DJI Power 1000 / Power 500 User Manual

Introduction

The DJI Power 1000 is a portable power station with a capacity of 1024 Wh, weighing approximately 13 kg, and supporting a maximum output power of 2200 W. The DJI Power 500 is a portable power station with a capacity of 512 Wh, weighing approximately 7.3 kg, and supporting a maximum output power of 1000 W.

The power stations offer Fast Recharge and Standard Recharge modes for AC charging. In Fast Recharge mode, the power station can be recharged to 80% in approximately 50 minutes and to 100% in approximately 70 minutes. In Standard Recharge mode, the operating noise is lower, and battery cell life can be extended. Recharging to 100% takes approximately two hours. The power stations feature SDC/SDC Lite ports, allowing them to charge DJI Power intelligent batteries and other devices using various DJI Power accessories, supporting power supply in diverse scenarios.

Note: Charging times are tested at room temperature (25° C / 77° F) in a well-ventilated environment and are for reference only.

Product Profile: DJI Power 1000

The DJI Power 1000 features the following ports and indicators:

Product Profile: DJI Power 500

The DJI Power 500 features the following ports and indicators:

Display Screen

The display screen shows:

System Warnings

ERR: Temperature error. If the temperature is abnormal during Fast Recharge, the temperature error icon will flash slowly. The actual recharge power may be reduced to ensure battery cell life and safety. The icon will become solid if the temperature is too high or too low. Wait for the temperature to return to normal.

OVERLOAD: Overload warning.

For detailed information on warnings and troubleshooting, visit: https://s.dji.com/DJI-Power

Turning On/Off

1. Power On/Off: Press and hold the power button for at least two seconds. The display screen will turn on automatically after powering up.
2. Turn Display Screen On/Off: With the power station on, press the power button once.

Charging External Devices

Output AC

The power station has two AC output ports. Connect external devices to the AC output ports and press the AC output button for AC power supply.

The power station features Automatic AC Shutdown and Auto Shutdown to conserve power. Pressing the AC output button once enables AC output, and the indicator will flash slowly. AC output will automatically turn off if no devices are being charged via the AC output port for half an hour. To enable Continuous AC Output, press and hold the AC output button. The indicator will show a solid light, and the output will not turn off automatically, suitable for devices like refrigerators.

When AC output is deactivated, the power station will automatically shut down if no devices are being charged via the AC output port for one hour.

When recharging with AC input power at different frequencies, the power station will automatically switch to the same frequency as the input power. To manually change the AC output frequency, disconnect the power station from the AC outlet when AC output is enabled, then press and hold the AC output button for 10 seconds.

Note: Internal electronic components have a waterproof coating. A slight odor may be noticeable when high power is used, which will dissipate naturally with daily use.

Output USB

The power station has two USB-A ports and two USB-C ports. Connect external devices to the USB-A or USB-C ports for power supply.

Fast Charging DJI Drone Batteries

The DJI Power 1000 has SDC and SDC Lite ports, while the DJI Power 500 has an SDC Lite port. The power station can quickly charge supported DJI Power intelligent batteries using the SDC fast charging cable (sold separately).

Other SDC Output

The power station can also be used with other SDC cables (sold separately) to charge different devices via the SDC/SDC Lite ports.

Car Charger to SDC Power Cable (12 V): This cable allows the power station to charge devices that use car power, such as car refrigerators. Ensure the external device is within the cable's output specifications (13.6 V, 10 A, 136 W).

XT60 Cable to SDC Power Cable (12 V): This cable provides 12V DC input for devices with an XT60 port. Do not connect directly to lithium batteries with an XT60 port; connect the power station to a balance charger first.

Recharging the Power Station

AC Recharging

The power station offers Fast Recharge and Standard Recharge modes for AC recharging.

Fast Recharge Mode: Offers higher recharge power, reaching 80% in about 50 minutes and 100% in about 70 minutes.

Standard Recharge Mode: Offers lower recharge power and noise, suitable for overnight charging, and can extend battery cell life. Recharging to 100% takes about two hours.

Steps for AC Recharging (using DJI Power 1000 as example):

1. Open the port cover and connect the DJI Power 1000 to an AC outlet using the AC power cable.
2. Toggle the recharge mode switch to set the recharge mode to Fast Recharge (1200W for Power 1000, 540W for Power 500) or Standard Recharge (600W for Power 1000, 270W for Power 500).

Recommendations:

• Disconnect the AC outlet once charging is complete.
• Standard Recharge mode is recommended for longer battery cell life.
• The power station employs a battery cell life protection strategy. After five consecutive Fast Recharge cycles, it will automatically switch to Standard Recharge mode for the sixth recharge to ensure battery maintenance. This maintenance process takes approximately 20 minutes.
• If the temperature is abnormal during Fast Recharge, the temperature error icon will flash slowly. Actual recharge power may be reduced to ensure battery cell life and safety.

Solar Recharging

The power station can be connected to solar panels using the DJI Power Solar Panel Adapter (MPPT) or a Car Charger to SDC Power Cable for solar recharging. Both accessories are sold separately.

Steps for Solar Recharging (using DJI Power 1000 as example):

1. Deploy the solar panel, support it with a stand, and align it towards the sunlight. Adjust the support stand angle. It is recommended that the solar panel surface is perpendicular to the sunlight. Ensure the solar panel is not obstructed.
2. Connect the solar panel using the XT60 cable to the solar panel adapter module to begin recharging.

Important Notes:

• Follow instructions for using solar panels. Do not mix solar panel types, as this can cause damage.
• Up to three solar panels can be connected in parallel to the adapter module for DJI Power 1000 (total of six panels via two adapters). DJI Power 500 can connect one adapter module and up to three solar panels.
• The Car Charger to SDC Power Cable allows connection of one solar panel. The maximum solar panel current must be lower than 10 A, and the output power must be lower than 100 W.
• It is recommended to use DJI-approved Zignes solar panels. If using other panels, ensure they meet the following requirements to prevent damage:
• Open-circuit voltage is lower than 30 V.
• Maximum current of any single solar panel is lower than 10 A.
• If multiple solar panels are used, the total power is lower than 400 W.
• For DJI Power 500, the maximum input power is limited to 300 W when using the SDC Lite port for solar charging.
• Keep the power station away from direct sunlight during recharging. Excessive heat can cause damage.
• Avoid covering solar panel surfaces with leaves or other objects. Partial shading will affect power generation efficiency and may cause overcurrent, damaging components.
• Clean the solar panel surface gently with a soft cloth dampened with clean water.

Car Recharging

The DJI Power Car Outlet to SDC Power Adapter can be used to connect a car power port to the power station's SDC (or SDC Lite) port for recharging.

Important:

• Ensure the car power port input voltage is within 12-30 V and the maximum input current is lower than 8 A. Otherwise, it may cause abnormal performance or damage to the power station.
• Ensure the power adapter is securely connected to the car power port and the car engine is running before recharging.

USB-C Recharging

The DJI Power 500 can be recharged using a USB Power Delivery charger via the USB-C port for a maximum charging power of 100 W. The DJI Power 500 also supports simultaneous power input, allowing two USB-C ports to be used for charging at a maximum power of 200 W.

Uninterruptible Power Supply (UPS)

The power station supports Uninterruptible Power Supply (UPS). Connect the power station to an AC outlet and connect external devices, such as computers, to the power station. Press the AC button once, and a UPS indicator will appear on the display screen. In this mode, the AC output powers the power station and the connected devices. UPS is enabled by default.

If there is a sudden power outage, the power station can automatically switch to battery power supply within 20 ms, ensuring connected devices remain operational.

Warnings:

• The power station only supports basic UPS features and does not support 0ms UPS. Do not connect the power station to devices that require 0ms UPS, such as medical equipment, data servers, or workstations storing critical data, as this may cause device damage or data loss.
• This function may not be available in all regions. Check local laws and regulations for more information.

DJI Power 1000 Connections

1/4" Thread Hole

The DJI Power 1000 features two 1/4" thread holes, allowing users to mount DJI Power Solar Panel Adapters (MPPT). Attach one adapter module according to Diagram A. Align the mounting holes on the bottom of the bracket and attach two adapter modules to the power station according to Diagram B.

Users can also mount devices with 1/4" screws onto the power station.

Protective Storage Bag

The DJI Power 1000 can be used with a protective storage bag. This bag protects the power station from scratches and dust, making it easier to carry. Open the front of the bag to connect external devices to the power station, and the back of the bag is for storing cables and accessories. When using the DJI Power 1000 with the protective storage bag, ensure both sides of the bag are unzipped to prevent the air vents from being blocked, which could cause overheating.

Appendix

Firmware Update

The firmware of the DJI Power 1000 and DJI Power 500 can be updated using DJI Assistant 2 (Power Series). Ensure your computer is connected to the internet before updating the firmware. Follow the instructions below to ensure a successful firmware update:

1. Power off the device. Press and hold the AC button and the power button simultaneously until "LOAD" appears on the display screen.
2. Connect your computer to the designated USB-C port as shown in the diagram.
3. Connect the device to an AC outlet if updating the firmware for DJI Power 1000 with a rated voltage of 100 V or 120 V. Skip this step if updating firmware for other power station models.
4. Launch DJI Assistant 2, select the product, and click the firmware update button on the left.
5. Select the firmware version, read the instructions in DJI Assistant 2 carefully, and click update. The firmware will be downloaded and uploaded to the device automatically.
6. The firmware will update automatically, and the display screen will show the update progress. Wait for the process to complete. The device will restart automatically after the firmware update is finished.

Important:

• DO NOT power off the device or disconnect it from the computer during the firmware update.
• DO NOT disconnect the device from the AC outlet when updating the firmware for DJI Power 1000 with a rated voltage of 100 V or 120 V.
• If the firmware update fails, the display screen will show "UPGD FAIL". Disconnect the device from the computer and the AC outlet, then press and hold the power button for five seconds to power off the device and try again.

Troubleshooting

If any system warnings appear on the display screen, click the link below or scan the QR code for details on warnings and related troubleshooting. If the problem persists, contact DJI Support.

Link: https://s.dji.com/DJI-Power

Maintenance

• If the power station needs to be stored for an extended period, it is recommended to discharge it to 60%. Storing it at a low power level can lead to over-discharge.
• The power station should be stored at a temperature of -10° to 45° C (14° to 113° F), in a cool, dry environment away from direct sunlight. DO NOT place the power station in water or in places prone to leaks.
• DO NOT store the power station for a long time after it has been fully discharged, as the battery may be over-discharged, causing damage to the battery cells.
• Recharge and discharge the power station once every four months to ensure battery performance: discharge the power station to 15%, power it off for more than two hours, and then recharge it to 100% in Standard Recharge mode.
• Clean ports with a clean, dry cloth if significant buildup is present. DO NOT clean the power station with alcohol or other flammable solvents.

Optional Accessories (Sold Separately)

Unless otherwise stated, the accessories are compatible with both DJI Power 1000 and DJI Power 500.

• Solar Panel Zignes
• DJI Power Solar Panel Adapter (MPPT)
• DJI Power Car Outlet to SDC Cable (12V/24V)
• DJI Power SDC Fast Charge Cable to DJI Matrice 30 Series
• DJI Power SDC Fast Charge Cable to DJI Mavic 3 Series
• DJI Power SDC Fast Charge Cable to DJI Air 3 Series
• DJI Power SDC Fast Charge Cable to DJI Inspire 3
• DJI Power SDC to XT60 Cable (12V)
• Car Charger to SDC Power Cable (12 V)

Specifications

DJI Power 1000

DJI Power 500