: Vcc (Red) - DC 10V
- Terminal 4: FG (White) - 1 Pulse/R
PMR + EEC Motor (Three Phase)
1- 380V Supply motor in L1, L2 and L through the switch
2- Power the REGC with 10V. Connect GND with GND and Vcc (10V) with Vcc
3- Connect terminal 2 (Vsp) of the motor with Output (0-10V) of the PMR (control signal 0-10V)
Motor Connections:
- Terminal L1 (Black) - AC380V/50Hz
- Terminal L2 (Black) - AC380V/50Hz
- Terminal L3 (Black) - AC380V/50Hz
- Terminal Pe (Yellow-Green) - Ground Symbol ⏚
Potentiometer Connections:
- Blue/Azul: GND - 0V
- Black/Negro: Output → 0-10V
- Red/Rojo: Vcc - 10V
Ventilador EEC Connections:
- Terminal 1: GND (Blue)
- Terminal 2: Vsp (Yellow) - 0-10V/PWM
- Terminal 3: Vcc (Red) - DC 10V
- Terminal 4: FG (White) - 1 Pulse/R
POT + EEC Fan (Single Phase)
1- 220V Supply motor through N and L
2- Power the POT with 10V. Connect GND with GND and Us with Vcc
3- Connect terminal 2 (Vsp) of the motor with +OUT of the POT (control signal 0-10V)
Ventilador ES Connections:
- Terminal 1: GND (Blue)
- Terminal 2: Vsp (Yellow) - 0-10V/PWM
- Terminal 3: Vcc (Red) - DC 10V
- Terminal 4: FG (White) - 1 Pulse/R
Power Supply Connections:
- L (Brown) - AC 220V-50/60 Hz
- N (Blue) - AC 220V-50/60 Hz
- Pe (Yellow-Green) - Ground Symbol ⏚
POT + EEC Fan (Three Phase)
1- 380V Supply motor through L1, L2 and L3
2- Power the POT with 10V. Connect GND with GND and Us with Vcc
3- Connect terminal 2 (Vsp) of the motor with +OUT of the POT (control signal 0-10V)
Ventilador ES Connections:
- Terminal 1: GND (Blue)
- Terminal 2: Vsp (Yellow) - 0-10V/PWM
- Terminal 3: Vcc (Red) - DC 10V
- Terminal 4: FG (White) - 12 Pulse/R
Power Supply Connections:
- L1 (Black) - AC380V/50Hz
- L2 (Black) - AC380V/50Hz
- L3 (Black) - AC380V/50Hz
- Pe (Yellow-Green) - Ground Symbol ⏚
