Gira System 106 Camera Module 5561 000

Front View

1. Glass front panel

2. Camera lens opening

Rear View

1. Rotary latch (4 pcs.)

2. Rotary switch: selection of image area (0-9)

3. Socket (2 pcs.): system cable

4. Socket: video cable

5. Fastening for glass front panel (4 pcs.)

General Safety Information

Important: Connection and installation work on electrical equipment should only be performed by a qualified electrician!

This manual is an integral part of the product and must remain with the end customer.

Required Accessories

• System 106 video door station module (art. no. 5563..) with call button module (art. no. 555...) or door station module (art. no. 5565 9..).
• Video door station power supply (art. no. 1288 00).
• Gira video indoor station (e.g., Gira surface-mounted video indoor station Plus).
• Gira System 106 surface-mounted housing, 1-5-gang (art. no. 5501..., 5502..., 5503..., 5504..., 5505...).

Accessories

• Power supply for the door station system, 24 V DC, 300 mA (art. no. 1296 00).

Principle of Operation

The camera module complements the Gira System 106 door station system by adding the "Video" function.

Scope of Delivery

• 1 System 106 camera module
• 1 instruction manual
• 1 short video cable
• 1 long video cable

Check the contents of the packaging for completeness and integrity. For claims, refer to the "Warranty" section.

Equipment Description

Camera Heating System

The camera is equipped with two internal heaters. The second heater is required in case the weather changes abruptly due to local conditions and the front glass fogs up. The use of the second heater requires an additional power supply (ZV). The first heater automatically switches on at temperatures below 6 °C and switches off again at temperatures above +12 °C.

Night Mode

Automatic switch to night mode: During an active conversation, the camera automatically switches to night mode when the brightness level is below 1 lux. Night mode = black and white image and active High Light Compensation (HLC) function. Infrared illumination is active only if this function has been pre-configured on the indoor station.

Noise Reduction Mode (NR)

The NR mode eliminates image interference from the camera in twilight conditions.

Infrared Illumination

IR illumination allows for glare-free images of the field of view in night mode. When using ZV, the range of the IR illumination increases by 3 m.

High Light Compensation (HLC) Function

The HLC function is used to invert bright areas in night mode. Very bright areas are inverted into black (e.g., light from car headlights).

Wide Dynamic Range (WD) Function

The WD function automatically adjusts the brightness of the camera image so that all areas are clearly visible. This ensures that people in dark areas of the camera image become visible.

Mounting the Module

Refer to the installation instructions for the Gira System 106 surface-mounted housing (1-5-gang) for the following installation steps:

• Secure the module onto the functional support.
• Connect the connecting cable.
• Install the terminating resistors.

Terminating Resistor

Starting with the 2-gang surface-mounted housing, two terminating resistors are always included. The terminating resistors are always connected to the first and last modules on the system cable (see the instruction manual supplied with the 1-5-gang surface-mounted housing).

Connecting the Video Cable

Insert the video cable into the camera module socket and into the socket of the video door station module or door station module.

Commissioning the Camera Module

When assigning the call button (see the instruction manual for the door station module or call button module), the camera module registration is performed automatically. All components (System 106 modules, indoor stations, power supplies, etc.) must be installed beforehand for successful commissioning.

Module Configuration

Image Area Adjustment

Using the rotary switch on the back, specific areas (highlighted in white) of the full image (shaded gray) can be magnified. The visible field of view corresponds to the image transmitted to the indoor station, not the position of the camera lens. Position "0" = delivery state.

Mounting Location Selection

When selecting the mounting location, consider the following:

• Backlight: Do not install the camera lens facing bright backlight, e.g., streetlights or garden lighting; do not expose the camera lens to direct sunlight.
• Background: Do not install the camera facing a background that is too bright or has sharp contrasts.
• Lighting: If additional lighting is used in the entrance area, the light from it should not fall directly onto the camera lens (see "Backlight" point).
• Installation height: 1.50 m (recommendation).
• Field of view: 100°.

Technical Specifications

Power Supply: From the system (flat cable, 10-pin); 2 cameras - from the video door station power supply.

Power Consumption:

• Standby (T > 6 °C): 80 mW
• Standby (T < 6 °C): 1.2 W (heating 1 on)
• Active Camera: 2.7 W
• Connections: 2 system cables (flat cables, 10-pin), 1 video cable (analog)

Camera Sensor:

• Type: CMOS 1/3 inch
• Resolution: 2 MP
• Visible Field of View: 100°
• Displayed Field of View (on screen): 105° (rotary switch in position 9), 85° in standard 4:3 format
• Color System: PAL
• Video Resolution (analog CVBS): 50 Hz/625 lines
• Light Sensitivity (in black and white mode): 0.1 lux
• Electronic Shutter Time: up to 1/60,000 s

Installation Height: Recommended 1.50 m

Ambient Temperature: -25 to +70 °C

Degree of Protection: IP54

Dimensions (W x H): 106.5 x 106.5 mm

Adjustment via Other Door Station System Devices

The following settings are made directly on the indoor stations:

• Brightness, contrast, color, and activation time, IR illumination.

Further information can be found in the instruction manual supplied with the respective indoor station.

Replacing the Glass Front Panel

In case of damage to the glass front panel, please contact the dealer from whom the product was purchased (specialist retailer / installation company / electrical wholesaler). The Gira service center will send the device to the dealer for replacement. After replacement, the damaged device will be returned to the Gira service center.

Warranty

Warranty is provided within the legal provisions for specialized trade. Please hand over or send the defective devices postage-paid with a description of the defect to the respective dealer (specialized trade organization / electrical installation company / electrical wholesale company). They will forward the devices to the Gira Service Center.

Gira

Gira Giersiepen GmbH & Co. KG

Electrical installation products

P.O. Box 1220

42461 Radevormwald

Tel. +49 2195 602 - 0

Fax +49 2195 602 191

info@gira.de

www.gira.de/com/ru