UTILITECH Halogen Work Light
Model: MPL1025-C500K9030
Item #: 1107084
Preparation
Estimated Assembly Time: 15 minutes
Tools Required (Not Included): [Tools not specified in document]
Contact Information
For questions, problems, or missing parts, contact:
Phone: 866-994-4148 (8 a.m. - 8 p.m., EST, Monday - Sunday)
Email: ascs@lowes.com
Visit Lowes.com for more information. Search the item number (1107084) and refer to the Guides & Documents tab on the product's page.
Printed in Vietnam
Troubleshooting
| Problem | Possible Cause | Corrective Action |
|---|---|---|
| The work light comes on, but the light is dim. | Improper voltage or power supply. | The work light will only operate on standard household 120 V AC/60 Hz power. Have power supply checked by a qualified electrician. |
Care and Maintenance
Clean the lens, lamp head, and lamp stand regularly with a non-abrasive cleaner. ⚠️ Warning: Always make sure the work light is unplugged and completely cool before attempting to clean it.
Warranty
This fixture is warranted to be free from defects in materials and workmanship for 1 year from the date of original purchase. Call 866-994-4148 to obtain a Return Authorization number and further instructions. The manufacturer will be liable for the replacement of the defective item and will not be liable for any other loss, damage, or injury which is caused by the product.
Safety Information
Please read and understand this entire manual before attempting to assemble, operate, or install the product.
Warnings
- Be sure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
- ⚠️ BE EXTREMELY CAREFUL WHEN USING THIS DEVICE. Improper use of this work light can result in injury or death. Follow all safeguards stated in this manual in addition to normal safety precautions in working with electrical devices. DO NOT attempt to service this device. When using outdoor portable work lights, always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury. Failure to observe the following safety rules may result in FIRE, ELECTRICAL SHOCK, INJURY, or EXPOSURE TO EXCESSIVE ULTRAVIOLET RADIATION.
- Use only 3-wire UL/ETL Listed outdoor extension cords that have 3-prong grounded plugs and grounded receptacles that accept the work light's plug.
- Use only with an 18-gauge (AWG) extension cord of cord type SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A, SJOW, SJOW-A, SJTW-A, or SJTOW, SJTOW-A.
- To avoid electrical shock, DO NOT use near water or in areas where water may accumulate. Keep work light at least 16 ft. (4.87 m) from pools or spas. Keep plugs dry. Use only Ground Fault Circuit Interrupter (GFCI) protected receptacles when using this work light in wet or damp locations. Receptacles are available with built-in GFCI protection and are to be used for this measure of safety.
- Always unplug work light and allow lamp head to cool before replacing bulb.
- The work light lamp heads get HOT very quickly. Only touch the power plug or cushioned handle when turning the lamp head ON or OFF.
- DO NOT touch the glass lens, wire lens guard, or any metal part of the lamp head when the lamp is turned on to avoid burns.
- If exposed skin feels warm while you are in the lighted area, move the work light farther away. DO NOT remain in light if skin feels warm.
- DO NOT look directly at the lighted lamp to avoid eye injuries.
- Always keep the work light away from any flammable surfaces or materials.
- Use only with a 500-watt bulb or lower wattage lamp.
- Never touch the halogen lamp surface with your bare hands. Unplug and allow lamp to completely cool before replacing bulb.
- DO NOT use work light if it has a missing or damaged wire guard, lamp containment barrier, or lens cover.
- Read and follow all safety rules and operating instructions before first use of this product.
Caution
- ⚠️ RISK OF DAMAGING BULB! NEVER TOUCH BULB SURFACE WITH YOUR BARE HANDS! The natural oil from your skin can leave a residue that could cause the bulb to fail prematurely. If you accidentally touch the bulb with your bare hands, wipe the bulb thoroughly with alcohol and soft cloth or tissue before installing. ALWAYS USE A CLEAN CLOTH OR TISSUE WHEN HANDLING THE BULB.
- ⚠️ RISK OF DAMAGE TO WORK LIGHT! The lamp head on this work light is designed to operate safely with a single 500-watt bulb. To avoid damage to the work light, DO NOT USE A BULB OVER 500-watts IN THIS WORK LIGHT.
Installation Overview
The following steps describe the general installation process, referencing the provided diagrams:
- Step 1: Shows the main housing of the work light (labeled Part A).
- Step 2: Illustrates the connection between Part A and Part B.
- Step 3: Depicts Part C being used to secure the assembly of Parts A and B.
- Step 4: Shows Part D being attached to the unit assembled in the previous steps.
- Step 5: Displays a mounting bracket and screws (Hardware AA) for installation.
- Step 6: Illustrates the light head assembly being connected to the stand or bracket.
- Step 7: Shows the fully assembled UTILITECH Halogen Work Light.
Package Contents
- Part A: Work Light Body (x1)
- Part B: Assembly Component (x1)
- Part C: Fastener (x1)
- Part D: Assembly Component (x1)
Hardware Contents
- Hardware AA: Screws (x2)
Access Denied
TRABAJO.La
