GIRA System 106 Voice Module
Model: 5563 9..
General Safety Instructions
⚠️ Installation and electrical work must be performed by qualified electricians.
ℹ️ This manual is part of the product and remains with the end customer.
Required Accessories
- System 106 Call Button Module (Art. No. 555...)
- Audio Control Unit (Art. No. 1287 00)
- System 106 1- to 4-gang Call Button Module (Art. No. 5531 9.., 5532 9.., 5533 9.., 5534 9..)
- 1- to 5-gang flush-mounted housing for System 106 (Art. No. 550x...) or 1- to 5-gang flush-mounted cover for System 106 (Art. No. 551x..., resp. 552x...)
- GIRA Home Station (e.g., surface-mounted home station)
Accessories
- System 106 1- to 4-gang button module (for extensions beyond 4-gang button modules).
- Power supply for input communication DC 24 V 300 mA (Art. No. 1296 00) for auxiliary power (ZV).
Function Description
The Voice Module is the central module of the GIRA System 106 input communication system. It serves the communication function and supplies power to all modules connected to it. It also switches the backlighting of connected call button modules on or off depending on ambient brightness.
Scope of Delivery
- 1 x System 106 Voice Module
- 1 x User Manual
Check package contents for completeness and integrity. For warranty claims, see "Warranty" section.
Module Views
Front View
1: Opening for microphone and speaker ?/?
2: Status LED ?
Rear View
1: Rotary closure (4x) ⚙️
2: Port: Video ?
3: Port (2x): System cable ?
4: Mounting (4x): Front part of the module
5: Terminal block: Power (BUS) ? and auxiliary power (ZV) ⚡
Module Installation
Refer to the installation manual for the 1- to 5-gang flush-mounted housing for System 106 for the following steps:
- Secure the module to the functional bracket.
- Connect the connecting cable.
- Install termination resistors.
Termination Resistor
Two termination resistors are always included with the 2-gang flush-mounted housing. Termination resistors are always connected to the first and last module on the system cable.
Terminal Block Mounting Position
Observe the correct mounting position (rotated) of the terminal block (see installation manual for 1- to 5-gang flush-mounted housing).
No Bridging between BUS and ZV
No bridges must be placed between BUS and ZV on the module. The module automatically recognizes if auxiliary power (ZV) is connected.
Module Commissioning
The Voice Module can only be commissioned in conjunction with a call button module via the control unit (see installation and operation manual for the control unit). All other devices (System 106 modules, home stations, control unit, etc.) must be pre-installed for successful commissioning.
Module Configuration
Volume Control
Volume control is performed on the call button module (see user manual for call button module).
Activating/Deactivating Audible Signal for Call Buttons
Activating or deactivating the audible signal for call buttons occurs on the call button module (see user manual for call button module). In the activated programming mode, all confirmation tones are also emitted.
Status LED
| LED Status | Meaning |
|---|---|
| Orange blinking ? | Programming mode is active. |
| Continuous red ? | Failure of auxiliary power (ZV), short circuit, or undervoltage of the system bus, or ZV voltage > 30 V. |
| Short green blink ? | Confirmation of button press. |
Replacing the Front Panel
- Open the housing and remove the functional bracket.
- Release the voice module and remove it from the functional bracket.
- Loosen the mounting screws ? and remove the front panel with the seal.
- Insert the new seal into the module housing.
- Press the module housing with the pre-assembled seal against the front panel.
- Screw in the 4 screws with a tightening torque of 0.75 Nm. Observe the sequence 1–4 when screwing, see illustration.
Technical Data
| Power Supply | Control unit or auxiliary power (ZV) (DC 24 V 300 mA) |
| Voice Connection Power Consumption | Approx. 1.0 W |
| Standby Mode | 200 mW |
| Connections | 1 x 2-wire bus ? 1 x ZV ⚡ 2 x system ? 1 x video ? |
| Ambient Temperature | -25 °C to +70 °C |
| Degree of Protection | IP54 |
| Dimensions (W x H) | 106.5 x 106.5 mm |
Warranty
Warranty is handled according to legal provisions through the specialist dealer. Please return or send defective devices to your responsible dealer (specialist dealer/installation company/electrical specialist dealer) without postage costs, along with a description of the fault. The dealer will forward the devices to the Gira Service Center.
