Gira System 106 Voice Module - User Manual
Device Description
Front View
1. Microphone and loudspeaker opening
2. Status LED
Rear View
1. Rotary lock (4x)
2. Video Port
3. System cable port (2x)
4. Module fastening (4x)
5. Plug-in terminal: System cable power supply (BUS) and additional power supply (ZV)
General Safety Notes
The connection and installation of electrical devices must only be carried out by electricians!
This manual is part of the product and must remain with the end customer.
Required Accessories
- System 106 Keypad Module (Art. No. 555...).
- Audio control unit (Art. No. 1287 00).
- System 106 Keypad Module 1-4 (Art. No. 5531 9.., 5532 9.., 5533 9.., 5534 9..).
- Gira indoor intercom.
- Surface-mounting box for 1 to 5 System 106 elements (Art. No. 5501..., 5502..., 5503..., 5504..., 5505...).
Accessories
- System 106 Keypad Module 1 to 4 (for expansion from a 4-gang keypad module).
- Power supply for intercom DC 24 V 300 mA (Art. No. 1296 00) for additional power supply (ZV).
Functional Description
The Voice Module is the central module of the Gira System 106 intercom system. The module serves both for voice function and for powering all modules connected to the Voice Module. Furthermore, the Voice Module switches the backlighting of connected Keypad Modules on or off depending on the ambient brightness.
Scope of delivery:
- 1 x System 106 Voice Module
- 1 x User manual
Check the contents of the package for completeness. In case of a claim, refer to the "Warranty".
Module Installation
The following work steps can be found in the installation instructions for the surface-mounting box for 1 to 5 System 106 elements:
- Locking the module onto the functional element.
- Connecting the cable.
- Connecting terminating resistors.
Terminating Resistors
With surface-mounting boxes from 2 elements, two terminating resistors are always supplied. The terminating resistors are always connected to the first and last module in the system cable.
Plug-in Terminal Position
Pay attention to the correct (offset) mounting position of the plug-in terminal.
Module Configuration
Volume Control
Volume control is set on the Keypad Module (see user manual for the Keypad Module).
Activating or Deactivating Acoustic Confirmation of Key Press
Activation or deactivation of the acoustic confirmation of key press is set on the Keypad Module (see user manual for the Keypad Module). In the activated programming mode, all confirmation tones will be emitted.
Status LED
| LED | Meaning |
| Flashes orange | Programming mode active |
| Lights permanently red | Power supply failure, short circuit, or low system bus voltage or additional supply voltage > 30 V |
| Flashes briefly green | Confirmation of key press activation |
Changing the Module Front
- Open the housing and remove the functional elements.
- Unlock the Voice Module and separate it from the functional element.
- Loosen the fastening screws and remove the module front including seals.
- Place the new module front with the new seals and reassemble in reverse order.
Technical Data
| Power supply: | via control unit or via additional power supply (DC 24 V 300 mA) |
| Power consumption during conversation: | approx. 1.0 W |
| Standby operation: | 200 mW |
| Connections: | 2-wire bus, 2 x additional power supplies, 2 x System, 1 x Video |
| Ambient temperature: | -25 °C to +70 °C |
| Protection type: | IP54 |
| Dimensions (W x H): | 106.5 x 106.5 mm |
Warranty
The warranty is provided within the scope of legal regulations through specialized trade. Deliver or send defective devices postage-paid, with a description of the problem, to your relevant dealer (specialized establishment, installation company, electrical establishment). They will arrange for the devices to be sent to the Gira Service Center.
Gira
Gira
Giersiepen GmbH & Co. KG
Electrical installation systems
P.O. Box 1220
42461 Radevormwald
Tel. +49 2195 602 - 0
Fax +49 2195 602 - 191
info@gira.de
www.gira.de
