Instruction Manual

Introduction

1.1 SEE378

The SEE378 Anti-Vandal Dome camera features a tough metal exterior, making it suitable for both outdoor and indoor use. This 4K model, also known as 8MP, delivers stunning Ultra-HD quality, capturing fine details. It is designed for high-end installations and is compatible with 4K DVRs, such as the Zip Xtreme. Its 4K resolution and true day-night filter make it an excellent choice for professional installers.

Tools & Handy Extras

• Screwdriver
• Drill
• 12V DC PSU
• Drill bits
• BNC Crimp Tool & BNCs
• RG59 Coax Cable
• Digital Multi-Meter
• LCD400K - CCTV Test monitor

Connections & Dipswitches

The camera requires a 2.1mm DC socket for power, using a regulated 12V DC power supply rated above the camera's current draw. The camera is polarity sensitive, so connections must be made correctly.

A standard BNC connector provides the 4-in-1 video output, which can be switched to AHD, CVI, or CVBS formats as needed.

Dipswitch 4-In-1 Technology

The camera supports selectable HD-TVI, HD-CVI, AHD, and CVBS (Analogue) outputs. By default, the camera is set to HD-TVI. The output format can be changed using the dip switches located on the camera's fly-lead. Note that the "Output Mode" setting in the DVR's menu does not override the dip switch configuration.

Dip switch configuration:

[ON] [OFF] [ON] [OFF] [ON] [OFF] [ON] [OFF]
1 2 1 2 1 2 1 2
TVI AHD CVBS CVI

Mounting

5.1 Anti-Vandal Dome

Step 1: Loosen the three Torx screws in the upper housing and lift off the housing (Torx key is supplied).

Step 2: Screw through the camera's base and into the mounting surface using the provided screws and wall plugs.

Step 3: Once the camera is positioned, replace the upper housing and fasten the three Torx screws.

A template is included in the box for marking the hole positions for the fixing screws.

Motorised Lens

To access the Motorised Lens features via coaxitron:

1. Click on the image in Live view.
2. Click on the PTZ button at the bottom of the screen.
3. Use the Zoom + and - buttons to zoom in and out. The camera will automatically focus when the Zoom +/- button is released.

Control interface:

[UTC] [PTZ] [PRESET]
⬆️ ➡️ ⬆️
⬅️ [Center] ➡️
⬇️ ⬇️ ⬇️
SPEED: [----- Slider -----] 20
Step: [ 5 ]
ZOOM: [ - ] [ + ]
FOCUS: [ - ] [ + ]
IRIS: [ - ] [ + ]

OSD Menu

Access to the camera's menu is via Coaxitron. For ZIP DVRs, ZIP Coaxitron is the default setting.

To access the Cameras Menu via coaxitron:

1. Click on the image in Live view.
2. Click on the PTZ button at the bottom of the screen.
3. Click on the IRIS + / centre button to display the menu.

Use the directional arrows to navigate up and down through the menu. Use the directional arrows left and right to change the selected option. Use IRIS + to select and enter a menu option.

7.1 8MP OSD Menu Motorised

OSD Menu Settings (Continued)

OSD Menu Settings (Continued)

7.2 Key Menu Settings

Exposure Mode: AUTO / GLOBE / GLOBAL sets the required shutter speed for the current light level. The shutter speed automatically adjusts to keep the digital sensor exposed to light. The FLK option sets the shutter speed to stop synchronization with lighting, minimizing pulsing effects.

White Balance: Adjusts color settings to make objects appear natural. ATW / PRO (Automatic tracking white balance) continuously tracks and adjusts white balance, suitable for cameras with changing image content and lighting.

Day & Night: The camera can be set to color or B&W mode, or switch automatically. 'External' is the default, where the switch is controlled by an external trigger, such as a light-dependent resistor.

DNR (Noise Reduction): This process removes noise from the video signal using a digital filter. 2D noise reduction targets foreground noise, while 3D noise reduction addresses noise in both the foreground and background.

D-WDR: Digitally adjusts exposure in different frame areas to maintain optimum levels in both dark and bright regions. Note: Some models may not feature D-WDR.

Reset: Restores the camera to factory default settings. This is useful for troubleshooting when issues arise, ensuring all settings are reset.

Troubleshooting

8.1 Camera Rebooting / Turning Off

1. Check the camera's voltage under load using a digital multi-meter. If below 10.8V, move the power supply closer to the camera.
2. For 12V DC cameras, use only a regulated power supply rated above the current consumption to ensure consistent supply.
3. Use thicker gauge copper cabling to reduce voltage drop. Thicker cable lowers resistance between the camera and power supply, thus reducing voltage drop along the cable.

8.2 Poor Quality Images

1. Check the video format supported by the DVR (digital video recorder) and set the camera to the relevant format (refer to 4-In-1 Technology).
2. If set to CVBS, this is a low-quality output for legacy systems. For 2 MegaPixel DVRs or above, use a different format like HD-TVI.
3. Reset the camera menu via Zip Coaxitron (refer to OSD Menu, page 5).
4. Verify that the DVR supports the camera's resolution.

8.3 Image is Black & White

1. Check the video format supported by your DVR and set the camera to the relevant format (refer to 4-In-1 Technology).
2. Reset the camera menu via Zip Coaxitron (refer to OSD Menu, page 5).
3. Verify that the DVR supports the camera's resolution.

8.4 NCD / No Image Displayed on Recorder

1. Check the camera's voltage under load using a digital multi-meter. If below 10.8V, move the power supply closer to the camera.
2. For 12V DC cameras, use only a regulated power supply rated above the current consumption to ensure consistent supply.
3. Use thicker gauge copper cabling to reduce voltage drop. Thicker cable lowers resistance between the camera and power supply, thus reducing voltage drop along the cable.
4. Ensure the BNC-BNC lead connected between the camera and DVR has no shorts between ground and the center core (positive), or open circuits along the center core or ground.

General Maintenance

Routinely clean the camera to prevent dust buildup, which can affect performance. A damp, non-abrasive microfibre cloth is recommended.

Regularly check power and data connections for water ingress and corrosion.

Ensure cameras are firmly attached to the wall or mounting bracket.

Check playback on the recorder to confirm the camera is recording and triggering correctly.

Specification

10.1 SEE378

Conditions

11.1 General Company Disclaimer

All specifications are approximate. System Q Ltd reserves the right to change product specifications or features without notice. While every effort is made to ensure these instructions are complete and accurate, System Q Ltd cannot be held responsible for any losses arising from errors or omissions in these instructions, or from the performance or non-performance of the equipment referenced.

11.2 WEEE Declaration

This symbol on the products and/or accompanying documents signifies that used electronic equipment must not be mixed with general household waste. For treatment, recovery, and recycling, please return this unit to your trade supplier or a locally designated WEE/CG0783SS collection point as defined by your local council.

11.3 Copyright

© Copyright 2022. Zip is a registered trademark of System Q Ltd, Chesterfield, Derbyshire. S40 2WB.