IDANÄS Side Table
Assembly Instructions
Important Safety Information
⚠️ WARNING - Delicate table - Do not sit on the product.
⚠️ WARNING – Delicate table - Do not place heavy objects on this product, maximum load 20 kg (44 lb).
Parts List
- Wooden Dowel(104171) - 6x
- Cam Lock(106720) - 4x
- Cam Lock Screw/Pin(119253 / 118137) - 4x
- Connector(10051660 / 10075382) - 4x
- Screw/Bolt(112357 / 10053816) - 4x
- Wooden Dowel(101345) - 12x
- Screw(100211 / 100212) - 4x
- Screw/Bolt(118331) - 8x
- Allen Key/Wrench(100001) - 1x
Assembly Steps
Step 1: Prepare Base Frames
Place the two base frame pieces on a protected surface (e.g., a rug). Attach 4x part 112357/10053816 (screws/bolts) into the pre-drilled holes on the wooden blocks of the base frames.
Visual: Two frame sections laid flat. A close-up shows a screw (112357/10053816) being inserted into a wooden block.
Step 2: Insert Frame Screws
Insert and tighten 8x part 118331 (screws/bolts) into the designated holes on the base frame assembly.
Visual: The base frame sections are now partially assembled. A close-up shows 8 screws (118331) being inserted and tightened.
Step 3: Attach Side Supports
Attach the side support pieces to the frame. Insert 4x part 101345 (wooden dowels) into the blocks, then connect these to the frame. Ensure the connecting plates are oriented correctly, avoiding incorrect connections.
Visual: Side support pieces are being attached. A close-up shows a wooden dowel (101345) being inserted into a block. Another diagram shows correct [✔️] and incorrect [❌] orientations of connecting plates.
Step 4: Attach Vertical Posts
Attach the vertical frame posts. Insert 2x cam locks (106720) into the designated holes and tighten them with 2x cam lock screws (119253/118137).
Visual: Two vertical posts are being inserted into the frame. Close-ups show the insertion of cam locks (106720) and cam lock screws (119253/118137), and the tightening action.
Step 5: Attach Remaining Side Supports
With the frame upside down, attach the remaining side support pieces. Insert 4x part 101345 (wooden dowels) into the blocks.
Visual: The frame is shown upside down. A close-up illustrates inserting wooden dowels (101345) into blocks.
Step 6: Attach Remaining Vertical Posts
Attach the remaining vertical frame posts. Insert 2x cam locks (106720) and tighten them with 2x cam lock screws (119253/118137).
Visual: The frame is upside down. Close-ups show the insertion and tightening of cam locks (106720) and cam lock screws (119253/118137).
Step 7: Insert Shelf Supports
With the frame upright, insert 4x part 118331 (screws/bolts) into the designated holes on the frame.
Visual: The frame is upright. A close-up shows 4 screws/bolts (118331) being inserted.
Step 8: Secure Shelf Supports
Attach the shelf supports. Insert 2x cam locks (119253/118137) and tighten them. Then, insert 2x cam locks (106720) and tighten them.
Visual: Close-ups show the process of inserting and tightening cam locks (119253/118137) and then cam locks (106720).
Step 9: Attach Top Frame
Attach the top frame. Insert 6x part 104171 (wooden dowels) and secure with cam locks. Ensure correct connection [✔️], avoid incorrect connection [❌].
Visual: The frame is upright. A close-up shows dowels (104171) being inserted and cam locks being used. An incorrect connection is marked with a cross.
Step 10: Insert Shelves
Carefully place the shelves into the assembled frame.
Visual: Shelves are shown being lowered into the frame structure.
Step 11: Secure Shelves
Secure the shelves using 4x part 10051660/10075382 (connectors).
Visual: A close-up shows connectors (10051660/10075382) being attached to secure the shelves.
Step 12: Secure Shelves
Secure the shelves using another 4x part 10051660/10075382 (connectors).
Visual: A close-up shows connectors (10051660/10075382) being attached to secure the shelves.
Step 13: Attach Top Frame Elements
Attach additional elements to the top frame. Insert 4x part 101345 (wooden dowels).
Visual: The frame is upright. A close-up shows 4 wooden dowels (101345) being inserted into the top frame.
Step 14: Place Tabletop
Carefully place the tabletop onto the assembled frame, aligning it with the dowels and frame structure.
Visual: The tabletop is shown being lowered onto the completed frame.
Step 15: Secure Tabletop
Secure the tabletop. Use the Allen key (100001) to tighten 4x screws (100211/100212) through the frame into the tabletop.
Visual: A close-up shows the Allen key (100001) being used to tighten screws (100211/100212) from underneath the frame into the tabletop.
