About This Manual
This document is protected by copyright by DJI with all rights reserved. Unless otherwise approved by DJI, you are not qualified to use or allow others to use the document or any part of it by reproducing, transferring, or selling it. Users shall only refer to this document and its contents as instructions for using DJI products. The document shall not be used for other purposes.
Search for keywords: Search for keywords like 'battery' and 'installation' to find a topic. If using Adobe Acrobat Reader, press CTRL+F on Windows or Command+F on Mac to start a search.
Navigate to a topic: View a complete list of topics in the table of contents. Click a topic to navigate to that section.
Print this document: This document supports high-resolution printing.
How to Use This User Manual
DJI Power 1000 and DJI Power 500 have similar functions and operation. Unless specified otherwise, descriptions in this document use DJI Power 1000 as an example and apply to both products.
Explanation
- ⚠️ Important
- ? Tips and Advice
Read Before Use
DJI™ provides users with tutorial videos and the following documents:
- Safety Guidelines
- Quick Start Guide
- User Manual
It is recommended to watch all tutorial videos and read the disclaimer and safe use guidelines before using the product for the first time. Prepare for your first use by watching the quick start guide and this user manual for more information.
Tutorial Videos
Go to the address below or scan the QR code to watch the tutorial videos, which show how to use the product safely:
- DJI Power 1000: https://s.dji.com/guide67 [QR Code]
- DJI Power 500: https://s.dji.com/guide69 [QR Code]
Download DJI Assistant 2
Download DJI ASSISTANT™ 2 (Power Series) at: https://www.dji.com/power-1000/downloads or https://www.dji.com/power-500/downloads
Introduction
DJI Power 1000 is a portable power station with a capacity of 1024 Wh, weighing approx. 13 kg, and supporting a maximum output of 2200 W. DJI Power 500 is a portable power station with a capacity of 512 Wh, weighing approx. 7.3 kg, and supporting a maximum output of 1000 W. The power stations support fast charging and standard charging modes for AC power charging. In fast charging mode, the power station can be charged from 0% to 80% in approx. 50 minutes, and from 0% to 100% in approx. 70 minutes. [1] In standard charging mode, the charging speed is reduced, and the noise is lower, which is suitable for charging overnight. Charging in standard mode can extend battery life. The power station can be charged from 0% to 100% in approx. two hours. The power stations feature SDC/SDC Lite ports and support charging DJI intelligent flight batteries and other devices, as well as providing power supply. [1] Test performed at room temperature 25 °C (77 °F) and in good ventilation conditions.
DJI Power 1000
Diagram: DJI Power 1000 unit with numbered features: 1. Power button (on/off), 2. AC output port, 3. Screen, 4. AC output indicators, 5. AC output button, 6. AC input port, 7. Charging mode switch, 8. SDC Lite port, 9. USB-A ports, 10. USB-C ports, 11. Vents, 12. SDC port, 13. Vent, 14. 1/4" thread hole.
Note: Illustrations in the user manual may differ from the actual product, depending on the country or region. Refer to the actual product.
DJI Power 500
Diagram: DJI Power 500 unit with numbered features: 1. Power button (on/off), 2. Screen, 3. AC output port, 4. AC output indicators, 5. AC output button, 6. AC input port, 7. Charging mode switch, 8. SDC Lite port, 9. USB-A ports, 10. USB-C ports, 11. Vents.
Screen
Diagram: Power station screen display showing: 1. Current battery level, 2. Remaining usage time (output) or charging time (input), 3. Battery level indicator line, 4. System warnings. Other indicators: [Wi-Fi symbol], [Battery status], [Output/Input mode], [88Hz frequency], [Voltage display], [Percentage display].
- Displays the current battery level of the power station.
- Displays remaining usage time when the power station is charging external devices. Displays remaining time required to fully charge the power station from the current battery level when the power station is being charged.
- Battery level line: The battery level line flashes sequentially when the power station is being charged. The last grid on the battery level line flashes when the power station is charging external devices.
- System warnings.
Screen Error Codes and Symbols
ERRBB: Error Code
⚠️ Temperature Error: When the temperature is abnormal in Fast Charging mode, the temperature icon on the screen flashes slowly. Actual charging power may be reduced to preserve battery life and safety. The icon will light up constantly if the temperature is too high or too low. Wait for the temperature to return to normal.
OVERLOAD: Overload Warning
Go to https://s.dji.com/DJI-Power to learn more about warning details and troubleshooting.
- 5. [AC charging in fast mode]
- 6. [AC charging in standard mode]
- 7. [USB-A port]
- 8. [USB-C port]
- 9. 88Hz: [AC output frequency]
- 10. SDC/SDC Lite port: [Charging station or external devices via SDC/SDC Lite port], [Voltage display for SDC/SDC Lite port], [% battery level for intelligent flight battery charging via SDC/SDC Lite port].
- 11. Input power.
- 12. Uninterruptible Power Supply (UPS): If the power station is connected to an AC outlet and using AC power simultaneously, UPS is activated by default. This function is unavailable in some regions. Refer to local laws and regulations for more information.
- 13. Output power.
Powering On/Off
1. Power On/Off: Press and hold the power button for at least two seconds. The screen will automatically turn on after being powered on.
2. Turn Display Screen On/Off: When the power station is powered on, press the power button once.
Diagram: Power button with "ON/OFF" label and a timer icon showing "2s". Another button illustration with "ON/OFF" and "x1".
Charging External Devices
AC Output
The power station has two AC output ports. Connect the external device to an AC output port and press the AC output button for power supply.
Diagram: DJI Power 1000 and DJI Power 500 with AC output ports shown. An illustration shows a device (kettle) connected to the AC port with a label "AC x1".
The power station features automatic AC power off and automatic power saving.
- Automatic AC Shutoff: Press the AC output button once to activate AC output, and the AC output indicator will flash slowly. AC output will automatically shut off to save power if the power station is not charging any device via the AC output ports within half an hour.
- Continuous AC Output: Press and hold the AC output button to activate AC output, the AC output indicator will show a continuous light, and the AC output will not automatically shut off. This can provide continuous AC power supply to an external device that operates periodically, such as a refrigerator.
- Automatic Shutoff at Low Output Power: When AC output is deactivated, the power station will automatically shut off if it is not charging any device within one hour.
When recharging with AC power at different frequencies, the power station will automatically switch to the same frequency as the input power. To manually switch the AC output frequency, disconnect the power station from the AC outlet when AC output is activated, then press and hold the AC output button for 10 seconds.
• The internal electronic components have a waterproof coating. A slight odor may occur when using high power. The odor will disappear naturally with daily use.
USB Output
The power station has two USB-A ports and two USB-C ports. Connect the external device to the USB-A or USB-C ports for power supply.
Diagram: DJI Power 1000 unit showing USB-A and USB-C ports. Illustrations of a laptop, smartphone, and camera connected to these ports.
Fast Charging DJI Batteries
DJI Power 1000 has an SDC port and an SDC Lite port, and DJI Power 500 has an SDC Lite port. The power station can fast charge a supported DJI intelligent flight battery using an SDC fast charging cable (sold separately).
Diagram: DJI Power 1000 unit showing SDC and SDC Lite ports. Cables connecting to DJI Matrice 30 series, DJI Air 3, DJI Mavic 3 series, and DJI Inspire 3 batteries. An icon shows a battery with a lightning bolt.
Other SDC Output
The power station can also be used with other SDC cables (sold separately) to charge various devices via the SDC/SDC Lite port.
Diagram: DJI Power 1000 unit. Two cable types shown: "Plugg til billader" (Plug for car charger) and "XT60".
DJI Power SDC to Car Charger Plug Power Cable (12 V)
The power station can charge vehicle-powered devices such as a car refrigerator using this cable.
• Ensure the external device is within the cable's output specifications (voltage 13.6 V, current 10 A, power 136 W).
DJI Power SDC to XT60 Power Cable (12 V)
The power station can provide 12V DC input for devices with an XT60 port using this cable.
• DO NOT connect directly to a lithium battery with an XT60 port when using the DJI Power SDC to XT60 power cable. Ensure to connect the power station to a balanced charger first.
Charging the Station
AC Charging
The power station has modes for fast charging and standard charging for AC power charging.
Fast Charging Mode: In fast charging mode, the charging power is higher. It takes approx. 50 minutes to charge the power station to 80%, and approx. 70 minutes to 100%.
Standard Charging Mode: In standard charging mode, the charging power is lower and the operating noise is lower, which is suitable for charging overnight. Charging in standard mode can extend battery life. It takes about two hours to charge the power station to 100%.
Take DJI Power 1000 as an example, follow the steps below for AC power charging:
- Open the port cover and connect the DJI Power 1000 to a power outlet using the AC power cable in the package.
- Switch the charging mode selector to set the charging mode to 1200W fast charging mode or 600W standard charging mode. For DJI Power 500, the charging mode can be set to 540W fast charging mode or 270W standard charging mode.
Diagram: Illustration showing connection to a 100-120 V AC or 220-240 V AC outlet. A second illustration shows the power station connected, with a switch indicating "1200 W" (fast) and "600 W" (standard).
- Disconnect from the AC power outlet when charging is complete.
- Standard charging mode is recommended for extended battery life.
- The power station provides a battery cell protection strategy. If the power station is charged in fast charging mode for five consecutive cycles, the power station will automatically switch to standard charging mode after the sixth fast charge for battery maintenance. The maintenance process lasts for approx. 20 minutes.
- When the temperature is abnormal in Fast Charging mode, the temperature error icon on the screen flashes slowly. Actual charging power may be reduced to preserve battery life and safety.
Solar Charging
The power station can be connected to solar panels using the DJI Power Solar Panel Adapter Module (MPPT) or the DJI Power Car Power Outlet to SDC Power Cable for solar charging. Both types of accessories are sold separately.
Take DJI Power 1000 as an example, follow the steps below for solar charging:
- Unfold the solar panel, support it with the stand, and adjust the panel so it faces the sunlight. Adjust the angle of the stand. It is recommended that the surface of the solar panel is perpendicular to the sunlight. Ensure the solar panel is not covered by obstacles.
- Connect the solar panel with an XT60 cable to the solar panel adapter module to begin charging.
Diagram: Illustration of unfolding a solar panel and positioning it towards the sun (90-degree angle indicated). Second illustration shows the power station connected via XT60 cable to a ZIGNES solar panel adapter module.
- Follow the instructions for using the solar panel. DO NOT mix solar panel types. Otherwise, the device may be damaged.
- Up to three solar panels can be connected to the adapter module and used in parallel (cannot be used in series). DJI Power 1000 can connect two solar panel adapter modules and up to six solar panels for solar charging. DJI Power 500 can connect to one solar panel adapter module and up to three solar panels for solar charging.
- The DJI Power Car Power Outlet to SDC Power Cable allows one solar panel to be connected for solar charging. The maximum current of the solar panels should be less than 10 A, and the output power should be less than 100 W.
- It is recommended to use DJI-authorized Zignes solar panels. If non-recommended solar panels are used, ensure that the solar panels meet all the following requirements to avoid damaging the solar panel adapter and the power station:
- a. The open-circuit voltage is less than 30 V.
- b. The maximum current for each solar panel used is less than 10 A.
- c. If more than one solar panel is used, the total power is less than 400 W.
- For DJI Power 500, the maximum input power is limited to 300 W when using the SDC Lite port for solar charging.
- Keep the power station away from direct sunlight when recharging it. Overheating may cause damage to the device.
- Prevent leaves and other objects from covering the surface of the solar panel. Placing the solar panel in a partially shaded area will affect charging efficiency and cause overcurrent, which may damage components.
- Dampen a soft cloth with clean water and wipe the surface to clean the solar panel.
Car Charging
The DJI Power Car Power Outlet to SDC Power Adapter can be used to connect a car power outlet to the SDC port (or SDC Lite port) on the power station for car charging.
Diagram: DJI Power 1000 unit connected via car charger adapter to a car's power outlet.
- Ensure the input voltage of the car's power outlet is within 12–30 V and the maximum input current is less than 8 A. Otherwise, it may lead to abnormal performance or even damage to the power station.
- Ensure the power adapter is properly connected to the car's power outlet and the car engine is started before charging.
USB-C Charging
DJI Power 500 can be charged using a USB Power Delivery charger via the USB-C port for a maximum charging current of 100 W. It also supports simultaneous power input, where two USB-C ports can be used for charging with a maximum power of 200 W.
Uninterruptible Power Supply (UPS)
The power station supports Uninterruptible Power Supply (UPS). Connect the power station to an AC outlet, and connect an external device such as a computer to the power station. Press the AC button once, and [UPS icon] will be displayed on the screen. In this case, the AC outlet powers both the power station and the connected device. Note that UPS is activated by default.
In case of a sudden power outage, the power station can automatically switch to the battery-powered supply within 20 ms, allowing the connected device to remain in normal operation.
Diagram: Illustration showing the power station connected to an AC outlet (1) and a computer (2). The AC button is shown with "AC x1".
- The power station only supports the basic UPS function and does not support 0 ms switching. DO NOT connect the power station to devices that require 0 ms UPS, such as medical equipment, data servers, or workstations storing critical data. Otherwise, it may lead to malfunction or data loss.
- This function is unavailable in some regions. Refer to local laws and regulations for more information.
DJI Power 1000 Extensions
1/4" Thread Hole
DJI Power 1000 has two 1/4" threaded holes, allowing users to mount the DJI Power Solar Panel Adapter Module (MPPT) to the power station as follows:
Mount one adapter module to the power station by following Figure A.
Align the mounting holes at the bottom of the brackets with each other, and mount two adapter modules to the power station by following Figure B.
• Users can also mount devices with 1/4" screws to the power station.
Diagram: Figure A shows mounting one adapter module using screws. Figure B shows mounting two adapter modules using screws.
Protective Carrying Case
DJI Power 1000 can be used with the protective carrying case. The case can protect the power station from scratches and dust, and make it more convenient to carry the power station.
Open the front of the case for connecting external devices to the power station, and the back of the case is for storing cables and accessories.
When using the DJI Power 1000 with the protective carrying case, be sure to open the zippers on both sides of the case to avoid blocking the vents, which may cause overheating.
Diagram: Illustration showing the DJI Power 1000 inside its carrying case, with zippers indicated.
Addendum
Firmware Update
The firmware versions of DJI Power 1000 and DJI Power 500 can be updated using DJI Assistant 2 (Power Series). Ensure your computer is connected to the internet during the firmware update. Follow the instructions below to ensure a successful firmware update:
- Turn off the device, press and hold the AC button and the power button simultaneously until LOAD is displayed on the screen.
Diagram: Illustration showing the power station being turned off.
- Connect the device to an AC power outlet if you are updating the firmware for DJI Power 1000 with a rated voltage of 100 V or 120 V. Skip this step if you are updating the firmware for other power station models.
Diagram: Illustration showing the power station connected to a laptop via USB.
- Start DJI Assistant 2, select the product, and click the firmware update button on the left side.
- Select the firmware version, read the prompts in DJI Assistant 2 carefully, and click update. The firmware will be downloaded and uploaded to the device automatically.
- Firmware updates automatically, and the screen will display the update progress. Wait for the download and upload to complete. The device will restart automatically after the firmware update is complete.
- DO NOT turn off the device or disconnect the device from the computer during the firmware update.
- DO NOT connect other devices to the power station or computer during the firmware update.
- If the firmware update fails, try again by pressing and holding the power button for 10 seconds to restart the device, and then try again.
Troubleshooting
For error codes or screen prompts, click the QR code below or scan it to learn more about the error details and troubleshooting. Contact DJI Support if you have any problems.
Diagram: QR code with URL "https://s.dji.com/DJI-Power".
Maintenance
- Store the power station in a cool, dry place for extended periods, away from direct sunlight. Overheating may cause damage to the device.
- To prevent leaves and other objects from covering the solar panel surface. Placing the solar panel in a partially shaded area will affect charging efficiency and cause overcurrent, which may damage components.
- Dampen a soft cloth with clean water and wipe the surface to clean the solar panel.
- If the power station is used for a long time, it is recommended to charge it to 100% every 3 months to maintain battery health.
- When charging the power station, use the standard charging mode to extend battery life. If the power station is charged in fast charging mode for five consecutive cycles, it will automatically switch to standard charging mode after the sixth fast charge for battery maintenance. The maintenance process lasts for about 20 minutes.
- When the temperature is abnormal in Fast Charging mode, the temperature error icon on the screen flashes slowly. Actual charging power may be reduced to preserve battery life and safety.
- Clean the terminals with a dry cloth, and do not use alcohol or other flammable solvents.
Accessories (Sold Separately)
Unless otherwise specified, accessories are compatible with both DJI Power 1000 and DJI Power 500.
| Accessory | Description/Illustration |
|---|---|
| Zignes Solar Panel | Diagram: ZIGNES solar panel with connection cable. |
| DJI Power Solar Panel Adapter Module (MPPT) | Diagram: Adapter module with SDC input and multiple outputs. |
| DJI Power Car Outlet to SDC Power Cable (12V/24V) | Diagram: Cable with car power plug on one end and SDC connector on the other. |
| DJI Power SDC to Matrice 30 Series Fast Charging Cable | Diagram: Cable with SDC connector and Matrice 30 series battery connector. |
| DJI Power SDC to DJI Mavic 3 Series Fast Charging Cable | Diagram: Cable with SDC connector and Mavic 3 series battery connector. |
| DJI Power SDC to DJI Air 3 Fast Charging Cable | Diagram: Cable with SDC connector and Air 3 battery connector. |
| DJI Power SDC to DJI Inspire 3 Fast Charging Cable | Diagram: Cable with SDC connector and Inspire 3 battery connector. |
| DJI Power SDC to XT60 Power Cable (12 V) | Diagram: Cable with SDC connector and XT60 connector. |
| DJI Power SDC to Car Charger Plug Power Cable (12V) | Diagram: Cable with SDC connector and car charger plug. |
| DJI Power 1000 Protective Carrying Case (for DJI Power 1000 only) | Diagram: Carrying case for DJI Power 1000. |
Specifications
DJI Power 1000
| Category | Details |
|---|---|
| General | |
| Model | DYM1000L/DYM1000H |
| Capacity | 1024 Wh |
| Net Weight | Approx. 13 kg |
| Dimensions | 448 × 225 × 230 mm (L × B × H) |
| Max. Operating Altitude | 3000 m |
| Output Ports | |
| AC Output [1] (x2) | DYM1000L: 100-120 VAC, 50/60 Hz, 1800 W (nominal), 2200 W (max. continuous output power) DYM1000H: 220-240 VAC, 50/60 Hz, 1800 W (nominal), 2200 W (max. continuous output power) |
| AC Output (bypass mode) | DYM1000L: 100–120 V AC, 12 A, 1440 W DYM1000H: 220–240 V AC, 10 A, 2200 W |
| USB-A Output (x2) | 5 V⎓3 A / 9 V⎓2 A / 12 V⎓2 A Max. output power per port: 24 W |
| USB-C Output (x2) | 5/9/12/15/20 V⎓5 A Max. 140 W per port [2] |
| SDC Output (x2) | SDC [3]: 9-27 V, max. 10 A, max. 240 W SDC Lite: 9-27 V, max. 10 A, max. 240 W |
| Input Ports | |
| AC Input | DYM1000L: 100–120 V AC, 12 A, 1200 W (charging), 1440 W (bypass) DYM1000H: 220-240 V AC, 10 A, 1200 W (charging), 2200 W (bypass) |
| SDC Input (x2) | SDC [3]: 32-58.4 V DC, max. 400 W, max. 8 A SDC Lite: 32-58.4 V DC, max. 400 W, max. 8 A |
| Battery | |
| Cell Chemistry | LFP (Lithium Iron Phosphate) |
| Cycle Life [4] | Maintains over 80% capacity after 3000 cycles |
| Operating Temperature | |
| Temperature for Power Supply | -10 °C to 45 °C |
| Charging Temperature | 0 °C to 45 °C |
| Storage Temperature | -10 °C to 45 °C |
[1] The maximum continuous output power is available when the battery level is higher than 20%. Data for AC output power varies by country and region. If the voltage in Japan is 100 V, the maximum continuous output power for the Japanese version will be 2000 W.
[2] The USB-C port supports a maximum output power of 140 W. The device being charged must support PD 3.1 protocol and use a USB cable that meets EPR specifications.
[3] The SDC port supports a wide range of accessories.
[4] Cycle life is tested under 600W standard charging mode with an output power of 1000 W and at a room temperature of 25 °C (77 °F).
DJI Power 500
| Category | Details |
|---|---|
| General | |
| Model | DYM500L/DYM500H |
| Capacity | 512 Wh |
| Net Weight | Approx. 7.3 kg |
| Dimensions | 305 × 207 × 177 mm (L × B × H) |
| Max. Operating Altitude | 3000 m |
| Output Ports | |
| AC Output [1] (x2) | DYM500L: 100-120 VAC, 50/60 Hz, 800 W (nominal), 1000 W (max. continuous output power) DYM500H: 220-240 VAC, 50/60 Hz, 800 W (nominal), 1000 W (max. continuous output power) |
| AC Output (bypass mode) | DYM500L: 100-120 V AC, max. 1000 W DYM500H: 220-240 V AC, max. 1000 W |
| USB-A Output (x2) | 5 V⎓3 A / 9 V⎓2 A / 12 V⎓2 A Max. output power per port: 24 W |
| USB-C Output (x2) | 5/9/12/15/20 V⎓5 A Max. 100 W per port (requires PD3.0 protocol support) |
| SDC Output | SDC Lite: 9-27 V, max. 240 W |
| Input Ports | |
| AC Input | DYM500L: 100–120 V AC, 540 W (charging), 1000 W (bypass) DYM500H: 220-240 V AC, 540 W (charging), 1000 W (bypass) |
| SDC Input | SDC Lite: 22.4–29.2 V DC, max. 300 W, max. 10 A |
| USB-C Input | 5-20 V DC, max. 100 W (requires PD protocol support) Supports simultaneous charging via two USB-C ports with a maximum power of 200 W. |
| Battery | |
| Cell Chemistry | LFP (Lithium Iron Phosphate) |
| Cycle Life [2] | Maintains over 80% capacity after 3000 cycles |
| Operating Temperature | |
| Temperature for Power Supply | -10 °C to 45 °C |
| Charging Temperature | 0 °C to 45 °C |
| Storage Temperature | -10 °C to 45 °C |
[1] Maximum continuous output power is available when the battery level is higher than 20%.
[2] Cycle life is tested in 270W standard charging mode with an output power of 500 W and at a room temperature of 25 °C (77 °F).
