GIRA System 106 Voice Module
Article No. 5563 9..
General Safety Warnings
Electrical devices may only be connected and installed by qualified electricians!
These instructions are an integral part of the product and must remain with the end customer.
Required Accessories
- System 106 Keypad Call Module (Art. No. 555 ...)
- Audio Control Unit (Art. No. 1287 00)
- System 106 Keypad Call Module 1- to 4-gang (Art. No. 5531 9.., 5532 9.., 5533 9.., 5534 9..)
- 1- to 5-gang System 106 surface-mounted housing (Cat. No. 550x ...) or 1- to 5-gang System 106 flush-mounted housing (Cat. No. 551x ... or 552x ...)
- GIRA Interior Unit (e.g., surface-mounted interior units)
Accessories
- System 106 Keypad Module 1- to 4-gang (for expansion from 4-gang keypad modules onwards)
- Power Supply for Door Communication DC 24 V 300 mA (Art. No. 1296 00) for additional power supply (ZV)
Description of Operation
The voice module is the central module of the communication system for connection with the GIRA System 106 door station. The module provides voice communication and electrical power for all modules connected to the voice module. Additionally, the voice module switches the backlight of connected keypad call modules on or off depending on ambient light levels.
Delivery Scope
- 1 x System 106 Voice Module
- 1 x User Manual
Check that the package contents are complete and undamaged. For complaints, refer to the 'Warranty' section.
Device Description
Front View
- 1: Opening for microphone and speaker
- 2: Status LED indicator
Rear View
- 1: Rotary latch (4x)
- 2: Connector for video signal
- 3: Two connectors for system cable
- 4: Fastening points (4x) for the module faceplate
- 5: Terminal block for power supply (BUS) and additional power supply (ZV)
Module Installation
The following work steps can be found in the installation instructions for the 1- to 5-gang System 106 surface-mounted housing:
- Lock the module onto the function carrier.
- Connect the connecting cable.
- Insert terminating resistors.
Terminating Resistor
From 2-gang housings onwards, two terminating resistors are always included. Terminating resistors must always be inserted on the first and last module on the system cable.
Terminal Block Installation Position
Pay attention to the correct installation position (orientation) of the terminal block (see installation instructions for the 1- to 5-gang System 106 housing).
Prohibition of Bridging between BUS and Additional Power Supply (ZV)
Bridging contacts between the BUS and the additional power supply (ZV) is not permitted on the module. The module automatically detects whether an additional power supply (ZV) is connected.
Module Startup
The voice module can only be started in conjunction with a keypad call module via the control unit (see installation and operating instructions for the control unit). For successful startup, all other system devices (System 106 modules, interior units, control unit, etc.) must be installed first.
Module Configuration
Volume Control
Volume control is performed on the keypad call module (see operating instructions for the keypad call module).
Activating or Deactivating Key Press Tone Confirmation
The audible confirmation tone for key presses can be activated or deactivated on the keypad call module (see operating instructions for the keypad call module). In active programming mode, all confirmation tones remain active.
Status LED
| LED | Meaning |
|---|---|
| Flashing orange | Programming mode is active |
| Solid red | Failure of additional power supply ZV, short circuit, or system bus undervoltage, or additional power supply ZV voltage > 30 V |
| Short flashing green | Key press confirmation |
Module Faceplate Replacement
- Open the housing and remove the function carrier.
- Release the voice module and remove it from the function carrier.
- Loosen the fastening screws and remove the module faceplate with the seal.
Diagram showing components for faceplate replacement:
- 1: Module faceplate
- 2: Seals
- 3: System 106 Voice Module
- 4: Fastening screws (4x)
The diagram also indicates the tightening sequence for screws (1-4).
- Insert a new seal into the module housing.
- Press the module housing with the pre-installed seal against the module faceplate.
- Tighten the 4 screws with a torque of 0.75 Nm. Observe the tightening sequence, 1-4, as shown in the figure.
Technical Data
| Power Supply: | Via control unit or via additional power supply ZV (DC 24 V 300 mA) |
| Consumption during established voice connection: | Approx. 1.0 W |
| Standby mode: | 200 mW |
| Connections: | 1 x 2-wire line, 1 x ZV, 2 x system, 1 x video |
| Ambient Temperature: | -25 °C to +70 °C |
| Protection rating: | IP54 |
| Dimensions (W x H): | 106.5 x 106.5 mm |
Warranty
Warranty is provided in accordance with statutory regulations through the technical goods trade. Hand over or send defective devices postage-paid with an attached error description to our authorized dealer (technical goods store/installation company/electrical goods store). They will forward the devices to the GIRA Service Center.
Manufacturer
GIRA Giersiepen GmbH & Co KG
Electrical Installation Systems
P.O. Box 1220
42461 Radevormwald
Tel. +49 2195 602 - 0
Fax +49 2195 602 - 191
info@gira.de
www.gira.de
