Gira System 106 Voice Module

General Safety Notes

✔️ The connection and installation of electrical devices must only be carried out by electricians!

This manual is part of this product and must remain with the end customer.

Required Accessories

• System 106 Door-line buttons module (art. no. 555...).
• Audio control unit (art. no. 1287 00).
• System 106 Door-line buttons module 1-4 (art. no. 5531 9.., 5532 9.., 5533 9.., 5534 9..).
• System 106 surface-mounting box for 1 to 5 elements (art. no. 550x ...) or System 106 flush-mounting box for 1 to 5 elements (art. no. 551x ... or 552x ...).
• Gira indoor station (e.g., surface-mounting indoor station).

Accessories

• System 106 Door-line buttons module 1 to 4 (for expansion from a 4-button module).
• Power supply for intercom DC 24 V 300 mA (art. no. 129600) for additional power supply (AA).

Functional Description

The voice module is the central module of the Gira System 106 intercom system. The module serves both for voice function and for supplying power to all modules connected to the voice module. Furthermore, the voice module switches the backlighting of connected door-line button modules on or off depending on the ambient brightness.

Scope of Delivery

• 1 x System 106 Voice Module
• 1 x User Manual

Check the contents of the package for completeness. In case of complaint, see the "Warranty".

Device Description

Front View

1 Microphone and loudspeaker opening: This is where the microphone and loudspeaker are located.

2 Status LED: Indicates the operating status of the module.

Rear View

1 Rotary lock (4x): Used for securing the module.

2 Video port: For video signal connection.

3 System cable port (2x): Connects to the system bus.

4 Module front fastening (4x): Secures the module front.

5 Plug-in terminal: Power supply (BUS) and additional power supply (AA): For connecting power sources.

Module Mounting

The following work steps can be found in the mounting instructions for the System 106 surface-mounting box for 1 to 5 elements:

• Locking the module onto the functional element.
• Connecting the cable.
• Connecting termination resistors.

Termination Resistor

With surface-mounting boxes for 2 elements or more, two termination resistors are always supplied. The termination resistors are always connected to the first and last module in the system cable.

Plug-in Terminal Position

Ensure that the plug-in terminal is correctly oriented (see the user instructions for the System 106 surface-mounting box for 1 to 5 elements).

No BUS and AA Jumper

No jumpers should be placed between the BUS and the AA on the module. The module automatically detects if an additional power supply (AA) is connected.

Module Commissioning

The voice module can only be commissioned in combination with a door-line button module via the control unit (see the user and mounting instructions for the control unit). For successful commissioning, all other devices (System 106 modules, indoor stations, control unit, etc.) must be installed first.

Module Configuration

Volume Adjustment

Volume adjustment takes place on the door-line button module (see the user manual for the door-line button module).

Activating or Deactivating Acoustic Call Acknowledgment

Activating or deactivating the acoustic call acknowledgment takes place on the door-line button module (see the user manual for the door-line button module). In programming mode, all confirmation tones will be emitted.

Status LED

Changing the Module Front

1. Open the housing and remove the functional elements.
2. Unlock the voice module and separate it from the functional element.
3. Loosen the fastening screws and remove the module front, including the seal.

Parts:

• 1 Module front
• 2 Seals
• 3 System 106 Voice Module
• 4 Fastening screws (4x)

4. Place a new seal in the module housing.
5. Press the module housing with the pre-mounted seal against the module front.
6. Tighten the 4 screws with a torque of 0.75 Nm. When tightening, follow the sequence 1-4 shown in the figure.

Technical Data

Warranty

The warranty is offered within the framework of legal provisions through specialized trade. Return or send defective devices postage-paid, with a description of the problem, to your relevant dealer (specialized shop, installation company, electrical retailer). They will arrange for the devices to be sent to the Gira Service Center.

Gira

Gira
Giersiepen GmbH & Co. KG
Electrical installation systems
P.O. Box 1220
42461 Radevormwald
Tel. +49 2195 602 - 0
Fax +49 2195 602 - 191
info@gira.de
www.gira.de