Baby Trend SS88 Sit N' Stand Snap Gear Double Stroller

Safety Warnings

⚠️ WARNING: Please follow all of these instructions to ensure the safety of your child. Keep these instructions for future reference.

⚠️ WARNING: Failure to follow these instructions could result in serious injury or death. Avoid serious injury from falling or sliding out, always use the safety harness and ensure that the children are properly positioned according to these instructions.

⚠️ WARNING: Never leave children unattended.

⚠️ WARNING: Care must be taken when folding and unfolding the stroller to prevent finger entrapment.

• ONLY approved Snap Tech™ products can be used on the frame.
• Purses, shopping bags, parcels, diaper bags, or accessory items may change the balance of the stroller and cause a hazardous, unstable condition.
• The maximum weight that can be carried in the storage basket is 5 lbs (2.26 kg). Excessive weight may cause a hazardous unstable condition.
• Be certain the stroller is completely opened and locked in place before allowing a child near the stroller.
• The maximum weight for the Toddler seats is 40 lbs (18.14 kg) each. The maximum weight for the platform/jumpseat is 50 lbs (22.67 kg).
• The Joy Ride Platform / jump seat is designed for a child who is at least 2 1/2 years old and not over 40 inches (101.6 cm) tall. Children totaling more than 90 pounds (40.82 kg) will cause excessive wear and stress on the stroller and may cause a hazardous unstable condition.
• NEVER use the stroller on stairways or escalators.
• NEVER allow your stroller to be used as a toy.
• To clean, use only mild household soap or detergent and warm water on a sponge or clean cloth.
• Check your stroller regularly for loose screws, worn parts, torn material, or stitching. Replace or repair parts as needed.
• Discontinue use of stroller if it malfunctions or becomes damaged. Please contact customer service for repair or replacement parts.

Parts List

Check that you have all the parts for this model before assembling the stroller.

• Stroller: The main stroller frame and chassis.
• Seats (2): Two stroller seats.
• Front Wheels: Two front wheels.
• Rear Wheels: Two rear wheels.
• Removable Joy Ride Platform: A detachable platform for an older child.
• Canopies (2): Two protective canopies for the seats.
• Bumper Bars (2): Two front bumper bars.

Assembly Instructions

IMPORTANT! To ensure safe operation of your stroller, please follow these instructions carefully. Keep these instructions for future reference.

IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts, or sharp edges. NEVER use if any parts are missing or broken.

IMPORTANT! Adult assembly is required.

Remove stroller from box. The front and rear wheels MUST be installed prior to use.

Front Wheels

To attach the front wheels:

1. Unlock the release lever (refer to diagram showing lever). Unfold the stroller frame by pulling upward on the stroller handle until the frame locks into place (refer to diagram showing frame locking).
2. Lean the stroller backwards and push each front wheel assembly into the front wheel housing until they lock into place (refer to diagram showing wheel insertion). NOTE: Pull on the wheel assembly to ensure that it is securely attached to the stroller.

Rear Wheels

1. Press the rear wheel posts into the rear frame hub until it clicks into place (refer to diagram showing rear wheel insertion). NOTE: Pull on the rear wheels to ensure that they are securely attached to the stroller.

Bumper Bar

⚠️ WARNING: Do not use the bumper bar to carry the seat with a child inside. The bumper bar is not a carrying handle.

1. Attach the bumper bar by lining up the anchors with the slots on the seat. Push until it locks into place (refer to diagram showing bumper bar attachment). NOTE: The bumper bar must be securely attached before using this product.
2. To detach the bumper bar, press the release button on the bottom of the bar and pull the bar out of the anchor. Swing the bar upwards to access the seat (refer to diagram showing bumper bar detachment).

Attaching the Seat

• ONLY approved Snap Tech™ products can be used on the frame.
• Attach the seat by lining up the seat anchors on the side of the seat with the anchors on the stroller frame and pushing them together until they lock securely (refer to diagram showing seat attachment). The seat can face in either direction, frontward or backward.
• To remove the seat or infant car seat, push both release buttons on each side of the seat anchors and lift the seat upwards. DO NOT remove with child in the seat.

Adjusting the Seat

• The seats can be adjusted into upright and reclined positions. Pull the recline button on the rear of the seat and rotate the seat into the desired position (refer to diagram showing seat adjustment).

Removable Canopy

• To attach the removable canopy: Align the posts on the canopy clips with the holes on the toddler seat tubes. Attach the canopy to the seat frame using the hook and loop fasteners (refer to diagram showing canopy attachment).
• Push or pull on the front edge of the canopy while holding the rear of the canopy in place to open and close it (refer to diagram showing canopy operation).

Operation

Brakes

⚠️ WARNING: Always set brakes when the stroller is not being pushed so that it will not roll away. NEVER leave the stroller unattended on a hill or incline, as it may slide down.

1. To engage brakes, apply downward pressure to the brake levers located on the rear axle. You may need to roll the stroller back and forth to fully engage the brake (refer to diagram showing brake engagement). NOTE: Check that the stroller will not move once the brakes are properly applied.
2. To release the brakes, gently lift up on the brake levers.

Securing the Child

⚠️ WARNING: Avoid serious injury from falling or sliding out. Always use the safety harness.

STRANGULATION HAZARD: A child can strangle in loose straps. Never leave a child in the seat when straps are loose or undone.

1. The shoulder straps of the 5-point harness have 3 attachment positions. Select the position that places the shoulder strap level with, or below, the top of the child's shoulders (refer to diagram showing harness positions).
2. To adjust harness height, unhook the shoulder strap from the crotch buckle. Feed the shoulder strap through the harness spread slots (located on the rear of the seat underneath the fabric). Feed the shoulder strap through the appropriate slot and reattach it to the crotch buckle.
3. Carefully place the child in the stroller seat and bring the safety harness around the child's waist and over the child's shoulders. Place the crotch strap between the child's legs. Insert the male end of each shoulder/waist belt into the buckle on the crotch strap. Tighten the harness so it is snug around the child's waist and over the child's shoulders (refer to diagram showing harness adjustment).

Releasing the Child

1. To release the child, push the button on the center clasp, and the two harness buckles will pop free (refer to diagram showing harness release).

Sit N' Stand® Features

⚠️ WARNING: The rear platform and jump seat are designed to accommodate a child who is at least 2 1/2 years old, has good balance and coordination, and is not over 40 inches (101 cm) tall.

• Attaching the Joy Ride Platform: Pull the locks back on the platform and attach it to the rear tube of the frame (refer to diagram showing platform attachment). When the platform is not in use, remove it or rotate it upwards and secure it to the basket with the snap. NOTE: Make sure the platform locks onto the frame before use.
• Jump Seat: Always use the 3-point harness while in the seated position facing the stroller handle. Put the seat belt around the child's waist and buckle it to the crotch strap (refer to diagram showing jump seat harness). Adjust the seat belt to be snug around the child's waist.
• Standing: Your child can stand on the riding platform facing forwards or backwards. NOTE: Use caution while standing on the platform. Make sure your child is always holding onto the frame while riding.

Folding the Stroller

⚠️ WARNING: Care must be taken when folding and unfolding the stroller to prevent finger entrapment.

CAUTION: Do not allow children near the stroller while folding.

1. Pull the stroller backwards several inches to adjust the front wheels to the front.
2. Fold the stroller by pulling both release triggers and push the handle down. Make sure the front wheels lie flat, then secure the stroller in the folded position by locking the fold latch, located on the right side of the stroller, over the tab (refer to diagram showing folding mechanism).

Unfolding the Stroller

CAUTION: Do not allow children near the stroller while unfolding.

1. Unlock the release lever (refer to diagram showing release lever) and unfold the stroller frame by pulling upward on the stroller handle until the frame locks into place (refer to diagram showing unfolding mechanism).

Infant Car Seat Attachment

⚠️ WARNING: Avoid serious injury from falling or sliding out. Always use the safety harness of the infant car seat.

• ONLY approved Snap Tech™ products can be used on the frame.
• Attach the car seat by lining up the seat anchors on the side of the car seat with the anchors on the stroller frame and pushing them together until they lock securely (refer to diagram showing car seat attachment).
• To remove the seat or infant car seat, push both release buttons on each side of the seat anchors and lift the seat upwards (refer to diagram showing car seat removal). DO NOT remove the seat with a child in it.

Maintenance

Seat Pad

• To clean the seat pad, use only mild household soap or detergent and warm water on a sponge or clean cloth.

Other Checks

• Regularly check your stroller for loose screws, worn parts, torn material, or stitching. Replace or repair parts as needed.