Parts List
Before assembling the playard, verify you have all the following parts:
- Item 1: Playard (fully assembled)
- Item 1: Mattress
- Item 1: Bassinet
- Item 4: Metal Support Tubes (2 male, 2 female)
- Item 1: Travel / Storage Bag
- Item 1: Diaper Stacker
- Item 1: Mobile Lower Arm
- Item 1: Mobile Arm Holder
- Item 1: Mobile Upper Curved Arm
- Item 1: Mobile Tri-shaped Arm
- Item 3: Toy Animal
Important Instructions
Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.
If you experience any difficulty in using this product, please contact Baby Trend customer service at 1-800-328-7363 between 8:00 A.M. and 4:30 P.M. Pacific Standard Time. Have your model number and manufacturing date available.
Note: Toys and mobile may vary.
Safety Warnings
General Warnings
- WARNING: NEVER LEAVE INFANT IN PRODUCT WITH SIDES DOWN. Infant may roll into space between pad and loose mesh side causing suffocation.
- WARNING: INFANTS CAN SUFFOCATE: In gaps between a mattress too small or too thick and product sides, or on soft bedding. Never add a mattress, pillow, comforter, or padding. Use only the mattress provided by manufacturer. Never use a water mattress.
- WARNING: Failure to follow these warnings and instructions could result in serious injury or death.
- The playard, including side rails, must be fully erected and latches secure before use.
- Strings can cause strangulation! NEVER place items with a string around a child's neck. NEVER suspend strings over playard or attach strings to toys.
- Discontinue use when child can climb out, reaches 35 in. (890 mm), or weighs 30 lbs. (14 kgs), whichever comes first.
- When child can pull to standing, remove bumper pads, large toys, and other objects that could serve as steps for climbing out.
- NEVER place product near a window where cords from blinds or drapes can strangle a child.
- Always provide necessary supervision. NEVER leave child unattended when used for playing.
- To reduce the risk of SIDS, place healthy infants on their back to sleep, unless advised otherwise by a physician.
- Child can become entrapped and die when improvised netting or covers are placed on top of a play yard. Never add such items.
- NEVER use this product if there are loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically. Contact Baby Trend Customer Service for replacement parts. NEVER substitute parts.
- NEVER leave child in product with sides lowered. Ensure sides are raised and locked.
- NEVER use plastic shipping bags or other plastic film as mattress covers not intended for that purpose, as they can cause suffocation.
- This product is not intended for commercial use.
Maintenance and Cleaning
- Use only household mild soap and warm water.
- DO NOT USE BLEACH.
- DO NOT MACHINE WASH.
Assembly Instructions
To Assemble Playard
- Unzip the storage bag and remove the playard frame. Undo the fastening straps and set the mattress aside. Do not push the center down yet.
- Ensure all four (4) top rails are fully erected before lowering the center. Pull up one rail at a time, holding each side of the rail, and pull up sharply. Do not pull from the middle where the center latch release is located. Ensure both tubes latch in place and each rail is rigid. The center must be raised while locking the rails. If one rail locks but the other does not, unlock the rail by squeezing the release in the center and try again.
- Once all four (4) top rails are locked, push down on the center handle. The center mechanism will rotate clockwise 90 degrees and automatically lock. Test each top rail by pushing down slightly to confirm it is rigid and securely in place.
- Place the mattress on the floor of the playard with the padded side facing up.
- Insert the Velcro® straps located on the underside of the mattress through the slots in the floor of each end of the playard. Fasten the hook and loop straps to the underside of the playard floor to prevent the mattress from moving. IMPORTANT: The center handle must remain raised (approx. 45.7 cm or 18 inches) while locking the side rails. If the center is not raised, the rails will not lock. If you experience difficulty, contact Customer Service.
Folding Playard
- Release the Velcro® straps holding the mattress from underneath the playard floor or bassinet and set the mattress aside. Do not unlock top rails yet; the center of the floor must be raised before top rails will unlock. Rotate the center handle counter-clockwise 90 degrees and raise the center as high as the top rails. Gather the legs and wheels together towards the center as close as possible so they nearly touch.
- Locate the rail latch release in the center and bottom side of each rail. Squeeze the lever with two hands until the rail releases the two tubes, then push down. NOTE: If top rails do not release completely, DO NOT FORCE! Lift the center of the floor higher. Both tubes must be released for the top rail to fold.
- Gather the four (4) corners and center them tightly together. Wrap the mattress around the playard frame with the padded side facing inward.
- Secure the hooks and loop straps by feeding them through the loops on the end of the mattress and folding them back onto themselves. Place the folded playard into the carry bag so that the handle comes through the opening between each side of the zipper.
To Assemble Bassinet
ATTENTION: Playard must be fully assembled and securely locked before installing or using the bassinet feature. You will need to remove the mattress from the bottom of the playard to use inside your bassinet.
- Position the bassinet over and down into the fully assembled playard. Secure in place by pushing down firmly on each plastic support clip until all are snapped into place.
- Ensure the tubes are lined up with the holes in the front frame assembly. Insert the assembled mattress support tubes into the loops provided on the bottom of the bassinet.
- Place the mattress into the bassinet with the padded side facing upward.
To Remove Bassinet: Remove mattress from bassinet, remove canopy, unsnap all clips, and lift the bassinet.
Diaper Stacker Assembly
- Connect the diaper stacker to the playard by sliding the two connecting clips over an open portion of the top rail of the playard. NOTE: Diaper stacker can only be installed on open sides of the playard where the connecting clips can easily be attached without interfering with other features.
Mobile Assembly
ATTENTION: A crib mobile is intended for visual stimulation and not to be grasped by the child. If attached to the crib or playpen, remove when baby begins to push up on hands and knees. If designed for wall/ceiling mount, ensure it is out of reach. Always attach all provided fasteners tightly. DO NOT add additional strings/straps. DO NOT attach the mobile with child in playard or bassinet.
- Insert the Mobile Lower Arm into the Mobile Arm Holder until they lock together.
- Insert the Mobile Upper Curved Arm into the Mobile Lower Arm until locked together.
- Snap the Mobile Tri-shaped Arm onto the end of the Upper Curved Arm. Connect each of the three toys to the mobile by threading the string into the slot at the end of each arm.
- Insert the bottom of the Mobile Arm into the frame of the playard.
